Merge tag 'arm-soc/for-4.11/devicetree-arm64' of http://github.com/Broadcom/stblinux into next/dt64

This pull request contains Broadcom ARM64-based SoC Device Tree changes for
4.11, please pull the following changes:

- Jon adds Device Tree nodes for the GICv2m and PAXB/PAXC PCIe interfaces on
  the Northstar 2 SoCs, he also enables PAXC on the Northstar 2 SVK reference
  board. He also updates the reserved memory entry for the Nitro firmware,
  required to get the on-chip NICs to work. Finally he adds support for the
  BCM958712DxXMC reference board which is a subset of existing boards.

* tag 'arm-soc/for-4.11/devicetree-arm64' of http://github.com/Broadcom/stblinux:
  arm64: dts: NS2: add support for XMC form factor
  arm64: dts: NS2: reserve memory for Nitro firmware
  arm64: dts: NS2: enable PAXC on NS2 SVK
  arm64: dts: NS2: enable GICv2m for PAXB/PAXC interfaces
Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm64/boot/dts/broadcom/Makefile

 dtb-$(CONFIG_ARCH_BCM2835) += bcm2837-rpi-3-b.dtb
-dtb-$(CONFIG_ARCH_BCM_IPROC) += ns2-svk.dtb
+dtb-$(CONFIG_ARCH_BCM_IPROC) += ns2-svk.dtb ns2-xmc.dtb
 dtb-$(CONFIG_ARCH_VULCAN) += vulcan-eval.dtb
 
 always		:= $(dtb-y)

arch/arm64/boot/dts/broadcom/ns2-svk.dts

@@ -76,6 +76,10 @@ &pcie4 {
 	status = "ok";
 };
 
+&pcie8 {
+	status = "ok";
+};
+
 &i2c0 {
 	status = "ok";
 };

arch/arm64/boot/dts/broadcom/ns2-xmc.dts

+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2016 Broadcom.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "ns2.dtsi"
+
+/ {
+	model = "Broadcom NS2 XMC";
+	compatible = "brcm,ns2-xmc", "brcm,ns2";
+
+	aliases {
+		serial0 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		bootargs = "earlycon=uart8250,mmio32,0x66130000";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x000000000 0x80000000 0x00000001 0x00000000>;
+	};
+};
+
+&enet {
+	status = "ok";
+};
+
+&i2c0 {
+	status = "ok";
+};
+
+&i2c1 {
+	status = "ok";
+};
+
+&mdio_mux_iproc {
+	mdio@10 {
+		gphy0: eth-phy@10 {
+			reg = <0x10>;
+		};
+	};
+};
+
+&nand {
+	nandcs@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-ecc-mode = "hw";
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <16>;
+		brcm,nand-oob-sector-size = <16>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "nboot";
+			reg = <0x00000000 0x00280000>; /*  2.5MB */
+			read-only;
+		};
+
+		partition@280000 {
+			label = "nenv";
+			reg = <0x00280000 0x00040000>; /* 0.25MB */
+			read-only;
+		};
+
+		partition@2c0000 {
+			label = "ndtb";
+			reg = <0x002c0000 0x00040000>; /* 0.25MB */
+			read-only;
+		};
+
+		partition@300000 {
+			label = "nsystem";
+			reg = <0x00300000 0x03d00000>; /*   61MB */
+			read-only;
+		};
+
+		partition@4000000 {
+			label = "nrootfs";
+			reg = <0x04000000 0x06400000>; /*  100MB */
+		};
+
+		partition@0a400000{
+			label = "ncustfs";
+			reg = <0x0a400000 0x35c00000>; /*  860MB */
+		};
+	};
+};
+
+&pci_phy0 {
+	status = "ok";
+};
+
+&pcie0 {
+	status = "ok";
+};
+
+&pcie8 {
+	status = "ok";
+};
+
+&sata_phy0 {
+	status = "ok";
+};
+
+&sata_phy1 {
+	status = "ok";
+};
+
+&sata {
+	status = "ok";
+};
+
+&qspi {
+	flash: m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80";
+		spi-max-frequency = <62500000>;
+		m25p,default-addr-width = <3>;
+		reg = <0x0 0x0>;
+
+		partition@0 {
+			label = "bl0";
+			reg = <0x00000000 0x00080000>; /*  512KB */
+		};
+
+		partition@80000 {
+			label = "fip";
+			reg = <0x00080000 0x00150000>; /* 1344KB */
+		};
+
+		partition@1e0000 {
+			label = "env";
+			reg = <0x001e0000 0x00010000>;/*    64KB */
+		};
+
+		partition@1f0000 {
+			label = "dtb";
+			reg = <0x001f0000 0x00010000>; /*   64KB */
+		};
+
+		partition@200000 {
+			label = "kernel";
+			reg = <0x00200000 0x00e00000>; /*   14MB */
+		};
+
+		partition@1000000 {
+			label = "rootfs";
+			reg = <0x01000000 0x01000000>; /*   16MB */
+		};
+	};
+};
+
+&uart3 {
+	status = "ok";
+};

arch/arm64/boot/dts/broadcom/ns2.dtsi

@@ -30,6 +30,8 @@
  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  */
 
+/memreserve/ 0x81000000 0x00200000;
+
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/bcm-ns2.h>
 
@@ -115,7 +117,7 @@ pcie0: pcie@20020000 {
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 281 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 281 IRQ_TYPE_NONE>;
 
 		linux,pci-domain = <0>;
 
@@ -136,18 +138,7 @@ pcie0: pcie@20020000 {
 		phys = <&pci_phy0>;
 		phy-names = "pcie-phy";
 
-		msi-parent = <&msi0>;
-		msi0: msi@20020000 {
-			compatible = "brcm,iproc-msi";
-			msi-controller;
-			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 277 IRQ_TYPE_NONE>,
-				     <GIC_SPI 278 IRQ_TYPE_NONE>,
-				     <GIC_SPI 279 IRQ_TYPE_NONE>,
-				     <GIC_SPI 280 IRQ_TYPE_NONE>;
-			brcm,num-eq-region = <1>;
-			brcm,num-msi-msg-region = <1>;
-		};
+		msi-parent = <&v2m0>;
 	};
 
 	pcie4: pcie@50020000 {
@@ -156,7 +147,7 @@ pcie4: pcie@50020000 {
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 305 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 305 IRQ_TYPE_NONE>;
 
 		linux,pci-domain = <4>;
 
@@ -177,16 +168,24 @@ pcie4: pcie@50020000 {
 		phys = <&pci_phy1>;
 		phy-names = "pcie-phy";
 
-		msi-parent = <&msi4>;
-		msi4: msi@50020000 {
-			compatible = "brcm,iproc-msi";
-			msi-controller;
-			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 301 IRQ_TYPE_NONE>,
-				     <GIC_SPI 302 IRQ_TYPE_NONE>,
-				     <GIC_SPI 303 IRQ_TYPE_NONE>,
-				     <GIC_SPI 304 IRQ_TYPE_NONE>;
-		};
+		msi-parent = <&v2m0>;
+	};
+
+	pcie8: pcie@60c00000 {
+		compatible = "brcm,iproc-pcie-paxc";
+		reg = <0 0x60c00000 0 0x1000>;
+		linux,pci-domain = <8>;
+
+		bus-range = <0x0 0x1>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		ranges = <0x83000000 0 0x00000000 0 0x60000000 0 0x00c00000>;
+
+		status = "disabled";
+
+		msi-parent = <&v2m0>;
 	};
 
 	soc: soc {
@@ -331,6 +330,82 @@ gic: interrupt-controller@65210000 {
 			      <0x65260000 0x1000>;
 			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_RAW(0xf) |
 				      IRQ_TYPE_LEVEL_HIGH)>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x652e0000 0x80000>;
+
+			v2m0: v2m@00000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x00000 0x1000>;
+				arm,msi-base-spi = <72>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m1: v2m@10000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x10000 0x1000>;
+				arm,msi-base-spi = <88>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m2: v2m@20000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x20000 0x1000>;
+				arm,msi-base-spi = <104>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m3: v2m@30000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x30000 0x1000>;
+				arm,msi-base-spi = <120>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m4: v2m@40000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x40000 0x1000>;
+				arm,msi-base-spi = <136>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m5: v2m@50000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x50000 0x1000>;
+				arm,msi-base-spi = <152>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m6: v2m@60000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x60000 0x1000>;
+				arm,msi-base-spi = <168>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m7: v2m@70000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x70000 0x1000>;
+				arm,msi-base-spi = <184>;
+				arm,msi-num-spis = <16>;
+			};
 		};
 
 		cci@65590000 {