Merge branch 'for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

Pull libata changes from Tejun Heo:
 "Mostly driver-specific changes.  Nothing too noteworthy.

  This pull request contains three merges from for-3.19-fixes.  The
  first two are to pull ahci_xgene and sata_dwc_460ex fix commits which
  are depended upon by later changes.  The last one is to pull in a fix
  patch which missed the v3.19-rc window"

* 'for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (24 commits)
  ahci_xgene: Fix the dma state machine lockup for the ATA_CMD_SMART PIO mode command.
  ata: libahci: Use of_platform_device_create only if supported
  sata_mv: Delete unnecessary checks before the function call "phy_power_off"
  ata: Delete unnecessary checks before the function call "pci_dev_put"
  ata: pata_platform: fix owner module reference mismatch for scsi host
  ata: ahci_platform: fix owner module reference mismatch for scsi host
  pata_pdc2027x: Use 64-bit timekeeping
  ata: libahci: Fix devres cleanup on failure
  ata: libahci: Allow using multiple regulators
  Documentation: bindings: Add the regulator property to the sub-nodes AHCI bindings
  ata: libahci: Clean-up the ahci_platform_en/disable_phys functions
  sata_rcar: extend PM methods
  sata_dwc_460ex: disable compilation on ARM and ARM64
  ata: libata-core: Remove unused function
  sata_dwc_460ex: convert to devm_kzalloc in ->probe()
  sata_dwc_460ex: remove extra message
  sata_dwc_460ex: use np local variable in ->probe()
  sata_dwc_460ex: fix most of the sparse warnings
  sata_dwc_460ex: enable COMPILE_TEST for the driver
  sata_dwc_460ex: remove redundant dev_set_drvdata
  ...

Documentation/devicetree/bindings/ata/ahci-platform.txt

@@ -37,9 +37,10 @@ Required properties when using sub-nodes:
 
 
 Sub-nodes required properties:
-- reg               : the port number
-- phys              : reference to the SATA PHY node
-
+- reg		    : the port number
+And at least one of the following properties:
+- phys		    : reference to the SATA PHY node
+- target-supply    : regulator for SATA target power
 
 Examples:
         sata@ffe08000 {
@@ -68,10 +69,12 @@ With sub-nodes:
 		sata0: sata-port@0 {
 			reg = <0>;
 			phys = <&sata_phy 0>;
+			target-supply = <&reg_sata0>;
 		};
 
 		sata1: sata-port@1 {
 			reg = <1>;
 			phys = <&sata_phy 1>;
+			target-supply = <&reg_sata1>;;
 		};
 	};

drivers/ata/Kconfig

@@ -269,7 +269,7 @@ config ATA_PIIX
 
 config SATA_DWC
 	tristate "DesignWare Cores SATA support"
-	depends on 460EX
+	depends on 460EX || (COMPILE_TEST && !(ARM || ARM64))
 	help
 	  This option enables support for the on-chip SATA controller of the
 	  AppliedMicro processor 460EX.

drivers/ata/ahci.h

@@ -333,7 +333,7 @@ struct ahci_host_priv {
 	u32			em_msg_type;	/* EM message type */
 	bool			got_runtime_pm; /* Did we do pm_runtime_get? */
 	struct clk		*clks[AHCI_MAX_CLKS]; /* Optional */
-	struct regulator	*target_pwr;	/* Optional */
+	struct regulator	**target_pwrs;	/* Optional */
 	/*
 	 * If platform uses PHYs. There is a 1:1 relation between the port number and
 	 * the PHY position in this array.
@@ -354,6 +354,10 @@ extern int ahci_ignore_sss;
 extern struct device_attribute *ahci_shost_attrs[];
 extern struct device_attribute *ahci_sdev_attrs[];
 
+/*
+ * This must be instantiated by the edge drivers.  Read the comments
+ * for ATA_BASE_SHT
+ */
 #define AHCI_SHT(drv_name)						\
 	ATA_NCQ_SHT(drv_name),						\
 	.can_queue		= AHCI_MAX_CMDS - 1,			\

drivers/ata/ahci_da850.c

@@ -16,6 +16,8 @@
 #include <linux/ahci_platform.h>
 #include "ahci.h"
 
+#define DRV_NAME "ahci_da850"
+
 /* SATA PHY Control Register offset from AHCI base */
 #define SATA_P0PHYCR_REG	0x178
 
@@ -59,6 +61,10 @@ static const struct ata_port_info ahci_da850_port_info = {
 	.port_ops	= &ahci_platform_ops,
 };
 
+static struct scsi_host_template ahci_platform_sht = {
+	AHCI_SHT(DRV_NAME),
+};
+
 static int ahci_da850_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -85,7 +91,8 @@ static int ahci_da850_probe(struct platform_device *pdev)
 
 	da850_sata_init(dev, pwrdn_reg, hpriv->mmio);
 
-	rc = ahci_platform_init_host(pdev, hpriv, &ahci_da850_port_info);
+	rc = ahci_platform_init_host(pdev, hpriv, &ahci_da850_port_info,
+				     &ahci_platform_sht);
 	if (rc)
 		goto disable_resources;
 
@@ -102,7 +109,7 @@ static struct platform_driver ahci_da850_driver = {
 	.probe = ahci_da850_probe,
 	.remove = ata_platform_remove_one,
 	.driver = {
-		.name = "ahci_da850",
+		.name = DRV_NAME,
 		.pm = &ahci_da850_pm_ops,
 	},
 };

drivers/ata/ahci_imx.c

@@ -28,6 +28,8 @@
 #include <linux/libata.h>
 #include "ahci.h"
 
+#define DRV_NAME "ahci-imx"
+
 enum {
 	/* Timer 1-ms Register */
 	IMX_TIMER1MS				= 0x00e0,
@@ -221,11 +223,9 @@ static int imx_sata_enable(struct ahci_host_priv *hpriv)
 	if (imxpriv->no_device)
 		return 0;
 
-	if (hpriv->target_pwr) {
-		ret = regulator_enable(hpriv->target_pwr);
-		if (ret)
-			return ret;
-	}
+	ret = ahci_platform_enable_regulators(hpriv);
+	if (ret)
+		return ret;
 
 	ret = clk_prepare_enable(imxpriv->sata_ref_clk);
 	if (ret < 0)
@@ -270,8 +270,7 @@ static int imx_sata_enable(struct ahci_host_priv *hpriv)
 disable_clk:
 	clk_disable_unprepare(imxpriv->sata_ref_clk);
 disable_regulator:
-	if (hpriv->target_pwr)
-		regulator_disable(hpriv->target_pwr);
+	ahci_platform_disable_regulators(hpriv);
 
 	return ret;
 }
@@ -291,8 +290,7 @@ static void imx_sata_disable(struct ahci_host_priv *hpriv)
 
 	clk_disable_unprepare(imxpriv->sata_ref_clk);
 
-	if (hpriv->target_pwr)
-		regulator_disable(hpriv->target_pwr);
+	ahci_platform_disable_regulators(hpriv);
 }
 
 static void ahci_imx_error_handler(struct ata_port *ap)
@@ -524,6 +522,10 @@ static u32 imx_ahci_parse_props(struct device *dev,
 	return reg_value;
 }
 
+static struct scsi_host_template ahci_platform_sht = {
+	AHCI_SHT(DRV_NAME),
+};
+
 static int imx_ahci_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -620,7 +622,8 @@ static int imx_ahci_probe(struct platform_device *pdev)
 	reg_val = clk_get_rate(imxpriv->ahb_clk) / 1000;
 	writel(reg_val, hpriv->mmio + IMX_TIMER1MS);
 
-	ret = ahci_platform_init_host(pdev, hpriv, &ahci_imx_port_info);
+	ret = ahci_platform_init_host(pdev, hpriv, &ahci_imx_port_info,
+				      &ahci_platform_sht);
 	if (ret)
 		goto disable_sata;
 
@@ -678,7 +681,7 @@ static struct platform_driver imx_ahci_driver = {
 	.probe = imx_ahci_probe,
 	.remove = ata_platform_remove_one,
 	.driver = {
-		.name = "ahci-imx",
+		.name = DRV_NAME,
 		.of_match_table = imx_ahci_of_match,
 		.pm = &ahci_imx_pm_ops,
 	},

drivers/ata/ahci_mvebu.c

@@ -19,6 +19,8 @@
 #include <linux/platform_device.h>
 #include "ahci.h"
 
+#define DRV_NAME "ahci-mvebu"
+
 #define AHCI_VENDOR_SPECIFIC_0_ADDR  0xa0
 #define AHCI_VENDOR_SPECIFIC_0_DATA  0xa4
 
@@ -67,6 +69,10 @@ static const struct ata_port_info ahci_mvebu_port_info = {
 	.port_ops  = &ahci_platform_ops,
 };
 
+static struct scsi_host_template ahci_platform_sht = {
+	AHCI_SHT(DRV_NAME),
+};
+
 static int ahci_mvebu_probe(struct platform_device *pdev)
 {
 	struct ahci_host_priv *hpriv;
@@ -88,7 +94,8 @@ static int ahci_mvebu_probe(struct platform_device *pdev)
 	ahci_mvebu_mbus_config(hpriv, dram);
 	ahci_mvebu_regret_option(hpriv);
 
-	rc = ahci_platform_init_host(pdev, hpriv, &ahci_mvebu_port_info);
+	rc = ahci_platform_init_host(pdev, hpriv, &ahci_mvebu_port_info,
+				     &ahci_platform_sht);
 	if (rc)
 		goto disable_resources;
 
@@ -114,7 +121,7 @@ static struct platform_driver ahci_mvebu_driver = {
 	.probe = ahci_mvebu_probe,
 	.remove = ata_platform_remove_one,
 	.driver = {
-		.name = "ahci-mvebu",
+		.name = DRV_NAME,
 		.of_match_table = ahci_mvebu_of_match,
 	},
 };

drivers/ata/ahci_platform.c

@@ -22,6 +22,8 @@
 #include <linux/ahci_platform.h>
 #include "ahci.h"
 
+#define DRV_NAME "ahci"
+
 static const struct ata_port_info ahci_port_info = {
 	.flags		= AHCI_FLAG_COMMON,
 	.pio_mask	= ATA_PIO4,
@@ -29,6 +31,10 @@ static const struct ata_port_info ahci_port_info = {
 	.port_ops	= &ahci_platform_ops,
 };
 
+static struct scsi_host_template ahci_platform_sht = {
+	AHCI_SHT(DRV_NAME),
+};
+
 static int ahci_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -46,7 +52,8 @@ static int ahci_probe(struct platform_device *pdev)
 	if (of_device_is_compatible(dev->of_node, "hisilicon,hisi-ahci"))
 		hpriv->flags |= AHCI_HFLAG_NO_FBS | AHCI_HFLAG_NO_NCQ;
 
-	rc = ahci_platform_init_host(pdev, hpriv, &ahci_port_info);
+	rc = ahci_platform_init_host(pdev, hpriv, &ahci_port_info,
+				     &ahci_platform_sht);
 	if (rc)
 		goto disable_resources;
 
@@ -75,7 +82,7 @@ static struct platform_driver ahci_driver = {
 	.probe = ahci_probe,
 	.remove = ata_platform_remove_one,
 	.driver = {
-		.name = "ahci",
+		.name = DRV_NAME,
 		.of_match_table = ahci_of_match,
 		.pm = &ahci_pm_ops,
 	},

drivers/ata/ahci_st.c

@@ -23,6 +23,8 @@
 
 #include "ahci.h"
 
+#define DRV_NAME  "st_ahci"
+
 #define ST_AHCI_OOBR			0xbc
 #define ST_AHCI_OOBR_WE			BIT(31)
 #define ST_AHCI_OOBR_CWMIN_SHIFT	24
@@ -140,6 +142,10 @@ static const struct ata_port_info st_ahci_port_info = {
 	.port_ops       = &st_ahci_port_ops,
 };
 
+static struct scsi_host_template ahci_platform_sht = {
+	AHCI_SHT(DRV_NAME),
+};
+
 static int st_ahci_probe(struct platform_device *pdev)
 {
 	struct st_ahci_drv_data *drv_data;
@@ -166,7 +172,8 @@ static int st_ahci_probe(struct platform_device *pdev)
 	if (err)
 		return err;
 
-	err = ahci_platform_init_host(pdev, hpriv, &st_ahci_port_info);
+	err = ahci_platform_init_host(pdev, hpriv, &st_ahci_port_info,
+				      &ahci_platform_sht);
 	if (err) {
 		ahci_platform_disable_resources(hpriv);
 		return err;
@@ -229,7 +236,7 @@ MODULE_DEVICE_TABLE(of, st_ahci_match);
 
 static struct platform_driver st_ahci_driver = {
 	.driver = {
-		.name = "st_ahci",
+		.name = DRV_NAME,
 		.pm = &st_ahci_pm_ops,
 		.of_match_table = of_match_ptr(st_ahci_match),
 	},

drivers/ata/ahci_sunxi.c

@@ -27,6 +27,8 @@
 #include <linux/regulator/consumer.h>
 #include "ahci.h"
 
+#define DRV_NAME "ahci-sunxi"
+
 /* Insmod parameters */
 static bool enable_pmp;
 module_param(enable_pmp, bool, 0);
@@ -169,6 +171,10 @@ static const struct ata_port_info ahci_sunxi_port_info = {
 	.port_ops	= &ahci_platform_ops,
 };
 
+static struct scsi_host_template ahci_platform_sht = {
+	AHCI_SHT(DRV_NAME),
+};
+
 static int ahci_sunxi_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -200,7 +206,8 @@ static int ahci_sunxi_probe(struct platform_device *pdev)
 	if (!enable_pmp)
 		hpriv->flags |= AHCI_HFLAG_NO_PMP;
 
-	rc = ahci_platform_init_host(pdev, hpriv, &ahci_sunxi_port_info);
+	rc = ahci_platform_init_host(pdev, hpriv, &ahci_sunxi_port_info,
+				     &ahci_platform_sht);
 	if (rc)
 		goto disable_resources;
 
@@ -251,7 +258,7 @@ static struct platform_driver ahci_sunxi_driver = {
 	.probe = ahci_sunxi_probe,
 	.remove = ata_platform_remove_one,
 	.driver = {
-		.name = "ahci-sunxi",
+		.name = DRV_NAME,
 		.of_match_table = ahci_sunxi_of_match,
 		.pm = &ahci_sunxi_pm_ops,
 	},

drivers/ata/ahci_tegra.c

@@ -31,6 +31,8 @@
 
 #include "ahci.h"
 
+#define DRV_NAME "tegra-ahci"
+
 #define SATA_CONFIGURATION_0				0x180
 #define SATA_CONFIGURATION_EN_FPCI			BIT(0)
 
@@ -289,6 +291,10 @@ static const struct of_device_id tegra_ahci_of_match[] = {
 };
 MODULE_DEVICE_TABLE(of, tegra_ahci_of_match);
 
+static struct scsi_host_template ahci_platform_sht = {
+	AHCI_SHT(DRV_NAME),
+};
+
 static int tegra_ahci_probe(struct platform_device *pdev)
 {
 	struct ahci_host_priv *hpriv;
@@ -354,7 +360,8 @@ static int tegra_ahci_probe(struct platform_device *pdev)
 	if (ret)
 		return ret;
 
-	ret = ahci_platform_init_host(pdev, hpriv, &ahci_tegra_port_info);
+	ret = ahci_platform_init_host(pdev, hpriv, &ahci_tegra_port_info,
+				      &ahci_platform_sht);
 	if (ret)
 		goto deinit_controller;
 
@@ -370,7 +377,7 @@ static struct platform_driver tegra_ahci_driver = {
 	.probe = tegra_ahci_probe,
 	.remove = ata_platform_remove_one,
 	.driver = {
-		.name = "tegra-ahci",
+		.name = DRV_NAME,
 		.of_match_table = tegra_ahci_of_match,
 	},
 	/* LP0 suspend support not implemented */

drivers/ata/ahci_xgene.c

@@ -30,6 +30,8 @@
 #include <linux/phy/phy.h>
 #include "ahci.h"
 
+#define DRV_NAME "xgene-ahci"
+
 /* Max # of disk per a controller */
 #define MAX_AHCI_CHN_PERCTR		2
 
@@ -85,6 +87,7 @@ struct xgene_ahci_context {
 	struct ahci_host_priv *hpriv;
 	struct device *dev;
 	u8 last_cmd[MAX_AHCI_CHN_PERCTR]; /* tracking the last command issued*/
+	u32 class[MAX_AHCI_CHN_PERCTR]; /* tracking the class of device */
 	void __iomem *csr_core;		/* Core CSR address of IP */
 	void __iomem *csr_diag;		/* Diag CSR address of IP */
 	void __iomem *csr_axi;		/* AXI CSR address of IP */
@@ -104,18 +107,70 @@ static int xgene_ahci_init_memram(struct xgene_ahci_context *ctx)
 	return 0;
 }
 
+/**
+ * xgene_ahci_poll_reg_val- Poll a register on a specific value.
+ * @ap : ATA port of interest.
+ * @reg : Register of interest.
+ * @val : Value to be attained.
+ * @interval : waiting interval for polling.
+ * @timeout : timeout for achieving the value.
+ */
+static int xgene_ahci_poll_reg_val(struct ata_port *ap,
+				   void __iomem *reg, unsigned
+				   int val, unsigned long interval,
+				   unsigned long timeout)
+{
+	unsigned long deadline;
+	unsigned int tmp;
+
+	tmp = ioread32(reg);
+	deadline = ata_deadline(jiffies, timeout);
+
+	while (tmp != val && time_before(jiffies, deadline)) {
+		ata_msleep(ap, interval);
+		tmp = ioread32(reg);
+	}
+
+	return tmp;
+}
+
 /**
  * xgene_ahci_restart_engine - Restart the dma engine.
  * @ap : ATA port of interest
  *
- * Restarts the dma engine inside the controller.
+ * Waits for completion of multiple commands and restarts
+ * the DMA engine inside the controller.
  */
 static int xgene_ahci_restart_engine(struct ata_port *ap)
 {
 	struct ahci_host_priv *hpriv = ap->host->private_data;
+	struct ahci_port_priv *pp = ap->private_data;
+	void __iomem *port_mmio = ahci_port_base(ap);
+	u32 fbs;
+
+	/*
+	 * In case of PMP multiple IDENTIFY DEVICE commands can be
+	 * issued inside PxCI. So need to poll PxCI for the
+	 * completion of outstanding IDENTIFY DEVICE commands before
+	 * we restart the DMA engine.
+	 */
+	if (xgene_ahci_poll_reg_val(ap, port_mmio +
+				    PORT_CMD_ISSUE, 0x0, 1, 100))
+		  return -EBUSY;
 
 	ahci_stop_engine(ap);
 	ahci_start_fis_rx(ap);
+
+	/*
+	 * Enable the PxFBS.FBS_EN bit as it
+	 * gets cleared due to stopping the engine.
+	 */
+	if (pp->fbs_supported) {
+		fbs = readl(port_mmio + PORT_FBS);
+		writel(fbs | PORT_FBS_EN, port_mmio + PORT_FBS);
+		fbs = readl(port_mmio + PORT_FBS);
+	}
+
 	hpriv->start_engine(ap);
 
 	return 0;
@@ -125,11 +180,17 @@ static int xgene_ahci_restart_engine(struct ata_port *ap)
  * xgene_ahci_qc_issue - Issue commands to the device
  * @qc: Command to issue
  *
- * Due to Hardware errata for IDENTIFY DEVICE command and PACKET
- * command of ATAPI protocol set, the controller cannot clear the BSY bit
- * after receiving the PIO setup FIS. This results in the DMA state machine
- * going into the CMFatalErrorUpdate state and locks up. By restarting the
- * DMA engine, it removes the controller out of lock up state.
+ * Due to Hardware errata for IDENTIFY DEVICE command, the controller cannot
+ * clear the BSY bit after receiving the PIO setup FIS. This results in the dma
+ * state machine goes into the CMFatalErrorUpdate state and locks up. By
+ * restarting the dma engine, it removes the controller out of lock up state.
+ *
+ * Due to H/W errata, the controller is unable to save the PMP
+ * field fetched from command header before sending the H2D FIS.
+ * When the device returns the PMP port field in the D2H FIS, there is
+ * a mismatch and results in command completion failure. The
+ * workaround is to write the pmp value to PxFBS.DEV field before issuing
+ * any command to PMP.
  */
 static unsigned int xgene_ahci_qc_issue(struct ata_queued_cmd *qc)
 {
@@ -137,9 +198,23 @@ static unsigned int xgene_ahci_qc_issue(struct ata_queued_cmd *qc)
 	struct ahci_host_priv *hpriv = ap->host->private_data;
 	struct xgene_ahci_context *ctx = hpriv->plat_data;
 	int rc = 0;
+	u32 port_fbs;
+	void *port_mmio = ahci_port_base(ap);
+
+	/*
+	 * Write the pmp value to PxFBS.DEV
+	 * for case of Port Mulitplier.
+	 */
+	if (ctx->class[ap->port_no] == ATA_DEV_PMP) {
+		port_fbs = readl(port_mmio + PORT_FBS);
+		port_fbs &= ~PORT_FBS_DEV_MASK;
+		port_fbs |= qc->dev->link->pmp << PORT_FBS_DEV_OFFSET;
+		writel(port_fbs, port_mmio + PORT_FBS);
+	}
 
 	if (unlikely((ctx->last_cmd[ap->port_no] == ATA_CMD_ID_ATA) ||
-	    (ctx->last_cmd[ap->port_no] == ATA_CMD_PACKET)))
+	    (ctx->last_cmd[ap->port_no] == ATA_CMD_PACKET) ||
+	    (ctx->last_cmd[ap->port_no] == ATA_CMD_SMART)))
 		xgene_ahci_restart_engine(ap);
 
 	rc = ahci_qc_issue(qc);
@@ -365,16 +440,119 @@ static void xgene_ahci_host_stop(struct ata_host *host)
 	ahci_platform_disable_resources(hpriv);
 }
 
+/**
+ * xgene_ahci_pmp_softreset - Issue the softreset to the drives connected
+ *                            to Port Multiplier.
+ * @link: link to reset
+ * @class: Return value to indicate class of device
+ * @deadline: deadline jiffies for the operation
+ *
+ * Due to H/W errata, the controller is unable to save the PMP
+ * field fetched from command header before sending the H2D FIS.
+ * When the device returns the PMP port field in the D2H FIS, there is
+ * a mismatch and results in command completion failure. The workaround
+ * is to write the pmp value to PxFBS.DEV field before issuing any command
+ * to PMP.
+ */
+static int xgene_ahci_pmp_softreset(struct ata_link *link, unsigned int *class,
+			  unsigned long deadline)
+{
+	int pmp = sata_srst_pmp(link);
+	struct ata_port *ap = link->ap;
+	u32 rc;
+	void *port_mmio = ahci_port_base(ap);
+	u32 port_fbs;
+
+	/*
+	 * Set PxFBS.DEV field with pmp
+	 * value.
+	 */
+	port_fbs = readl(port_mmio + PORT_FBS);
+	port_fbs &= ~PORT_FBS_DEV_MASK;
+	port_fbs |= pmp << PORT_FBS_DEV_OFFSET;
+	writel(port_fbs, port_mmio + PORT_FBS);
+
+	rc = ahci_do_softreset(link, class, pmp, deadline, ahci_check_ready);
+
+	return rc;
+}
+
+/**
+ * xgene_ahci_softreset - Issue the softreset to the drive.
+ * @link: link to reset
+ * @class: Return value to indicate class of device
+ * @deadline: deadline jiffies for the operation
+ *
+ * Due to H/W errata, the controller is unable to save the PMP
+ * field fetched from command header before sending the H2D FIS.
+ * When the device returns the PMP port field in the D2H FIS, there is
+ * a mismatch and results in command completion failure. The workaround
+ * is to write the pmp value to PxFBS.DEV field before issuing any command
+ * to PMP. Here is the algorithm to detect PMP :
+ *
+ * 1. Save the PxFBS value
+ * 2. Program PxFBS.DEV with pmp value send by framework. Framework sends
+ *    0xF for both PMP/NON-PMP initially
+ * 3. Issue softreset
+ * 4. If signature class is PMP goto 6
+ * 5. restore the original PxFBS and goto 3
+ * 6. return
+ */
+static int xgene_ahci_softreset(struct ata_link *link, unsigned int *class,
+			  unsigned long deadline)
+{
+	int pmp = sata_srst_pmp(link);
+	struct ata_port *ap = link->ap;
+	struct ahci_host_priv *hpriv = ap->host->private_data;
+	struct xgene_ahci_context *ctx = hpriv->plat_data;
+	void *port_mmio = ahci_port_base(ap);
+	u32 port_fbs;
+	u32 port_fbs_save;
+	u32 retry = 1;
+	u32 rc;
+
+	port_fbs_save = readl(port_mmio + PORT_FBS);
+
+	/*
+	 * Set PxFBS.DEV field with pmp
+	 * value.
+	 */
+	port_fbs = readl(port_mmio + PORT_FBS);
+	port_fbs &= ~PORT_FBS_DEV_MASK;
+	port_fbs |= pmp << PORT_FBS_DEV_OFFSET;
+	writel(port_fbs, port_mmio + PORT_FBS);
+
+softreset_retry:
+	rc = ahci_do_softreset(link, class, pmp,
+			       deadline, ahci_check_ready);
+
+	ctx->class[ap->port_no] = *class;
+	if (*class != ATA_DEV_PMP) {
+		/*
+		 * Retry for normal drives without
+		 * setting PxFBS.DEV field with pmp value.
+		 */
+		if (retry--) {
+			writel(port_fbs_save, port_mmio + PORT_FBS);
+			goto softreset_retry;
+		}
+	}
+
+	return rc;
+}
+
 static struct ata_port_operations xgene_ahci_ops = {
 	.inherits = &ahci_ops,
 	.host_stop = xgene_ahci_host_stop,
 	.hardreset = xgene_ahci_hardreset,
 	.read_id = xgene_ahci_read_id,
 	.qc_issue = xgene_ahci_qc_issue,
+	.softreset = xgene_ahci_softreset,
+	.pmp_softreset = xgene_ahci_pmp_softreset
 };
 
 static const struct ata_port_info xgene_ahci_port_info = {
-	.flags = AHCI_FLAG_COMMON,
+	.flags = AHCI_FLAG_COMMON | ATA_FLAG_PMP,
 	.pio_mask = ATA_PIO4,
 	.udma_mask = ATA_UDMA6,
 	.port_ops = &xgene_ahci_ops,
@@ -446,6 +624,10 @@ static int xgene_ahci_mux_select(struct xgene_ahci_context *ctx)
 	return val & CFG_SATA_ENET_SELECT_MASK ? -1 : 0;
 }
 
+static struct scsi_host_template ahci_platform_sht = {
+	AHCI_SHT(DRV_NAME),
+};
+
 static int xgene_ahci_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -523,7 +705,8 @@ static int xgene_ahci_probe(struct platform_device *pdev)
 skip_clk_phy:
 	hpriv->flags = AHCI_HFLAG_NO_PMP | AHCI_HFLAG_NO_NCQ;
 
-	rc = ahci_platform_init_host(pdev, hpriv, &xgene_ahci_port_info);
+	rc = ahci_platform_init_host(pdev, hpriv, &xgene_ahci_port_info,
+				     &ahci_platform_sht);
 	if (rc)
 		goto disable_resources;
 
@@ -545,7 +728,7 @@ static struct platform_driver xgene_ahci_driver = {
 	.probe = xgene_ahci_probe,
 	.remove = ata_platform_remove_one,
 	.driver = {
-		.name = "xgene-ahci",
+		.name = DRV_NAME,
 		.of_match_table = xgene_ahci_of_match,
 	},
 };

drivers/ata/libata-core.c

@@ -1751,33 +1751,6 @@ unsigned ata_exec_internal(struct ata_device *dev,
 				    timeout);
 }
 
-/**
- *	ata_do_simple_cmd - execute simple internal command
- *	@dev: Device to which the command is sent
- *	@cmd: Opcode to execute
- *
- *	Execute a 'simple' command, that only consists of the opcode
- *	'cmd' itself, without filling any other registers
- *
- *	LOCKING:
- *	Kernel thread context (may sleep).
- *
- *	RETURNS:
- *	Zero on success, AC_ERR_* mask on failure
- */
-unsigned int ata_do_simple_cmd(struct ata_device *dev, u8 cmd)
-{
-	struct ata_taskfile tf;
-
-	ata_tf_init(dev, &tf);
-
-	tf.command = cmd;
-	tf.flags |= ATA_TFLAG_DEVICE;
-	tf.protocol = ATA_PROT_NODATA;
-
-	return ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
-}
-
 /**
  *	ata_pio_need_iordy	-	check if iordy needed
  *	@adev: ATA device

drivers/ata/libata-eh.c

@@ -1635,7 +1635,6 @@ unsigned int atapi_eh_request_sense(struct ata_device *dev,
 
 	DPRINTK("ATAPI request sense\n");
 
-	/* FIXME: is this needed? */
 	memset(sense_buf, 0, SCSI_SENSE_BUFFERSIZE);
 
 	/* initialize sense_buf with the error register,

drivers/ata/libata-scsi.c

@@ -1995,8 +1995,8 @@ static unsigned int ata_scsiop_inq_std(struct ata_scsi_args *args, u8 *rbuf)
 
 	VPRINTK("ENTER\n");
 
-	/* set scsi removeable (RMB) bit per ata bit */
-	if (ata_id_removeable(args->id))
+	/* set scsi removable (RMB) bit per ata bit */
+	if (ata_id_removable(args->id))
 		hdr[1] |= (1 << 7);
 
 	if (args->dev->class == ATA_DEV_ZAC) {

drivers/ata/libata.h

@@ -76,7 +76,6 @@ extern unsigned ata_exec_internal_sg(struct ata_device *dev,
 				     struct ata_taskfile *tf, const u8 *cdb,
 				     int dma_dir, struct scatterlist *sg,
 				     unsigned int n_elem, unsigned long timeout);
-extern unsigned int ata_do_simple_cmd(struct ata_device *dev, u8 cmd);
 extern int ata_wait_ready(struct ata_link *link, unsigned long deadline,
 			  int (*check_ready)(struct ata_link *link));
 extern int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class,

drivers/ata/pata_cs5530.c

@@ -276,10 +276,8 @@ static int cs5530_init_chip(void)
 	pci_dev_put(cs5530_0);
 	return 0;
 fail_put:
-	if (master_0)
-		pci_dev_put(master_0);
-	if (cs5530_0)
-		pci_dev_put(cs5530_0);
+	pci_dev_put(master_0);
+	pci_dev_put(cs5530_0);
 	return -ENODEV;
 }
 

drivers/ata/pata_of_platform.c

@@ -16,6 +16,12 @@
 #include <linux/ata_platform.h>
 #include <linux/libata.h>
 
+#define DRV_NAME "pata_of_platform"
+
+static struct scsi_host_template pata_platform_sht = {
+	ATA_PIO_SHT(DRV_NAME),
+};
+
 static int pata_of_platform_probe(struct platform_device *ofdev)
 {
 	int ret;
@@ -63,7 +69,7 @@ static int pata_of_platform_probe(struct platform_device *ofdev)
 	pio_mask |= (1 << pio_mode) - 1;
 
 	return __pata_platform_probe(&ofdev->dev, &io_res, &ctl_res, irq_res,
-				     reg_shift, pio_mask);
+				     reg_shift, pio_mask, &pata_platform_sht);
 }
 
 static struct of_device_id pata_of_platform_match[] = {
@@ -74,7 +80,7 @@ MODULE_DEVICE_TABLE(of, pata_of_platform_match);
 
 static struct platform_driver pata_of_platform_driver = {
 	.driver = {
-		.name = "pata_of_platform",
+		.name = DRV_NAME,
 		.of_match_table = pata_of_platform_match,
 	},
 	.probe		= pata_of_platform_probe,

drivers/ata/pata_pdc2027x.c

@@ -28,6 +28,7 @@
 #include <linux/blkdev.h>
 #include <linux/delay.h>
 #include <linux/device.h>
+#include <linux/ktime.h>
 #include <scsi/scsi.h>
 #include <scsi/scsi_host.h>
 #include <scsi/scsi_cmnd.h>
@@ -605,7 +606,7 @@ static long pdc_detect_pll_input_clock(struct ata_host *host)
 	void __iomem *mmio_base = host->iomap[PDC_MMIO_BAR];
 	u32 scr;
 	long start_count, end_count;
-	struct timeval start_time, end_time;
+	ktime_t start_time, end_time;
 	long pll_clock, usec_elapsed;
 
 	/* Start the test mode */
@@ -616,14 +617,14 @@ static long pdc_detect_pll_input_clock(struct ata_host *host)
 
 	/* Read current counter value */
 	start_count = pdc_read_counter(host);
-	do_gettimeofday(&start_time);
+	start_time = ktime_get();
 
 	/* Let the counter run for 100 ms. */
 	mdelay(100);
 
 	/* Read the counter values again */
 	end_count = pdc_read_counter(host);
-	do_gettimeofday(&end_time);
+	end_time = ktime_get();
 
 	/* Stop the test mode */
 	scr = ioread32(mmio_base + PDC_SYS_CTL);
@@ -632,8 +633,7 @@ static long pdc_detect_pll_input_clock(struct ata_host *host)
 	ioread32(mmio_base + PDC_SYS_CTL); /* flush */
 
 	/* calculate the input clock in Hz */
-	usec_elapsed = (end_time.tv_sec - start_time.tv_sec) * 1000000 +
-		(end_time.tv_usec - start_time.tv_usec);
+	usec_elapsed = (long) ktime_us_delta(end_time, start_time);
 
 	pll_clock = ((start_count - end_count) & 0x3fffffff) / 100 *
 		(100000000 / usec_elapsed);

drivers/ata/pata_platform.c

@@ -78,6 +78,7 @@ static void pata_platform_setup_port(struct ata_ioports *ioaddr,
  *	@irq_res: Resource representing IRQ and its flags
  *	@ioport_shift: I/O port shift
  *	@__pio_mask: PIO mask
+ *	@sht: scsi_host_template to use when registering
  *
  *	Register a platform bus IDE interface. Such interfaces are PIO and we
  *	assume do not support IRQ sharing.
@@ -99,7 +100,8 @@ static void pata_platform_setup_port(struct ata_ioports *ioaddr,
  */
 int __pata_platform_probe(struct device *dev, struct resource *io_res,
 			  struct resource *ctl_res, struct resource *irq_res,
-			  unsigned int ioport_shift, int __pio_mask)
+			  unsigned int ioport_shift, int __pio_mask,
+			  struct scsi_host_template *sht)
 {
 	struct ata_host *host;
 	struct ata_port *ap;
@@ -170,7 +172,7 @@ int __pata_platform_probe(struct device *dev, struct resource *io_res,
 
 	/* activate */
 	return ata_host_activate(host, irq, irq ? ata_sff_interrupt : NULL,
-				 irq_flags, &pata_platform_sht);
+				 irq_flags, sht);
 }
 EXPORT_SYMBOL_GPL(__pata_platform_probe);
 
@@ -216,7 +218,7 @@ static int pata_platform_probe(struct platform_device *pdev)
 
 	return __pata_platform_probe(&pdev->dev, io_res, ctl_res, irq_res,
 				     pp_info ? pp_info->ioport_shift : 0,
-				     pio_mask);
+				     pio_mask, &pata_platform_sht);
 }
 
 static struct platform_driver pata_platform_driver = {

drivers/ata/sata_dwc_460ex.c

@@ -48,6 +48,18 @@
 #define DRV_NAME        "sata-dwc"
 #define DRV_VERSION     "1.3"
 
+#ifndef out_le32
+#define out_le32(a, v)	__raw_writel(__cpu_to_le32(v), (void __iomem *)(a))
+#endif
+
+#ifndef in_le32
+#define in_le32(a)	__le32_to_cpu(__raw_readl((void __iomem *)(a)))
+#endif
+
+#ifndef NO_IRQ
+#define NO_IRQ		0
+#endif
+
 /* SATA DMA driver Globals */
 #define DMA_NUM_CHANS		1
 #define DMA_NUM_CHAN_REGS	8
@@ -273,7 +285,7 @@ struct sata_dwc_device {
 	struct device		*dev;		/* generic device struct */
 	struct ata_probe_ent	*pe;		/* ptr to probe-ent */
 	struct ata_host		*host;
-	u8			*reg_base;
+	u8 __iomem		*reg_base;
 	struct sata_dwc_regs	*sata_dwc_regs;	/* DW Synopsys SATA specific */
 	int			irq_dma;
 };
@@ -323,7 +335,9 @@ struct sata_dwc_host_priv {
 	struct	device	*dwc_dev;
 	int	dma_channel;
 };
-struct sata_dwc_host_priv host_pvt;
+
+static struct sata_dwc_host_priv host_pvt;
+
 /*
  * Prototypes
  */
@@ -580,9 +594,9 @@ static int map_sg_to_lli(struct scatterlist *sg, int num_elems,
 
 	sms_val = 0;
 	dms_val = 1 + host_pvt.dma_channel;
-	dev_dbg(host_pvt.dwc_dev, "%s: sg=%p nelem=%d lli=%p dma_lli=0x%08x"
-		" dmadr=0x%08x\n", __func__, sg, num_elems, lli, (u32)dma_lli,
-		(u32)dmadr_addr);
+	dev_dbg(host_pvt.dwc_dev,
+		"%s: sg=%p nelem=%d lli=%p dma_lli=0x%pad dmadr=0x%p\n",
+		__func__, sg, num_elems, lli, &dma_lli, dmadr_addr);
 
 	bl = get_burst_length_encode(AHB_DMA_BRST_DFLT);
 
@@ -773,7 +787,7 @@ static void dma_dwc_exit(struct sata_dwc_device *hsdev)
 {
 	dev_dbg(host_pvt.dwc_dev, "%s:\n", __func__);
 	if (host_pvt.sata_dma_regs) {
-		iounmap(host_pvt.sata_dma_regs);
+		iounmap((void __iomem *)host_pvt.sata_dma_regs);
 		host_pvt.sata_dma_regs = NULL;
 	}
 
@@ -818,7 +832,7 @@ static int sata_dwc_scr_read(struct ata_link *link, unsigned int scr, u32 *val)
 		return -EINVAL;
 	}
 
-	*val = in_le32((void *)link->ap->ioaddr.scr_addr + (scr * 4));
+	*val = in_le32(link->ap->ioaddr.scr_addr + (scr * 4));
 	dev_dbg(link->ap->dev, "%s: id=%d reg=%d val=val=0x%08x\n",
 		__func__, link->ap->print_id, scr, *val);
 
@@ -834,21 +848,19 @@ static int sata_dwc_scr_write(struct ata_link *link, unsigned int scr, u32 val)
 			 __func__, scr);
 		return -EINVAL;
 	}
-	out_le32((void *)link->ap->ioaddr.scr_addr + (scr * 4), val);
+	out_le32(link->ap->ioaddr.scr_addr + (scr * 4), val);
 
 	return 0;
 }
 
 static u32 core_scr_read(unsigned int scr)
 {
-	return in_le32((void __iomem *)(host_pvt.scr_addr_sstatus) +\
-			(scr * 4));
+	return in_le32(host_pvt.scr_addr_sstatus + (scr * 4));
 }
 
 static void core_scr_write(unsigned int scr, u32 val)
 {
-	out_le32((void __iomem *)(host_pvt.scr_addr_sstatus) + (scr * 4),
-		val);
+	out_le32(host_pvt.scr_addr_sstatus + (scr * 4), val);
 }
 
 static void clear_serror(void)
@@ -856,7 +868,6 @@ static void clear_serror(void)
 	u32 val;
 	val = core_scr_read(SCR_ERROR);
 	core_scr_write(SCR_ERROR, val);
-
 }
 
 static void clear_interrupt_bit(struct sata_dwc_device *hsdev, u32 bit)
@@ -1256,24 +1267,24 @@ static void sata_dwc_enable_interrupts(struct sata_dwc_device *hsdev)
 
 static void sata_dwc_setup_port(struct ata_ioports *port, unsigned long base)
 {
-	port->cmd_addr = (void *)base + 0x00;
-	port->data_addr = (void *)base + 0x00;
+	port->cmd_addr = (void __iomem *)base + 0x00;
+	port->data_addr = (void __iomem *)base + 0x00;
 
-	port->error_addr = (void *)base + 0x04;
-	port->feature_addr = (void *)base + 0x04;
+	port->error_addr = (void __iomem *)base + 0x04;
+	port->feature_addr = (void __iomem *)base + 0x04;
 
-	port->nsect_addr = (void *)base + 0x08;
+	port->nsect_addr = (void __iomem *)base + 0x08;
 
-	port->lbal_addr = (void *)base + 0x0c;
-	port->lbam_addr = (void *)base + 0x10;
-	port->lbah_addr = (void *)base + 0x14;
+	port->lbal_addr = (void __iomem *)base + 0x0c;
+	port->lbam_addr = (void __iomem *)base + 0x10;
+	port->lbah_addr = (void __iomem *)base + 0x14;
 
-	port->device_addr = (void *)base + 0x18;
-	port->command_addr = (void *)base + 0x1c;
-	port->status_addr = (void *)base + 0x1c;
+	port->device_addr = (void __iomem *)base + 0x18;
+	port->command_addr = (void __iomem *)base + 0x1c;
+	port->status_addr = (void __iomem *)base + 0x1c;
 
-	port->altstatus_addr = (void *)base + 0x20;
-	port->ctl_addr = (void *)base + 0x20;
+	port->altstatus_addr = (void __iomem *)base + 0x20;
+	port->ctl_addr = (void __iomem *)base + 0x20;
 }
 
 /*
@@ -1314,7 +1325,7 @@ static int sata_dwc_port_start(struct ata_port *ap)
 	for (i = 0; i < SATA_DWC_QCMD_MAX; i++)
 		hsdevp->cmd_issued[i] = SATA_DWC_CMD_ISSUED_NOT;
 
-	ap->bmdma_prd = 0;	/* set these so libata doesn't use them */
+	ap->bmdma_prd = NULL;	/* set these so libata doesn't use them */
 	ap->bmdma_prd_dma = 0;
 
 	/*
@@ -1511,8 +1522,8 @@ static void sata_dwc_qc_prep_by_tag(struct ata_queued_cmd *qc, u8 tag)
 
 	dma_chan = dma_dwc_xfer_setup(sg, qc->n_elem, hsdevp->llit[tag],
 				      hsdevp->llit_dma[tag],
-				      (void *__iomem)(&hsdev->sata_dwc_regs->\
-				      dmadr), qc->dma_dir);
+				      (void __iomem *)&hsdev->sata_dwc_regs->dmadr,
+				      qc->dma_dir);
 	if (dma_chan < 0) {
 		dev_err(ap->dev, "%s: dma_dwc_xfer_setup returns err %d\n",
 			__func__, dma_chan);
@@ -1585,8 +1596,8 @@ static void sata_dwc_error_handler(struct ata_port *ap)
 	ata_sff_error_handler(ap);
 }
 
-int sata_dwc_hardreset(struct ata_link *link, unsigned int *class,
-			unsigned long deadline)
+static int sata_dwc_hardreset(struct ata_link *link, unsigned int *class,
+			      unsigned long deadline)
 {
 	struct sata_dwc_device *hsdev = HSDEV_FROM_AP(link->ap);
 	int ret;
@@ -1618,7 +1629,7 @@ static struct scsi_host_template sata_dwc_sht = {
 	 * max of 1. This will get fixed in in a future release.
 	 */
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.can_queue		= ATA_DEF_QUEUE,	/* ATA_MAX_QUEUE */
+	/* .can_queue		= ATA_MAX_QUEUE, */
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 };
 
@@ -1655,7 +1666,7 @@ static int sata_dwc_probe(struct platform_device *ofdev)
 	struct sata_dwc_device *hsdev;
 	u32 idr, versionr;
 	char *ver = (char *)&versionr;
-	u8 *base = NULL;
+	u8 __iomem *base;
 	int err = 0;
 	int irq;
 	struct ata_host *host;
@@ -1665,12 +1676,12 @@ static int sata_dwc_probe(struct platform_device *ofdev)
 	u32 dma_chan;
 
 	/* Allocate DWC SATA device */
-	hsdev = kzalloc(sizeof(*hsdev), GFP_KERNEL);
-	if (hsdev == NULL) {
-		dev_err(&ofdev->dev, "kmalloc failed for hsdev\n");
-		err = -ENOMEM;
-		goto error;
-	}
+	host = ata_host_alloc_pinfo(&ofdev->dev, ppi, SATA_DWC_MAX_PORTS);
+	hsdev = devm_kzalloc(&ofdev->dev, sizeof(*hsdev), GFP_KERNEL);
+	if (!host || !hsdev)
+		return -ENOMEM;
+
+	host->private_data = hsdev;
 
 	if (of_property_read_u32(np, "dma-channel", &dma_chan)) {
 		dev_warn(&ofdev->dev, "no dma-channel property set."
@@ -1680,12 +1691,11 @@ static int sata_dwc_probe(struct platform_device *ofdev)
 	host_pvt.dma_channel = dma_chan;
 
 	/* Ioremap SATA registers */
-	base = of_iomap(ofdev->dev.of_node, 0);
+	base = of_iomap(np, 0);
 	if (!base) {
 		dev_err(&ofdev->dev, "ioremap failed for SATA register"
 			" address\n");
-		err = -ENODEV;
-		goto error_kmalloc;
+		return -ENODEV;
 	}
 	hsdev->reg_base = base;
 	dev_dbg(&ofdev->dev, "ioremap done for SATA register address\n");
@@ -1693,16 +1703,6 @@ static int sata_dwc_probe(struct platform_device *ofdev)
 	/* Synopsys DWC SATA specific Registers */
 	hsdev->sata_dwc_regs = (void *__iomem)(base + SATA_DWC_REG_OFFSET);
 
-	/* Allocate and fill host */
-	host = ata_host_alloc_pinfo(&ofdev->dev, ppi, SATA_DWC_MAX_PORTS);
-	if (!host) {
-		dev_err(&ofdev->dev, "ata_host_alloc_pinfo failed\n");
-		err = -ENOMEM;
-		goto error_iomap;
-	}
-
-	host->private_data = hsdev;
-
 	/* Setup port */
 	host->ports[0]->ioaddr.cmd_addr = base;
 	host->ports[0]->ioaddr.scr_addr = base + SATA_DWC_SCR_OFFSET;
@@ -1716,7 +1716,7 @@ static int sata_dwc_probe(struct platform_device *ofdev)
 		   idr, ver[0], ver[1], ver[2]);
 
 	/* Get SATA DMA interrupt number */
-	irq = irq_of_parse_and_map(ofdev->dev.of_node, 1);
+	irq = irq_of_parse_and_map(np, 1);
 	if (irq == NO_IRQ) {
 		dev_err(&ofdev->dev, "no SATA DMA irq\n");
 		err = -ENODEV;
@@ -1724,7 +1724,7 @@ static int sata_dwc_probe(struct platform_device *ofdev)
 	}
 
 	/* Get physical SATA DMA register base address */
-	host_pvt.sata_dma_regs = of_iomap(ofdev->dev.of_node, 1);
+	host_pvt.sata_dma_regs = (void *)of_iomap(np, 1);
 	if (!(host_pvt.sata_dma_regs)) {
 		dev_err(&ofdev->dev, "ioremap failed for AHBDMA register"
 			" address\n");
@@ -1744,7 +1744,7 @@ static int sata_dwc_probe(struct platform_device *ofdev)
 	sata_dwc_enable_interrupts(hsdev);
 
 	/* Get SATA interrupt number */
-	irq = irq_of_parse_and_map(ofdev->dev.of_node, 0);
+	irq = irq_of_parse_and_map(np, 0);
 	if (irq == NO_IRQ) {
 		dev_err(&ofdev->dev, "no SATA DMA irq\n");
 		err = -ENODEV;
@@ -1770,9 +1770,6 @@ static int sata_dwc_probe(struct platform_device *ofdev)
 	iounmap((void __iomem *)host_pvt.sata_dma_regs);
 error_iomap:
 	iounmap(base);
-error_kmalloc:
-	kfree(hsdev);
-error:
 	return err;
 }
 
@@ -1783,15 +1780,12 @@ static int sata_dwc_remove(struct platform_device *ofdev)
 	struct sata_dwc_device *hsdev = host->private_data;
 
 	ata_host_detach(host);
-	dev_set_drvdata(dev, NULL);
 
 	/* Free SATA DMA resources */
 	dma_dwc_exit(hsdev);
 
 	iounmap((void __iomem *)host_pvt.sata_dma_regs);
 	iounmap(hsdev->reg_base);
-	kfree(hsdev);
-	kfree(host);
 	dev_dbg(&ofdev->dev, "done\n");
 	return 0;
 }

drivers/ata/sata_mv.c

@@ -4185,8 +4185,7 @@ static int mv_platform_probe(struct platform_device *pdev)
 			clk_disable_unprepare(hpriv->port_clks[port]);
 			clk_put(hpriv->port_clks[port]);
 		}
-		if (hpriv->port_phys[port])
-			phy_power_off(hpriv->port_phys[port]);
+		phy_power_off(hpriv->port_phys[port]);
 	}
 
 	return rc;
@@ -4216,8 +4215,7 @@ static int mv_platform_remove(struct platform_device *pdev)
 			clk_disable_unprepare(hpriv->port_clks[port]);
 			clk_put(hpriv->port_clks[port]);
 		}
-		if (hpriv->port_phys[port])
-			phy_power_off(hpriv->port_phys[port]);
+		phy_power_off(hpriv->port_phys[port]);
 	}
 	return 0;
 }

drivers/ata/sata_rcar.c

@@ -2,8 +2,8 @@
  * Renesas R-Car SATA driver
  *
  * Author: Vladimir Barinov <source@cogentembedded.com>
- * Copyright (C) 2013 Cogent Embedded, Inc.
- * Copyright (C) 2013 Renesas Solutions Corp.
+ * Copyright (C) 2013-2015 Cogent Embedded, Inc.
+ * Copyright (C) 2013-2015 Renesas Solutions Corp.
  *
  * This program is free software; you can redistribute  it and/or modify it
  * under  the terms of  the GNU General  Public License as published by the
@@ -992,9 +992,30 @@ static int sata_rcar_resume(struct device *dev)
 	return 0;
 }
 
+static int sata_rcar_restore(struct device *dev)
+{
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct sata_rcar_priv *priv = host->private_data;
+
+	clk_prepare_enable(priv->clk);
+
+	sata_rcar_setup_port(host);
+
+	/* initialize host controller */
+	sata_rcar_init_controller(host);
+
+	ata_host_resume(host);
+
+	return 0;
+}
+
 static const struct dev_pm_ops sata_rcar_pm_ops = {
 	.suspend	= sata_rcar_suspend,
 	.resume		= sata_rcar_resume,
+	.freeze		= sata_rcar_suspend,
+	.thaw		= sata_rcar_resume,
+	.poweroff	= sata_rcar_suspend,
+	.restore	= sata_rcar_restore,
 };
 #endif
 

include/linux/ahci_platform.h

@@ -21,16 +21,20 @@ struct device;
 struct ata_port_info;
 struct ahci_host_priv;
 struct platform_device;
+struct scsi_host_template;
 
 int ahci_platform_enable_clks(struct ahci_host_priv *hpriv);
 void ahci_platform_disable_clks(struct ahci_host_priv *hpriv);
+int ahci_platform_enable_regulators(struct ahci_host_priv *hpriv);
+void ahci_platform_disable_regulators(struct ahci_host_priv *hpriv);
 int ahci_platform_enable_resources(struct ahci_host_priv *hpriv);
 void ahci_platform_disable_resources(struct ahci_host_priv *hpriv);
 struct ahci_host_priv *ahci_platform_get_resources(
 	struct platform_device *pdev);
 int ahci_platform_init_host(struct platform_device *pdev,
 			    struct ahci_host_priv *hpriv,
-			    const struct ata_port_info *pi_template);
+			    const struct ata_port_info *pi_template,
+			    struct scsi_host_template *sht);
 
 int ahci_platform_suspend_host(struct device *dev);
 int ahci_platform_resume_host(struct device *dev);

include/linux/ata.h

@@ -503,7 +503,7 @@ struct ata_bmdma_prd {
 #define ata_id_has_dma(id)	((id)[ATA_ID_CAPABILITY] & (1 << 8))
 #define ata_id_has_ncq(id)	((id)[ATA_ID_SATA_CAPABILITY] & (1 << 8))
 #define ata_id_queue_depth(id)	(((id)[ATA_ID_QUEUE_DEPTH] & 0x1f) + 1)
-#define ata_id_removeable(id)	((id)[ATA_ID_CONFIG] & (1 << 7))
+#define ata_id_removable(id)	((id)[ATA_ID_CONFIG] & (1 << 7))
 #define ata_id_has_atapi_AN(id)	\
 	((((id)[ATA_ID_SATA_CAPABILITY] != 0x0000) && \
 	  ((id)[ATA_ID_SATA_CAPABILITY] != 0xffff)) && \

include/linux/ata_platform.h

@@ -10,12 +10,15 @@ struct pata_platform_info {
 	unsigned int ioport_shift;
 };
 
+struct scsi_host_template;
+
 extern int __pata_platform_probe(struct device *dev,
 				 struct resource *io_res,
 				 struct resource *ctl_res,
 				 struct resource *irq_res,
 				 unsigned int ioport_shift,
-				 int __pio_mask);
+				 int __pio_mask,
+				 struct scsi_host_template *sht);
 
 /*
  * Marvell SATA private data

include/linux/libata.h

@@ -1340,6 +1340,12 @@ extern const struct ata_port_operations ata_base_port_ops;
 extern const struct ata_port_operations sata_port_ops;
 extern struct device_attribute *ata_common_sdev_attrs[];
 
+/*
+ * All sht initializers (BASE, PIO, BMDMA, NCQ) must be instantiated
+ * by the edge drivers.  Because the 'module' field of sht must be the
+ * edge driver's module reference, otherwise the driver can be unloaded
+ * even if the scsi_device is being accessed.
+ */
 #define ATA_BASE_SHT(drv_name)					\
 	.module			= THIS_MODULE,			\
 	.name			= drv_name,			\