ASoC: atmel: fix spelling mistakes

Fix some spelling mistakes as follows:
regaedles ==> regardless
prezent ==> present
underrrun ==> underrun
controlls ==> controls
Signed-off-by: Gu Shengxian <gushengxian@yulong.com>
Link: https://lore.kernel.org/r/20210706100230.32633-1-gushengxian507419@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

sound/soc/atmel/mchp-spdifrx.c

@@ -56,7 +56,7 @@
 /* Validity Bit Mode */
 #define SPDIFRX_MR_VBMODE_MASK		GENAMSK(1, 1)
 #define SPDIFRX_MR_VBMODE_ALWAYS_LOAD \
-	(0 << 1)	/* Load sample regardles of validity bit value */
+	(0 << 1)	/* Load sample regardless of validity bit value */
 #define SPDIFRX_MR_VBMODE_DISCARD_IF_VB1 \
 	(1 << 1)	/* Load sample only if validity bit is 0 */
 
@@ -519,7 +519,7 @@ static int mchp_spdifrx_cs_get(struct mchp_spdifrx_dev *dev,
 	/* check for new data available */
 	ret = wait_for_completion_interruptible_timeout(&ch_stat->done,
 							msecs_to_jiffies(100));
-	/* IP might not be started or valid stream might not be prezent */
+	/* IP might not be started or valid stream might not be present */
 	if (ret < 0) {
 		dev_dbg(dev->dev, "channel status for channel %d timeout\n",
 			channel);
@@ -571,7 +571,7 @@ static int mchp_spdifrx_subcode_ch_get(struct mchp_spdifrx_dev *dev,
 	mchp_spdifrx_isr_blockend_en(dev);
 	ret = wait_for_completion_interruptible_timeout(&user_data->done,
 							msecs_to_jiffies(100));
-	/* IP might not be started or valid stream might not be prezent */
+	/* IP might not be started or valid stream might not be present */
 	if (ret <= 0) {
 		dev_dbg(dev->dev, "user data for channel %d timeout\n",
 			channel);

sound/soc/atmel/mchp-spdiftx.c

@@ -80,7 +80,7 @@
 #define SPDIFTX_MR_VALID1			BIT(24)
 #define SPDIFTX_MR_VALID2			BIT(25)
 
-/* Disable Null Frame on underrrun */
+/* Disable Null Frame on underrun */
 #define SPDIFTX_MR_DNFR_MASK		GENMASK(27, 27)
 #define SPDIFTX_MR_DNFR_INVALID		(0 << 27)
 #define SPDIFTX_MR_DNFR_VALID		(1 << 27)

sound/soc/atmel/tse850-pcm5142.c

@@ -23,7 +23,7 @@
 //   IN2 +---o--+------------+--o---+ OUT2
 //               loop2 relays
 //
-// The 'loop1' gpio pin controlls two relays, which are either in loop
+// The 'loop1' gpio pin controls two relays, which are either in loop
 // position, meaning that input and output are directly connected, or
 // they are in mixer position, meaning that the signal is passed through
 // the 'Sum' mixer. Similarly for 'loop2'.