dt-bindings:iio:imu:adi,adis16480: txt to yaml conversion

Alexandru is currently listed as maintainer on basis of last person
to touch the binding.

Whilst the driver only uses one interrupt, the hardware can route events
to one and dataready signal to the other so we should allow for either
1 or 2 interrupts.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201031184854.745828-12-jic23@kernel.org

Documentation/devicetree/bindings/iio/imu/adi,adis16480.txt

-
-Analog Devices ADIS16480 and similar IMUs
-
-Required properties for the ADIS16480:
-
-- compatible: Must be one of
-	* "adi,adis16375"
-	* "adi,adis16480"
-	* "adi,adis16485"
-	* "adi,adis16488"
-	* "adi,adis16490"
-	* "adi,adis16495-1"
-	* "adi,adis16495-2"
-	* "adi,adis16495-3"
-	* "adi,adis16497-1"
-	* "adi,adis16497-2"
-	* "adi,adis16497-3"
-- reg: SPI chip select number for the device
-- spi-max-frequency: Max SPI frequency to use
-	see: Documentation/devicetree/bindings/spi/spi-bus.txt
-- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt
-- spi-cpol: See Documentation/devicetree/bindings/spi/spi-bus.txt
-- interrupts: interrupt mapping for IRQ, accepted values are:
-	* IRQF_TRIGGER_RISING
-	* IRQF_TRIGGER_FALLING
-
-Optional properties:
-
-- interrupt-names: Data ready line selection. Valid values are:
-	* DIO1
-	* DIO2
-	* DIO3
-	* DIO4
-	If this field is left empty, DIO1 is assigned as default data ready
-	signal.
-- reset-gpios: must be the device tree identifier of the RESET pin. As the line
-	is active low, it should be marked GPIO_ACTIVE_LOW.
-- clocks: phandle to the external clock. Should be set according to
-	"clock-names".
-	If this field is left empty together with the "clock-names" field, then
-	the internal clock is used.
-- clock-names: The name of the external clock to be used. Valid values are:
-	* sync: In sync mode, the internal clock is disabled and the frequency
-		of the external clock signal establishes therate of data
-		collection and processing. See Fig 14 and 15 in the datasheet.
-		The clock-frequency must be:
-		* 3000 to 4500 Hz for adis1649x devices.
-		* 700 to 2400 Hz for adis1648x devices.
-	* pps: In Pulse Per Second (PPS) Mode, the rate of data collection and
-	       production is equal to the product of the external clock
-	       frequency and the scale factor in the SYNC_SCALE register, see
-	       Table 154 in the datasheet.
-	       The clock-frequency must be:
-	       * 1 to 128 Hz for adis1649x devices.
-	       * This mode is not supported by adis1648x devices.
-	If this field is left empty together with the "clocks" field, then the
-	internal clock is used.
-- adi,ext-clk-pin: The DIOx line to be used as an external clock input.
-	Valid values are:
-	* DIO1
-	* DIO2
-	* DIO3
-	* DIO4
-	Each DIOx pin supports only one function at a time (data ready line
-	selection or external clock input). When a single pin has two
-	two assignments, the enable bit for the lower priority function
-	automatically resets to zero (disabling the lower priority function).
-	Data ready has highest priority.
-	If this field is left empty, DIO2 is assigned as default external clock
-	input pin.
-
-Example:
-
-	imu@0 {
-		compatible = "adi,adis16495-1";
-		reg = <0>;
-		spi-max-frequency = <3200000>;
-		spi-cpol;
-		spi-cpha;
-		interrupts = <25 IRQF_TRIGGER_FALLING>;
-		interrupt-parent = <&gpio>;
-		interrupt-names = "DIO2";
-		clocks = <&adis16495_sync>;
-		clock-names = "sync";
-		adi,ext-clk-pin = "DIO1";
-	};

Documentation/devicetree/bindings/iio/imu/adi,adis16480.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/imu/adi,adis16480.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADIS16480 and similar IMUs
+
+maintainers:
+  - Alexandru Ardelean <alexandru.ardelean@analog.com>
+
+properties:
+  compatible:
+    enum:
+      - adi,adis16375
+      - adi,adis16480
+      - adi,adis16485
+      - adi,adis16488
+      - adi,adis16490
+      - adi,adis16495-1
+      - adi,adis16495-2
+      - adi,adis16495-3
+      - adi,adis16497-1
+      - adi,adis16497-2
+      - adi,adis16497-3
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    minItems: 1
+    maxItems: 2
+    description: |
+      Accepted interrupt types are:
+      * IRQ_TYPE_EDGE_RISING
+      * IRQ_TYPE_EDGE_FALLING
+
+  interrupt-names:
+    minItems: 1
+    maxItems: 2
+    description:
+      Default if not supplied is DIO1.
+    items:
+      enum:
+        - DIO1
+        - DIO2
+        - DIO3
+        - DIO4
+
+  spi-max-frequency: true
+
+  spi-cpha: true
+  spi-cpol: true
+
+  reset-gpios:
+    maxItems: 1
+    description: Connected to RESET pin which is active low.
+
+  clocks:
+    maxItems: 1
+    description: If not provided, then the internal clock is used.
+
+  clock-names:
+    description: |
+      sync: In sync mode, the internal clock is disabled and the frequency
+            of the external clock signal establishes therate of data
+            collection and processing. See Fig 14 and 15 in the datasheet.
+            The clock-frequency must be:
+            * 3000 to 4500 Hz for adis1649x devices.
+            * 700 to 2400 Hz for adis1648x devices.
+      pps:  In Pulse Per Second (PPS) Mode, the rate of data collection and
+            production is equal to the product of the external clock
+            frequency and the scale factor in the SYNC_SCALE register, see
+            Table 154 in the datasheet.
+            The clock-frequency must be:
+            * 1 to 128 Hz for adis1649x devices.
+            * This mode is not supported by adis1648x devices.
+    enum:
+      - sync
+      - pps
+
+  adi,ext-clk-pin:
+    $ref: /schemas/types.yaml#/definitions/string
+    description: |
+      The DIOx line to be used as an external clock input.
+      Each DIOx pin supports only one function at a time (data ready line
+      selection or external clock input). When a single pin has two
+      two assignments, the enable bit for the lower priority function
+      automatically resets to zero (disabling the lower priority function).
+      Data ready has highest priority.
+      If not provided then DIO2 is assigned as default external clock
+      input pin.
+    enum:
+      - DIO1
+      - DIO2
+      - DIO3
+      - DIO4
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - spi-cpha
+  - spi-cpol
+  - spi-max-frequency
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        imu@0 {
+            compatible = "adi,adis16495-1";
+            reg = <0>;
+            spi-max-frequency = <3200000>;
+            spi-cpol;
+            spi-cpha;
+            interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+            interrupt-parent = <&gpio>;
+            interrupt-names = "DIO2";
+            clocks = <&adis16495_sync>;
+            clock-names = "sync";
+            adi,ext-clk-pin = "DIO1";
+        };
+    };
+...