soc: aspeed: Improve kconfig

Reword the kconfig text to be consistent and reflect that most drivers
are available for all supported ASPEED chips (2400, 2500 and 2600).

Rearrange the symbols the SoC drivers depend on so the menu doesn't
appear unless you are building for ASPEED for compile testing.

The SYSCON_MFD and REGMAP options are usually selected by drivers that
need them, so do this.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20200916125731.784527-1-joel@jms.id.auSigned-off-by: Joel Stanley <joel@jms.id.au>

drivers/soc/Makefile

@@ -4,7 +4,7 @@
 #
 
 obj-$(CONFIG_ARCH_ACTIONS)	+= actions/
-obj-$(CONFIG_SOC_ASPEED)	+= aspeed/
+obj-y				+= aspeed/
 obj-$(CONFIG_ARCH_AT91)		+= atmel/
 obj-y				+= bcm/
 obj-$(CONFIG_ARCH_DOVE)		+= dove/

drivers/soc/aspeed/Kconfig

 # SPDX-License-Identifier: GPL-2.0-only
-menu "Aspeed SoC drivers"
 
-config SOC_ASPEED
-	def_bool y
-	depends on ARCH_ASPEED || COMPILE_TEST
+if ARCH_ASPEED || COMPILE_TEST
+
+menu "ASPEED SoC drivers"
 
 config ASPEED_LPC_CTRL
-	depends on SOC_ASPEED && REGMAP && MFD_SYSCON
-	tristate "Aspeed ast2400/2500 HOST LPC to BMC bridge control"
+	tristate "ASPEED LPC firmware cycle control"
+	select REGMAP
+	select MFD_SYSCON
 	help
-	  Control Aspeed ast2400/2500 HOST LPC to BMC mappings through
-	  ioctl()s, the driver also provides a read/write interface to a BMC ram
-	  region where the host LPC read/write region can be buffered.
+	  Control LPC firmware cycle mappings through ioctl()s. The driver
+	  also provides a read/write interface to a BMC ram region where the
+	  host LPC read/write region can be buffered.
 
 config ASPEED_LPC_SNOOP
-	tristate "Aspeed ast2500 HOST LPC snoop support"
-	depends on SOC_ASPEED && REGMAP && MFD_SYSCON
+	tristate "ASPEED LPC snoop support"
+	select REGMAP
+	select MFD_SYSCON
 	help
 	  Provides a driver to control the LPC snoop interface which
 	  allows the BMC to listen on and save the data written by
 	  the host to an arbitrary LPC I/O port.
 
 config ASPEED_P2A_CTRL
-	depends on SOC_ASPEED && REGMAP && MFD_SYSCON
-	tristate "Aspeed ast2400/2500 HOST P2A VGA MMIO to BMC bridge control"
+	tristate "ASPEED P2A (VGA MMIO to BMC) bridge control"
+	select REGMAP
+	select MFD_SYSCON
 	help
-	  Control Aspeed ast2400/2500 HOST P2A VGA MMIO to BMC mappings through
-	  ioctl()s, the driver also provides an interface for userspace mappings to
-	  a pre-defined region.
+	  Control ASPEED P2A VGA MMIO to BMC mappings through ioctl()s.  The
+	  driver also provides an interface for userspace mappings to a
+	  pre-defined region.
 
 endmenu
+
+endif