Add 85xx CDS to arch/powerpc

This patch adds support for 85xx CDS support to arch/powerpc
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

arch/powerpc/platforms/85xx/Kconfig

@@ -11,13 +11,20 @@ config MPC8540_ADS
 	help
 	  This option enables support for the MPC 8540 ADS board
 
+config MPC85xx_CDS
+	bool "Freescale MPC85xx CDS"
+	select DEFAULT_UIMAGE
+	select PPC_I8259 if PCI
+	help
+	  This option enables support for the MPC85xx CDS board
+
 endchoice
 
 config MPC8540
 	bool
 	select PPC_UDBG_16550
 	select PPC_INDIRECT_PCI
-	default y if MPC8540_ADS
+	default y if MPC8540_ADS || MPC85xx_CDS
 
 config PPC_INDIRECT_PCI_BE
 	bool

arch/powerpc/platforms/85xx/Makefile

@@ -3,3 +3,4 @@
 #
 obj-$(CONFIG_PPC_85xx)	+= misc.o pci.o
 obj-$(CONFIG_MPC8540_ADS) += mpc85xx_ads.o
+obj-$(CONFIG_MPC85xx_CDS) += mpc85xx_cds.o

arch/powerpc/platforms/85xx/mpc85xx_cds.c

+/*
+ * MPC85xx setup and early boot code plus other random bits.
+ *
+ * Maintained by Kumar Gala (see MAINTAINERS for contact information)
+ *
+ * Copyright 2005 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/config.h>
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/reboot.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/major.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/seq_file.h>
+#include <linux/root_dev.h>
+#include <linux/initrd.h>
+#include <linux/module.h>
+#include <linux/fsl_devices.h>
+
+#include <asm/system.h>
+#include <asm/pgtable.h>
+#include <asm/page.h>
+#include <asm/atomic.h>
+#include <asm/time.h>
+#include <asm/io.h>
+#include <asm/machdep.h>
+#include <asm/ipic.h>
+#include <asm/bootinfo.h>
+#include <asm/pci-bridge.h>
+#include <asm/mpc85xx.h>
+#include <asm/irq.h>
+#include <mm/mmu_decl.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/mpic.h>
+#include <asm/i8259.h>
+
+#include <sysdev/fsl_soc.h>
+#include "mpc85xx.h"
+
+#ifndef CONFIG_PCI
+unsigned long isa_io_base = 0;
+unsigned long isa_mem_base = 0;
+#endif
+
+static int cds_pci_slot = 2;
+static volatile u8 *cadmus;
+
+/*
+ * Internal interrupts are all Level Sensitive, and Positive Polarity
+ *
+ * Note:  Likely, this table and the following function should be
+ *        obtained and derived from the OF Device Tree.
+ */
+static u_char mpc85xx_cds_openpic_initsenses[] __initdata = {
+	MPC85XX_INTERNAL_IRQ_SENSES,
+#if defined(CONFIG_PCI)
+	(IRQ_SENSE_LEVEL | IRQ_POLARITY_POSITIVE),	/* Ext 0: PCI slot 0 */
+	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),	/* Ext 1: PCI slot 1 */
+	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),	/* Ext 2: PCI slot 2 */
+	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),	/* Ext 3: PCI slot 3 */
+#else
+	0x0,				/* External  0: */
+	0x0,				/* External  1: */
+	0x0,				/* External  2: */
+	0x0,				/* External  3: */
+#endif
+	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),	/* External 5: PHY */
+	0x0,				/* External  6: */
+	0x0,				/* External  7: */
+	0x0,				/* External  8: */
+	0x0,				/* External  9: */
+	0x0,				/* External 10: */
+#ifdef CONFIG_PCI
+	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),    /* Ext 11: PCI2 slot 0 */
+#else
+	0x0,				/* External 11: */
+#endif
+};
+
+
+#ifdef CONFIG_PCI
+/*
+ * interrupt routing
+ */
+int
+mpc85xx_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin)
+{
+	struct pci_controller *hose = pci_bus_to_hose(dev->bus->number);
+
+	if (!hose->index)
+	{
+		/* Handle PCI1 interrupts */
+		char pci_irq_table[][4] =
+			/*
+			 *      PCI IDSEL/INTPIN->INTLINE
+			 *        A      B      C      D
+			 */
+
+			/* Note IRQ assignment for slots is based on which slot the elysium is
+			 * in -- in this setup elysium is in slot #2 (this PIRQA as first
+			 * interrupt on slot */
+		{
+			{ 0, 1, 2, 3 }, /* 16 - PMC */
+			{ 0, 1, 2, 3 }, /* 17 P2P (Tsi320) */
+			{ 0, 1, 2, 3 }, /* 18 - Slot 1 */
+			{ 1, 2, 3, 0 }, /* 19 - Slot 2 */
+			{ 2, 3, 0, 1 }, /* 20 - Slot 3 */
+			{ 3, 0, 1, 2 }, /* 21 - Slot 4 */
+		};
+
+		const long min_idsel = 16, max_idsel = 21, irqs_per_slot = 4;
+		int i, j;
+
+		for (i = 0; i < 6; i++)
+			for (j = 0; j < 4; j++)
+				pci_irq_table[i][j] =
+					((pci_irq_table[i][j] + 5 -
+					  cds_pci_slot) & 0x3) + PIRQ0A;
+
+		return PCI_IRQ_TABLE_LOOKUP;
+	} else {
+		/* Handle PCI2 interrupts (if we have one) */
+		char pci_irq_table[][4] =
+		{
+			/*
+			 * We only have one slot and one interrupt
+			 * going to PIRQA - PIRQD */
+			{ PIRQ1A, PIRQ1A, PIRQ1A, PIRQ1A }, /* 21 - slot 0 */
+		};
+
+		const long min_idsel = 21, max_idsel = 21, irqs_per_slot = 4;
+
+		return PCI_IRQ_TABLE_LOOKUP;
+	}
+}
+
+#define ARCADIA_HOST_BRIDGE_IDSEL	17
+#define ARCADIA_2ND_BRIDGE_IDSEL	3
+
+extern int mpc85xx_pci2_busno;
+
+int
+mpc85xx_exclude_device(u_char bus, u_char devfn)
+{
+	if (bus == 0 && PCI_SLOT(devfn) == 0)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+	if (mpc85xx_pci2_busno)
+		if (bus == (mpc85xx_pci2_busno) && PCI_SLOT(devfn) == 0)
+			return PCIBIOS_DEVICE_NOT_FOUND;
+	/* We explicitly do not go past the Tundra 320 Bridge */
+	if ((bus == 1) && (PCI_SLOT(devfn) == ARCADIA_2ND_BRIDGE_IDSEL))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+	if ((bus == 0) && (PCI_SLOT(devfn) == ARCADIA_2ND_BRIDGE_IDSEL))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+	else
+		return PCIBIOS_SUCCESSFUL;
+}
+
+void __init
+mpc85xx_cds_pcibios_fixup(void)
+{
+	struct pci_dev *dev;
+	u_char		c;
+
+	if ((dev = pci_get_device(PCI_VENDOR_ID_VIA,
+					PCI_DEVICE_ID_VIA_82C586_1, NULL))) {
+		/*
+		 * U-Boot does not set the enable bits
+		 * for the IDE device. Force them on here.
+		 */
+		pci_read_config_byte(dev, 0x40, &c);
+		c |= 0x03; /* IDE: Chip Enable Bits */
+		pci_write_config_byte(dev, 0x40, c);
+
+		/*
+		 * Since only primary interface works, force the
+		 * IDE function to standard primary IDE interrupt
+		 * w/ 8259 offset
+		 */
+		dev->irq = 14;
+		pci_write_config_byte(dev, PCI_INTERRUPT_LINE, dev->irq);
+		pci_dev_put(dev);
+	}
+
+	/*
+	 * Force legacy USB interrupt routing
+	 */
+	if ((dev = pci_get_device(PCI_VENDOR_ID_VIA,
+					PCI_DEVICE_ID_VIA_82C586_2, NULL))) {
+		dev->irq = 10;
+		pci_write_config_byte(dev, PCI_INTERRUPT_LINE, 10);
+		pci_dev_put(dev);
+	}
+
+	if ((dev = pci_get_device(PCI_VENDOR_ID_VIA,
+					PCI_DEVICE_ID_VIA_82C586_2, dev))) {
+		dev->irq = 11;
+		pci_write_config_byte(dev, PCI_INTERRUPT_LINE, 11);
+		pci_dev_put(dev);
+	}
+}
+#endif /* CONFIG_PCI */
+
+void __init mpc85xx_cds_pic_init(void)
+{
+	struct mpic *mpic1;
+	phys_addr_t OpenPIC_PAddr;
+
+	/* Determine the Physical Address of the OpenPIC regs */
+	OpenPIC_PAddr = get_immrbase() + MPC85xx_OPENPIC_OFFSET;
+
+	mpic1 = mpic_alloc(OpenPIC_PAddr,
+			MPIC_PRIMARY | MPIC_WANTS_RESET | MPIC_BIG_ENDIAN,
+			4, MPC85xx_OPENPIC_IRQ_OFFSET, 0, 250,
+			mpc85xx_cds_openpic_initsenses,
+			sizeof(mpc85xx_cds_openpic_initsenses), " OpenPIC  ");
+	BUG_ON(mpic1 == NULL);
+	mpic_assign_isu(mpic1, 0, OpenPIC_PAddr + 0x10200);
+	mpic_assign_isu(mpic1, 1, OpenPIC_PAddr + 0x10280);
+	mpic_assign_isu(mpic1, 2, OpenPIC_PAddr + 0x10300);
+	mpic_assign_isu(mpic1, 3, OpenPIC_PAddr + 0x10380);
+	mpic_assign_isu(mpic1, 4, OpenPIC_PAddr + 0x10400);
+	mpic_assign_isu(mpic1, 5, OpenPIC_PAddr + 0x10480);
+	mpic_assign_isu(mpic1, 6, OpenPIC_PAddr + 0x10500);
+	mpic_assign_isu(mpic1, 7, OpenPIC_PAddr + 0x10580);
+
+	/* dummy mappings to get to 48 */
+	mpic_assign_isu(mpic1, 8, OpenPIC_PAddr + 0x10600);
+	mpic_assign_isu(mpic1, 9, OpenPIC_PAddr + 0x10680);
+	mpic_assign_isu(mpic1, 10, OpenPIC_PAddr + 0x10700);
+	mpic_assign_isu(mpic1, 11, OpenPIC_PAddr + 0x10780);
+
+	/* External ints */
+	mpic_assign_isu(mpic1, 12, OpenPIC_PAddr + 0x10000);
+	mpic_assign_isu(mpic1, 13, OpenPIC_PAddr + 0x10080);
+	mpic_assign_isu(mpic1, 14, OpenPIC_PAddr + 0x10100);
+
+	mpic_init(mpic1);
+
+#ifdef CONFIG_PCI
+	mpic_setup_cascade(PIRQ0A, i8259_irq_cascade, NULL);
+
+	i8259_init(0,0);
+#endif
+}
+
+
+/*
+ * Setup the architecture
+ */
+static void __init
+mpc85xx_cds_setup_arch(void)
+{
+	struct device_node *cpu;
+#ifdef CONFIG_PCI
+	struct device_node *np;
+#endif
+
+	if (ppc_md.progress)
+		ppc_md.progress("mpc85xx_cds_setup_arch()", 0);
+
+	cpu = of_find_node_by_type(NULL, "cpu");
+	if (cpu != 0) {
+		unsigned int *fp;
+
+		fp = (int *)get_property(cpu, "clock-frequency", NULL);
+		if (fp != 0)
+			loops_per_jiffy = *fp / HZ;
+		else
+			loops_per_jiffy = 500000000 / HZ;
+		of_node_put(cpu);
+	}
+
+	cadmus = ioremap(CADMUS_BASE, CADMUS_SIZE);
+	cds_pci_slot = ((cadmus[CM_CSR] >> 6) & 0x3) + 1;
+
+	if (ppc_md.progress) {
+		char buf[40];
+		snprintf(buf, 40, "CDS Version = 0x%x in slot %d\n",
+				cadmus[CM_VER], cds_pci_slot);
+		ppc_md.progress(buf, 0);
+	}
+
+#ifdef CONFIG_PCI
+	for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;)
+		add_bridge(np);
+
+	ppc_md.pcibios_fixup = mpc85xx_cds_pcibios_fixup;
+	ppc_md.pci_swizzle = common_swizzle;
+	ppc_md.pci_map_irq = mpc85xx_map_irq;
+	ppc_md.pci_exclude_device = mpc85xx_exclude_device;
+#endif
+
+#ifdef  CONFIG_ROOT_NFS
+	ROOT_DEV = Root_NFS;
+#else
+	ROOT_DEV = Root_HDA1;
+#endif
+}
+
+
+void
+mpc85xx_cds_show_cpuinfo(struct seq_file *m)
+{
+	uint pvid, svid, phid1;
+	uint memsize = total_memory;
+
+	pvid = mfspr(SPRN_PVR);
+	svid = mfspr(SPRN_SVR);
+
+	seq_printf(m, "Vendor\t\t: Freescale Semiconductor\n");
+	seq_printf(m, "Machine\t\t: MPC85xx CDS (0x%x)\n", cadmus[CM_VER]);
+	seq_printf(m, "PVR\t\t: 0x%x\n", pvid);
+	seq_printf(m, "SVR\t\t: 0x%x\n", svid);
+
+	/* Display cpu Pll setting */
+	phid1 = mfspr(SPRN_HID1);
+	seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f));
+
+	/* Display the amount of memory */
+	seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
+}
+
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init mpc85xx_cds_probe(void)
+{
+	/* We always match for now, eventually we should look at
+	 * the flat dev tree to ensure this is the board we are
+	 * supposed to run on
+	 */
+	return 1;
+}
+
+define_machine(mpc85xx_cds) {
+	.name		= "MPC85xx CDS",
+	.probe		= mpc85xx_cds_probe,
+	.setup_arch	= mpc85xx_cds_setup_arch,
+	.init_IRQ	= mpc85xx_cds_pic_init,
+	.show_cpuinfo	= mpc85xx_cds_show_cpuinfo,
+	.get_irq	= mpic_get_irq,
+	.restart	= mpc85xx_restart,
+	.calibrate_decr = generic_calibrate_decr,
+	.progress	= udbg_progress,
+};

arch/powerpc/platforms/85xx/mpc85xx_cds.h

+/*
+ * arch/ppc/platforms/85xx/mpc85xx_cds_common.h
+ *
+ * MPC85xx CDS board definitions
+ *
+ * Maintainer: Kumar Gala <galak@kernel.crashing.org>
+ *
+ * Copyright 2004 Freescale Semiconductor, Inc
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+
+#ifndef __MACH_MPC85XX_CDS_H__
+#define __MACH_MPC85XX_CDS_H__
+
+/* CADMUS info */
+#define CADMUS_BASE (0xf8004000)
+#define CADMUS_SIZE (256)
+#define CM_VER	(0)
+#define CM_CSR	(1)
+#define CM_RST	(2)
+
+/* CDS NVRAM/RTC */
+#define CDS_RTC_ADDR	(0xf8000000)
+#define CDS_RTC_SIZE	(8 * 1024)
+
+/* PCI interrupt controller */
+#define PIRQ0A			MPC85xx_IRQ_EXT0
+#define PIRQ0B			MPC85xx_IRQ_EXT1
+#define PIRQ0C			MPC85xx_IRQ_EXT2
+#define PIRQ0D			MPC85xx_IRQ_EXT3
+#define PIRQ1A			MPC85xx_IRQ_EXT11
+
+#define NR_8259_INTS		16
+#define CPM_IRQ_OFFSET		NR_8259_INTS
+
+#define MPC85xx_OPENPIC_IRQ_OFFSET	80
+
+#endif /* __MACH_MPC85XX_CDS_H__ */

include/asm-ppc/mpc85xx.h

@@ -28,6 +28,9 @@
 #if defined(CONFIG_MPC8555_CDS) || defined(CONFIG_MPC8548_CDS)
 #include <platforms/85xx/mpc8555_cds.h>
 #endif
+#ifdef CONFIG_MPC85xx_CDS
+#include <platforms/85xx/mpc85xx_cds.h>
+#endif
 #ifdef CONFIG_MPC8560_ADS
 #include <platforms/85xx/mpc8560_ads.h>
 #endif