Commit 5a0f93c6 authored by Nishanth Menon's avatar Nishanth Menon Committed by Tony Lindgren

ARM: dts: Add am57xx-beagle-x15

BeagleBoard-X15 is the next generation Open Source Hardware
BeagleBoard based on TI's AM5728 SoC featuring dual core 1.5GHz A15
processor. The platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x1080@60), separate LCD
port, video In port, 4GB eMMC, uSD, Analog audio in/out, dual 1G
Ethernet.

For more information, refer to:
BeagleBoard-X15 Wiki:
http://www.elinux.org/Beagleboard:BeagleBoard-X15

AM5728 is part of the Sitara product family whose additional details
will be available: http://www.ti.com/lsds/ti/arm/overview.page

Technical Reference Manual for AM5728 is public domain at:
http://www.ti.com/lit/spruhz6

Just add basic support for the moment, the following updates are needed:
  i)	Ethernet - depends on SoC dts fixes
  ii)	USB Client (USB2) - depends on GPIO extcon
  ii)	HDMI - additional driver fixes pending
  iii)	Audio - additional driver fixes pending

NOTE:
AM5728 Data Manual (SPRS915L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions". This implies
that all unused voltage rails for AM5728 can never be switched off even
if the hardware blocks inside that voltage domain is unused. Switching
off these unused rails may result in stability issues on other domains
and increased leakage and power-on-hour impacts.
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
Signed-off-by: default avatarNishanth Menon <nm@ti.com>
Reviewed-by: default avatarTom Rini <trini@ti.com>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
parent d565b5f4
...@@ -349,6 +349,7 @@ dtb-$(CONFIG_SOC_OMAP5) += omap5-cm-t54.dtb \ ...@@ -349,6 +349,7 @@ dtb-$(CONFIG_SOC_OMAP5) += omap5-cm-t54.dtb \
omap5-sbc-t54.dtb \ omap5-sbc-t54.dtb \
omap5-uevm.dtb omap5-uevm.dtb
dtb-$(CONFIG_SOC_DRA7XX) += dra7-evm.dtb \ dtb-$(CONFIG_SOC_DRA7XX) += dra7-evm.dtb \
am57xx-beagle-x15.dtb \
dra72-evm.dtb dra72-evm.dtb
dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-d2-network.dtb \ dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-d2-network.dtb \
orion5x-lacie-ethernet-disk-mini-v2.dtb \ orion5x-lacie-ethernet-disk-mini-v2.dtb \
......
/*
* Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/dts-v1/;
#include "dra74x.dtsi"
#include <dt-bindings/clk/ti-dra7-atl.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "TI AM5728 BeagleBoard-X15";
compatible = "ti,am572x-beagle-x15", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7";
aliases {
rtc0 = &mcp_rtc;
rtc1 = &tps659038_rtc;
};
memory {
device_type = "memory";
reg = <0x80000000 0x80000000>;
};
vdd_3v3: fixedregulator-vdd_3v3 {
compatible = "regulator-fixed";
regulator-name = "vdd_3v3";
vin-supply = <&regen1>;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vtt_fixed: fixedregulator-vtt {
/* TPS51200 */
compatible = "regulator-fixed";
regulator-name = "vtt_fixed";
vin-supply = <&smps3_reg>;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-boot-on;
enable-active-high;
gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&leds_pins_default>;
led@0 {
label = "beagle-x15:usr0";
gpios = <&gpio7 9 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
default-state = "off";
};
led@1 {
label = "beagle-x15:usr1";
gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "cpu0";
default-state = "off";
};
led@2 {
label = "beagle-x15:usr2";
gpios = <&gpio7 14 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "mmc0";
default-state = "off";
};
led@3 {
label = "beagle-x15:usr3";
gpios = <&gpio7 15 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "ide-disk";
default-state = "off";
};
};
};
&dra7_pmx_core {
leds_pins_default: leds_pins_default {
pinctrl-single,pins = <
0x3a8 (PIN_OUTPUT | MUX_MODE14) /* spi1_d1.gpio7_8 */
0x3ac (PIN_OUTPUT | MUX_MODE14) /* spi1_d0.gpio7_9 */
0x3c0 (PIN_OUTPUT | MUX_MODE14) /* spi2_sclk.gpio7_14 */
0x3c4 (PIN_OUTPUT | MUX_MODE14) /* spi2_d1.gpio7_15 */
>;
};
i2c1_pins_default: i2c1_pins_default {
pinctrl-single,pins = <
0x400 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda.sda */
0x404 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl.scl */
>;
};
i2c3_pins_default: i2c3_pins_default {
pinctrl-single,pins = <
0x2a4 (PIN_INPUT| MUX_MODE10) /* mcasp1_aclkx.i2c3_sda */
0x2a8 (PIN_INPUT| MUX_MODE10) /* mcasp1_fsx.i2c3_scl */
>;
};
uart3_pins_default: uart3_pins_default {
pinctrl-single,pins = <
0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd.rxd */
0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd.txd */
>;
};
mmc1_pins_default: mmc1_pins_default {
pinctrl-single,pins = <
0x36c (PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */
0x354 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
0x358 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
0x35c (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
0x360 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
0x364 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
0x368 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
>;
};
mmc2_pins_default: mmc2_pins_default {
pinctrl-single,pins = <
0x9c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
0xb0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
0xa0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
0xa4 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
0xa8 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
0xac (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
0x8c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
0x90 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
0x94 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
0x98 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
>;
};
tps659038_pins_default: tps659038_pins_default {
pinctrl-single,pins = <
0x418 (PIN_INPUT_PULLUP | MUX_MODE14) /* wakeup0.gpio1_0 */
>;
};
tmp102_pins_default: tmp102_pins_default {
pinctrl-single,pins = <
0x3C8 (PIN_INPUT_PULLUP | MUX_MODE14) /* spi2_d0.gpio7_16 */
>;
};
mcp79410_pins_default: mcp79410_pins_default {
pinctrl-single,pins = <
0x424 (PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */
>;
};
usb1_pins: pinmux_usb1_pins {
pinctrl-single,pins = <
0x280 (PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
>;
};
};
&i2c1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_default>;
clock-frequency = <400000>;
tps659038: tps659038@58 {
compatible = "ti,tps659038";
reg = <0x58>;
interrupt-parent = <&gpio1>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&tps659038_pins_default>;
#interrupt-cells = <2>;
interrupt-controller;
ti,system-power-controller;
tps659038_pmic {
compatible = "ti,tps659038-pmic";
regulators {
smps12_reg: smps12 {
/* VDD_MPU */
regulator-name = "smps12";
regulator-min-microvolt = < 850000>;
regulator-max-microvolt = <1250000>;
regulator-always-on;
regulator-boot-on;
};
smps3_reg: smps3 {
/* VDD_DDR */
regulator-name = "smps3";
regulator-min-microvolt = <1350000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-boot-on;
};
smps45_reg: smps45 {
/* VDD_DSPEVE, VDD_IVA, VDD_GPU */
regulator-name = "smps45";
regulator-min-microvolt = < 850000>;
regulator-max-microvolt = <1150000>;
regulator-always-on;
regulator-boot-on;
};
smps6_reg: smps6 {
/* VDD_CORE */
regulator-name = "smps6";
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <1030000>;
regulator-always-on;
regulator-boot-on;
};
/* SMPS7 unused */
smps8_reg: smps8 {
/* VDD_1V8 */
regulator-name = "smps8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
/* SMPS9 unused */
ldo1_reg: ldo1 {
/* VDD_SD */
regulator-name = "ldo1";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
};
ldo2_reg: ldo2 {
/* VDD_SHV5 */
regulator-name = "ldo2";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-boot-on;
};
ldo3_reg: ldo3 {
/* VDDA_1V8_PHY */
regulator-name = "ldo3";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
ldo9_reg: ldo9 {
/* VDD_RTC */
regulator-name = "ldo9";
regulator-min-microvolt = <1050000>;
regulator-max-microvolt = <1050000>;
regulator-always-on;
regulator-boot-on;
};
ldoln_reg: ldoln {
/* VDDA_1V8_PLL */
regulator-name = "ldoln";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
ldousb_reg: ldousb {
/* VDDA_3V_USB: VDDA_USBHS33 */
regulator-name = "ldousb";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
};
regen1: regen1 {
/* VDD_3V3_ON */
regulator-name = "regen1";
regulator-boot-on;
regulator-always-on;
};
};
};
tps659038_rtc: tps659038_rtc {
compatible = "ti,palmas-rtc";
interrupt-parent = <&tps659038>;
interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
wakeup-source;
};
tps659038_pwr_button: tps659038_pwr_button {
compatible = "ti,palmas-pwrbutton";
interrupt-parent = <&tps659038>;
interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
wakeup-source;
ti,palmas-long-press-seconds = <12>;
};
};
tmp102: tmp102@48 {
compatible = "ti,tmp102";
reg = <0x48>;
pinctrl-names = "default";
pinctrl-0 = <&tmp102_pins_default>;
interrupt-parent = <&gpio7>;
interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
};
};
&i2c3 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c3_pins_default>;
clock-frequency = <400000>;
mcp_rtc: rtc@6f {
compatible = "microchip,mcp7941x";
reg = <0x6f>;
interrupt-parent = <&gic>;
interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_LOW>; /* IRQ_SYS_1N */
pinctrl-names = "default";
pinctrl-0 = <&mcp79410_pins_default>;
vcc-supply = <&vdd_3v3>;
wakeup-source;
};
};
&gpio7 {
ti,no-reset-on-init;
ti,no-idle-on-init;
};
&cpu0 {
cpu0-supply = <&smps12_reg>;
voltage-tolerance = <1>;
};
&uart3 {
status = "okay";
interrupts-extended = <&gic GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
<&dra7_pmx_core 0x248>;
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins_default>;
};
&mmc1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins_default>;
vmmc-supply = <&ldo1_reg>;
vmmc_aux-supply = <&vdd_3v3>;
pbias-supply = <&pbias_mmc_reg>;
bus-width = <4>;
cd-gpios = <&gpio6 27 0>; /* gpio 219 */
};
&mmc2 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins_default>;
vmmc-supply = <&vdd_3v3>;
bus-width = <8>;
ti,non-removable;
cap-mmc-dual-data-rate;
};
&sata {
status = "okay";
};
&usb2_phy1 {
phy-supply = <&ldousb_reg>;
};
&usb1 {
dr_mode = "host";
pinctrl-names = "default";
pinctrl-0 = <&usb1_pins>;
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment