Commit 4b09a6fa authored by Stefan Mavrodiev's avatar Stefan Mavrodiev Committed by Maxime Ripard

ARM: dts: sun8i: Add dts file for Olimex A33-OLinuXino

A33-OLinuXino is A33 development board designed by Olimex LTD.

It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.

It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.
Signed-off-by: default avatarStefan Mavrodiev <stefan.mavrodiev@gmail.com>
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@free-electrons.com>
parent 3d3f05e6
...@@ -783,6 +783,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ ...@@ -783,6 +783,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a33-et-q8-v1.6.dtb \ sun8i-a33-et-q8-v1.6.dtb \
sun8i-a33-ga10h-v1.1.dtb \ sun8i-a33-ga10h-v1.1.dtb \
sun8i-a33-ippo-q8h-v1.2.dtb \ sun8i-a33-ippo-q8h-v1.2.dtb \
sun8i-a33-olinuxino.dtb \
sun8i-a33-q8-tablet.dtb \ sun8i-a33-q8-tablet.dtb \
sun8i-a33-sinlinx-sina33.dtb \ sun8i-a33-sinlinx-sina33.dtb \
sun8i-a83t-allwinner-h8homlet-v2.dtb \ sun8i-a83t-allwinner-h8homlet-v2.dtb \
......
/*
* Copyright 2016 - Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
* Olimex LTD. <support@olimex.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun8i-a33.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
model = "Olimex A33-OLinuXino";
compatible = "olimex,a33-olinuxino","allwinner,sun8i-a33";
aliases {
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pin_olinuxino>;
green {
label = "a33-olinuxino:green:usr";
gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>;
};
};
};
&ehci0 {
status = "okay";
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino>;
vmmc-supply = <&reg_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
cd-inverted;
status = "okay";
};
&ohci0 {
status = "okay";
};
&pio {
led_pin_olinuxino: led_pins@0 {
allwinner,pins = "PB7";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
mmc0_cd_pin_olinuxino: mmc0_cd_pin@0 {
allwinner,pins = "PB4";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
usb0_id_detect_pin: usb0_id_detect_pin@0 {
allwinner,pins = "PB3";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
&r_rsb {
status = "okay";
axp22x: pmic@3a3 {
compatible = "x-powers,axp223";
reg = <0x3a3>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
eldoin-supply = <&reg_dcdc1>;
x-powers,drive-vbus-en;
};
};
#include "axp22x.dtsi"
&reg_aldo1 {
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-io";
};
&reg_aldo2 {
regulator-always-on;
regulator-min-microvolt = <2350000>;
regulator-max-microvolt = <2650000>;
regulator-name = "vdd-dll";
};
&reg_aldo3 {
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-avcc";
};
&reg_dc1sw {
regulator-name = "vcc-lcd";
};
&reg_dc5ldo {
regulator-always-on;
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1400000>;
regulator-name = "vdd-cpus";
};
&reg_dcdc1 {
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-3v3";
};
&reg_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1400000>;
regulator-name = "vdd-sys";
};
&reg_dcdc3 {
regulator-always-on;
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1400000>;
regulator-name = "vdd-cpu";
};
&reg_dcdc5 {
regulator-always-on;
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-name = "vcc-dram";
};
&reg_drivevbus {
regulator-name = "usb0-vbus";
status = "okay";
};
&reg_rtc_ldo {
regulator-name = "vcc-rtc";
};
&simplefb_lcd {
vcc-lcd-supply = <&reg_dc1sw>;
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_b>;
status = "okay";
};
&usb_otg {
dr_mode = "otg";
status = "okay";
};
&usb_power_supply {
status = "okay";
};
&usbphy {
pinctrl-names = "default";
pinctrl-0 = <&usb0_id_detect_pin>;
usb0_id_det-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <&reg_drivevbus>;
status = "okay";
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment