avr32: data param to at32_add_device_mci() must be non-NULL

at32_add_device_mci() will refuse to add the mci device if the data
parameter is NULL. Fix up the favr-32 and hammerhead boards so that this
doesn't happen.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Alex Raimondi <mailinglist@miromico.ch>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>

arch/avr32/boards/favr-32/setup.c

@@ -17,6 +17,7 @@
 #include <linux/linkage.h>
 #include <linux/gpio.h>
 #include <linux/leds.h>
+#include <linux/atmel-mci.h>
 #include <linux/atmel-pwm-bl.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
@@ -79,6 +80,14 @@ static struct spi_board_info __initdata spi1_board_info[] = {
 	},
 };
 
+static struct mci_platform_data __initdata mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= -ENODEV,
+		.wp_pin		= -ENODEV,
+	},
+};
+
 static struct fb_videomode __initdata lb104v03_modes[] = {
 	{
 		.name		= "640x480 @ 50",
@@ -321,7 +330,7 @@ static int __init favr32_init(void)
 
 	at32_add_device_pwm(1 << atmel_pwm_bl_pdata.pwm_channel);
 	at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info));
-	at32_add_device_mci(0, NULL);
+	at32_add_device_mci(0, &mci0_data);
 	at32_add_device_usba(0, NULL);
 	at32_add_device_lcdc(0, &favr32_lcdc_data, fbmem_start, fbmem_size, 0);
 

arch/avr32/boards/hammerhead/setup.c

@@ -7,6 +7,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
+#include <linux/atmel-mci.h>
 #include <linux/clk.h>
 #include <linux/fb.h>
 #include <linux/etherdevice.h>
@@ -86,6 +87,14 @@ struct atmel_lcdfb_info __initdata hammerhead_lcdc_data = {
 };
 #endif
 
+static struct mci_platform_data __initdata mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= -ENODEV,
+		.wp_pin		= -ENODEV,
+	},
+};
+
 struct eth_addr {
 	u8 addr[6];
 };
@@ -204,7 +213,7 @@ static int __init hammerhead_init(void)
 #ifdef CONFIG_BOARD_HAMMERHEAD_FPGA
 	at32_add_device_hh_fpga();
 #endif
-	at32_add_device_mci(0, NULL);
+	at32_add_device_mci(0, &mci0_data);
 
 #ifdef CONFIG_BOARD_HAMMERHEAD_USB
 	at32_add_device_usba(0, NULL);