e1000: Add support for the CE4100 reference platform

This patch adds support for the gigabit phys present on the CE4100 reference
platforms.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/e1000/e1000_hw.h

@@ -52,6 +52,7 @@ typedef enum {
 	e1000_82545,
 	e1000_82545_rev_3,
 	e1000_82546,
+	e1000_ce4100,
 	e1000_82546_rev_3,
 	e1000_82541,
 	e1000_82541_rev_2,
@@ -209,9 +210,11 @@ typedef enum {
 } e1000_1000t_rx_status;
 
 typedef enum {
-    e1000_phy_m88 = 0,
-    e1000_phy_igp,
-    e1000_phy_undefined = 0xFF
+	e1000_phy_m88 = 0,
+	e1000_phy_igp,
+	e1000_phy_8211,
+	e1000_phy_8201,
+	e1000_phy_undefined = 0xFF
 } e1000_phy_type;
 
 typedef enum {
@@ -442,6 +445,7 @@ void e1000_io_write(struct e1000_hw *hw, unsigned long port, u32 value);
 #define E1000_DEV_ID_82547EI             0x1019
 #define E1000_DEV_ID_82547EI_MOBILE      0x101A
 #define E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 0x10B5
+#define E1000_DEV_ID_INTEL_CE4100_GBE    0x2E6E
 
 #define NODE_ADDRESS_SIZE 6
 #define ETH_LENGTH_OF_ADDRESS 6
@@ -808,6 +812,16 @@ struct e1000_ffvt_entry {
 #define E1000_CTRL_EXT 0x00018	/* Extended Device Control - RW */
 #define E1000_FLA      0x0001C	/* Flash Access - RW */
 #define E1000_MDIC     0x00020	/* MDI Control - RW */
+
+extern void __iomem *ce4100_gbe_mdio_base_virt;
+#define INTEL_CE_GBE_MDIO_RCOMP_BASE    (ce4100_gbe_mdio_base_virt)
+#define E1000_MDIO_STS  (INTEL_CE_GBE_MDIO_RCOMP_BASE + 0)
+#define E1000_MDIO_CMD  (INTEL_CE_GBE_MDIO_RCOMP_BASE + 4)
+#define E1000_MDIO_DRV  (INTEL_CE_GBE_MDIO_RCOMP_BASE + 8)
+#define E1000_MDC_CMD   (INTEL_CE_GBE_MDIO_RCOMP_BASE + 0xC)
+#define E1000_RCOMP_CTL (INTEL_CE_GBE_MDIO_RCOMP_BASE + 0x20)
+#define E1000_RCOMP_STS (INTEL_CE_GBE_MDIO_RCOMP_BASE + 0x24)
+
 #define E1000_SCTL     0x00024	/* SerDes Control - RW */
 #define E1000_FEXTNVM  0x00028	/* Future Extended NVM register */
 #define E1000_FCAL     0x00028	/* Flow Control Address Low - RW */
@@ -820,6 +834,34 @@ struct e1000_ffvt_entry {
 #define E1000_IMS      0x000D0	/* Interrupt Mask Set - RW */
 #define E1000_IMC      0x000D8	/* Interrupt Mask Clear - WO */
 #define E1000_IAM      0x000E0	/* Interrupt Acknowledge Auto Mask */
+
+/* Auxiliary Control Register. This register is CE4100 specific,
+ * RMII/RGMII function is switched by this register - RW
+ * Following are bits definitions of the Auxiliary Control Register
+ */
+#define E1000_CTL_AUX  0x000E0
+#define E1000_CTL_AUX_END_SEL_SHIFT     10
+#define E1000_CTL_AUX_ENDIANESS_SHIFT   8
+#define E1000_CTL_AUX_RGMII_RMII_SHIFT  0
+
+/* descriptor and packet transfer use CTL_AUX.ENDIANESS */
+#define E1000_CTL_AUX_DES_PKT   (0x0 << E1000_CTL_AUX_END_SEL_SHIFT)
+/* descriptor use CTL_AUX.ENDIANESS, packet use default */
+#define E1000_CTL_AUX_DES       (0x1 << E1000_CTL_AUX_END_SEL_SHIFT)
+/* descriptor use default, packet use CTL_AUX.ENDIANESS */
+#define E1000_CTL_AUX_PKT       (0x2 << E1000_CTL_AUX_END_SEL_SHIFT)
+/* all use CTL_AUX.ENDIANESS */
+#define E1000_CTL_AUX_ALL       (0x3 << E1000_CTL_AUX_END_SEL_SHIFT)
+
+#define E1000_CTL_AUX_RGMII     (0x0 << E1000_CTL_AUX_RGMII_RMII_SHIFT)
+#define E1000_CTL_AUX_RMII      (0x1 << E1000_CTL_AUX_RGMII_RMII_SHIFT)
+
+/* LW little endian, Byte big endian */
+#define E1000_CTL_AUX_LWLE_BBE  (0x0 << E1000_CTL_AUX_ENDIANESS_SHIFT)
+#define E1000_CTL_AUX_LWLE_BLE  (0x1 << E1000_CTL_AUX_ENDIANESS_SHIFT)
+#define E1000_CTL_AUX_LWBE_BBE  (0x2 << E1000_CTL_AUX_ENDIANESS_SHIFT)
+#define E1000_CTL_AUX_LWBE_BLE  (0x3 << E1000_CTL_AUX_ENDIANESS_SHIFT)
+
 #define E1000_RCTL     0x00100	/* RX Control - RW */
 #define E1000_RDTR1    0x02820	/* RX Delay Timer (1) - RW */
 #define E1000_RDBAL1   0x02900	/* RX Descriptor Base Address Low (1) - RW */
@@ -1011,6 +1053,7 @@ struct e1000_ffvt_entry {
  * in more current versions of the 8254x. Despite the difference in location,
  * the registers function in the same manner.
  */
+#define E1000_82542_CTL_AUX  E1000_CTL_AUX
 #define E1000_82542_CTRL     E1000_CTRL
 #define E1000_82542_CTRL_DUP E1000_CTRL_DUP
 #define E1000_82542_STATUS   E1000_STATUS
@@ -1571,6 +1614,11 @@ struct e1000_hw {
 #define E1000_MDIC_INT_EN    0x20000000
 #define E1000_MDIC_ERROR     0x40000000
 
+#define INTEL_CE_GBE_MDIC_OP_WRITE      0x04000000
+#define INTEL_CE_GBE_MDIC_OP_READ       0x00000000
+#define INTEL_CE_GBE_MDIC_GO            0x80000000
+#define INTEL_CE_GBE_MDIC_READ_ERROR    0x80000000
+
 #define E1000_KUMCTRLSTA_MASK           0x0000FFFF
 #define E1000_KUMCTRLSTA_OFFSET         0x001F0000
 #define E1000_KUMCTRLSTA_OFFSET_SHIFT   16
@@ -2871,6 +2919,11 @@ struct e1000_host_command_info {
 #define M88E1111_I_PHY_ID  0x01410CC0
 #define L1LXT971A_PHY_ID   0x001378E0
 
+#define RTL8211B_PHY_ID    0x001CC910
+#define RTL8201N_PHY_ID    0x8200
+#define RTL_PHY_CTRL_FD    0x0100 /* Full duplex.0=half; 1=full */
+#define RTL_PHY_CTRL_SPD_100    0x200000 /* Force 100Mb */
+
 /* Bits...
  * 15-5: page
  * 4-0: register offset

drivers/net/e1000/e1000_main.c

@@ -28,6 +28,12 @@
 
 #include "e1000.h"
 #include <net/ip6_checksum.h>
+#include <linux/io.h>
+
+/* Intel Media SOC GbE MDIO physical base address */
+static unsigned long ce4100_gbe_mdio_base_phy;
+/* Intel Media SOC GbE MDIO virtual base address */
+void __iomem *ce4100_gbe_mdio_base_virt;
 
 char e1000_driver_name[] = "e1000";
 static char e1000_driver_string[] = "Intel(R) PRO/1000 Network Driver";
@@ -79,6 +85,7 @@ static DEFINE_PCI_DEVICE_TABLE(e1000_pci_tbl) = {
 	INTEL_E1000_ETHERNET_DEVICE(0x108A),
 	INTEL_E1000_ETHERNET_DEVICE(0x1099),
 	INTEL_E1000_ETHERNET_DEVICE(0x10B5),
+	INTEL_E1000_ETHERNET_DEVICE(0x2E6E),
 	/* required last entry */
 	{0,}
 };
@@ -459,6 +466,7 @@ static void e1000_power_down_phy(struct e1000_adapter *adapter)
 		case e1000_82545:
 		case e1000_82545_rev_3:
 		case e1000_82546:
+		case e1000_ce4100:
 		case e1000_82546_rev_3:
 		case e1000_82541:
 		case e1000_82541_rev_2:
@@ -573,6 +581,7 @@ void e1000_reset(struct e1000_adapter *adapter)
 	case e1000_82545:
 	case e1000_82545_rev_3:
 	case e1000_82546:
+	case e1000_ce4100:
 	case e1000_82546_rev_3:
 		pba = E1000_PBA_48K;
 		break;
@@ -894,6 +903,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 	static int global_quad_port_a = 0; /* global ksp3 port a indication */
 	int i, err, pci_using_dac;
 	u16 eeprom_data = 0;
+	u16 tmp = 0;
 	u16 eeprom_apme_mask = E1000_EEPROM_APME;
 	int bars, need_ioport;
 
@@ -996,6 +1006,14 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 		goto err_sw_init;
 
 	err = -EIO;
+	if (hw->mac_type == e1000_ce4100) {
+		ce4100_gbe_mdio_base_phy = pci_resource_start(pdev, BAR_1);
+		ce4100_gbe_mdio_base_virt = ioremap(ce4100_gbe_mdio_base_phy,
+		                                pci_resource_len(pdev, BAR_1));
+
+		if (!ce4100_gbe_mdio_base_virt)
+			goto err_mdio_ioremap;
+	}
 
 	if (hw->mac_type >= e1000_82543) {
 		netdev->features = NETIF_F_SG |
@@ -1135,6 +1153,20 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 	adapter->wol = adapter->eeprom_wol;
 	device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol);
 
+	/* Auto detect PHY address */
+	if (hw->mac_type == e1000_ce4100) {
+		for (i = 0; i < 32; i++) {
+			hw->phy_addr = i;
+			e1000_read_phy_reg(hw, PHY_ID2, &tmp);
+			if (tmp == 0 || tmp == 0xFF) {
+				if (i == 31)
+					goto err_eeprom;
+				continue;
+			} else
+				break;
+		}
+	}
+
 	/* reset the hardware with the new settings */
 	e1000_reset(adapter);
 
@@ -1171,6 +1203,8 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 	kfree(adapter->rx_ring);
 err_dma:
 err_sw_init:
+err_mdio_ioremap:
+	iounmap(ce4100_gbe_mdio_base_virt);
 	iounmap(hw->hw_addr);
 err_ioremap:
 	free_netdev(netdev);
@@ -1409,6 +1443,7 @@ static bool e1000_check_64k_bound(struct e1000_adapter *adapter, void *start,
 	/* First rev 82545 and 82546 need to not allow any memory
 	 * write location to cross 64k boundary due to errata 23 */
 	if (hw->mac_type == e1000_82545 ||
+	    hw->mac_type == e1000_ce4100 ||
 	    hw->mac_type == e1000_82546) {
 		return ((begin ^ (end - 1)) >> 16) != 0 ? false : true;
 	}

drivers/net/e1000/e1000_osdep.h

@@ -34,12 +34,21 @@
 #ifndef _E1000_OSDEP_H_
 #define _E1000_OSDEP_H_
 
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/delay.h>
 #include <asm/io.h>
-#include <linux/interrupt.h>
-#include <linux/sched.h>
+
+#define CONFIG_RAM_BASE         0x60000
+#define GBE_CONFIG_OFFSET       0x0
+
+#define GBE_CONFIG_RAM_BASE \
+	((unsigned int)(CONFIG_RAM_BASE + GBE_CONFIG_OFFSET))
+
+#define GBE_CONFIG_BASE_VIRT    phys_to_virt(GBE_CONFIG_RAM_BASE)
+
+#define GBE_CONFIG_FLASH_WRITE(base, offset, count, data) \
+	(iowrite16_rep(base + offset, data, count))
+
+#define GBE_CONFIG_FLASH_READ(base, offset, count, data) \
+	(ioread16_rep(base + (offset << 1), data, count))
 
 #define er32(reg)							\
 	(readl(hw->hw_addr + ((hw->mac_type >= e1000_82543)		\