Commit 4d79e042 authored by Chunfeng Yun's avatar Chunfeng Yun Committed by Felipe Balbi

usb: mtu3: add support for usb3.1 IP

Support SuperSpeedPlus for usb3.1 device IP
Signed-off-by: default avatarChunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: default avatarFelipe Balbi <felipe.balbi@linux.intel.com>
parent c776f2c3
......@@ -94,6 +94,7 @@ enum mtu3_speed {
MTU3_SPEED_FULL = 1,
MTU3_SPEED_HIGH = 3,
MTU3_SPEED_SUPER = 4,
MTU3_SPEED_SUPER_PLUS = 5,
};
/**
......
......@@ -237,7 +237,7 @@ void mtu3_ep_stall_set(struct mtu3_ep *mep, bool set)
void mtu3_dev_on_off(struct mtu3 *mtu, int is_on)
{
if (mtu->is_u3_ip && (mtu->max_speed == USB_SPEED_SUPER))
if (mtu->is_u3_ip && mtu->max_speed >= USB_SPEED_SUPER)
mtu3_ss_func_set(mtu, is_on);
else
mtu3_hs_softconn_set(mtu, is_on);
......@@ -547,6 +547,9 @@ static void mtu3_set_speed(struct mtu3 *mtu)
mtu3_clrbits(mbase, U3D_USB3_CONFIG, USB3_EN);
/* HS/FS detected by HW */
mtu3_setbits(mbase, U3D_POWER_MANAGEMENT, HS_ENABLE);
} else if (mtu->max_speed == USB_SPEED_SUPER) {
mtu3_clrbits(mtu->ippc_base, SSUSB_U3_CTRL(0),
SSUSB_U3_PORT_SSP_SPEED);
}
dev_info(mtu->dev, "max_speed: %s\n",
......@@ -624,6 +627,10 @@ static irqreturn_t mtu3_link_isr(struct mtu3 *mtu)
udev_speed = USB_SPEED_SUPER;
maxpkt = 512;
break;
case MTU3_SPEED_SUPER_PLUS:
udev_speed = USB_SPEED_SUPER_PLUS;
maxpkt = 512;
break;
default:
udev_speed = USB_SPEED_UNKNOWN;
break;
......@@ -825,14 +832,15 @@ int ssusb_gadget_init(struct ssusb_mtk *ssusb)
case USB_SPEED_FULL:
case USB_SPEED_HIGH:
case USB_SPEED_SUPER:
case USB_SPEED_SUPER_PLUS:
break;
default:
dev_err(dev, "invalid max_speed: %s\n",
usb_speed_string(mtu->max_speed));
/* fall through */
case USB_SPEED_UNKNOWN:
/* default as SS */
mtu->max_speed = USB_SPEED_SUPER;
/* default as SSP */
mtu->max_speed = USB_SPEED_SUPER_PLUS;
break;
}
......
......@@ -89,6 +89,7 @@ static int mtu3_ep_enable(struct mtu3_ep *mep)
switch (mtu->g.speed) {
case USB_SPEED_SUPER:
case USB_SPEED_SUPER_PLUS:
if (usb_endpoint_xfer_int(desc) ||
usb_endpoint_xfer_isoc(desc)) {
interval = desc->bInterval;
......@@ -456,7 +457,7 @@ static int mtu3_gadget_wakeup(struct usb_gadget *gadget)
return -EOPNOTSUPP;
spin_lock_irqsave(&mtu->lock, flags);
if (mtu->g.speed == USB_SPEED_SUPER) {
if (mtu->g.speed >= USB_SPEED_SUPER) {
mtu3_setbits(mtu->mac_base, U3D_LINK_POWER_CONTROL, UX_EXIT);
} else {
mtu3_setbits(mtu->mac_base, U3D_POWER_MANAGEMENT, RESUME);
......
......@@ -212,8 +212,8 @@ ep0_get_status(struct mtu3 *mtu, const struct usb_ctrlrequest *setup)
case USB_RECIP_DEVICE:
result[0] = mtu->is_self_powered << USB_DEVICE_SELF_POWERED;
result[0] |= mtu->may_wakeup << USB_DEVICE_REMOTE_WAKEUP;
/* superspeed only */
if (mtu->g.speed == USB_SPEED_SUPER) {
if (mtu->g.speed >= USB_SPEED_SUPER) {
result[0] |= mtu->u1_enable << USB_DEV_STAT_U1_ENABLED;
result[0] |= mtu->u2_enable << USB_DEV_STAT_U2_ENABLED;
}
......@@ -329,8 +329,8 @@ static int ep0_handle_feature_dev(struct mtu3 *mtu,
handled = handle_test_mode(mtu, setup);
break;
case USB_DEVICE_U1_ENABLE:
if (mtu->g.speed != USB_SPEED_SUPER ||
mtu->g.state != USB_STATE_CONFIGURED)
if (mtu->g.speed < USB_SPEED_SUPER ||
mtu->g.state != USB_STATE_CONFIGURED)
break;
lpc = mtu3_readl(mbase, U3D_LINK_POWER_CONTROL);
......@@ -344,8 +344,8 @@ static int ep0_handle_feature_dev(struct mtu3 *mtu,
handled = 1;
break;
case USB_DEVICE_U2_ENABLE:
if (mtu->g.speed != USB_SPEED_SUPER ||
mtu->g.state != USB_STATE_CONFIGURED)
if (mtu->g.speed < USB_SPEED_SUPER ||
mtu->g.state != USB_STATE_CONFIGURED)
break;
lpc = mtu3_readl(mbase, U3D_LINK_POWER_CONTROL);
......@@ -384,8 +384,8 @@ static int ep0_handle_feature(struct mtu3 *mtu,
break;
case USB_RECIP_INTERFACE:
/* superspeed only */
if ((value == USB_INTRF_FUNC_SUSPEND)
&& (mtu->g.speed == USB_SPEED_SUPER)) {
if (value == USB_INTRF_FUNC_SUSPEND &&
mtu->g.speed >= USB_SPEED_SUPER) {
/*
* forward the request because function drivers
* should handle it
......
......@@ -467,6 +467,7 @@
#define SSUSB_VBUS_CHG_INT_B_EN BIT(6)
/* U3D_SSUSB_U3_CTRL_0P */
#define SSUSB_U3_PORT_SSP_SPEED BIT(9)
#define SSUSB_U3_PORT_HOST_SEL BIT(2)
#define SSUSB_U3_PORT_PDN BIT(1)
#define SSUSB_U3_PORT_DIS BIT(0)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment