Merge branch 'musb-v2.6.37-rc2' of git://gitorious.org/usb/usb into work-linus

drivers/usb/musb/blackfin.c

@@ -171,8 +171,9 @@ static irqreturn_t blackfin_interrupt(int irq, void *__hci)
 	}
 
 	/* Start sampling ID pin, when plug is removed from MUSB */
-	if (is_otg_enabled(musb) && (musb->xceiv->state == OTG_STATE_B_IDLE
-		|| musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) {
+	if ((is_otg_enabled(musb) && (musb->xceiv->state == OTG_STATE_B_IDLE
+		|| musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) ||
+		(musb->int_usb & MUSB_INTR_DISCONNECT && is_host_active(musb))) {
 		mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
 		musb->a_wait_bcon = TIMER_DELAY;
 	}
@@ -323,30 +324,8 @@ int musb_platform_set_mode(struct musb *musb, u8 musb_mode)
 	return -EIO;
 }
 
-int __init musb_platform_init(struct musb *musb, void *board_data)
+static void musb_platform_reg_init(struct musb *musb)
 {
-
-	/*
-	 * Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE
-	 * and OTG HOST modes, while rev 1.1 and greater require PE7 to
-	 * be low for DEVICE mode and high for HOST mode. We set it high
-	 * here because we are in host mode
-	 */
-
-	if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) {
-		printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d \n",
-			musb->config->gpio_vrsel);
-		return -ENODEV;
-	}
-	gpio_direction_output(musb->config->gpio_vrsel, 0);
-
-	usb_nop_xceiv_register();
-	musb->xceiv = otg_get_transceiver();
-	if (!musb->xceiv) {
-		gpio_free(musb->config->gpio_vrsel);
-		return -ENODEV;
-	}
-
 	if (ANOMALY_05000346) {
 		bfin_write_USB_APHY_CALIB(ANOMALY_05000346_value);
 		SSYNC();
@@ -358,7 +337,8 @@ int __init musb_platform_init(struct musb *musb, void *board_data)
 	}
 
 	/* Configure PLL oscillator register */
-	bfin_write_USB_PLLOSC_CTRL(0x30a8);
+	bfin_write_USB_PLLOSC_CTRL(0x3080 |
+			((480/musb->config->clkin) << 1));
 	SSYNC();
 
 	bfin_write_USB_SRP_CLKDIV((get_sclk()/1000) / 32 - 1);
@@ -380,6 +360,33 @@ int __init musb_platform_init(struct musb *musb, void *board_data)
 				EP2_RX_ENA | EP3_RX_ENA | EP4_RX_ENA |
 				EP5_RX_ENA | EP6_RX_ENA | EP7_RX_ENA);
 	SSYNC();
+}
+
+int __init musb_platform_init(struct musb *musb, void *board_data)
+{
+
+	/*
+	 * Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE
+	 * and OTG HOST modes, while rev 1.1 and greater require PE7 to
+	 * be low for DEVICE mode and high for HOST mode. We set it high
+	 * here because we are in host mode
+	 */
+
+	if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) {
+		printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d\n",
+			musb->config->gpio_vrsel);
+		return -ENODEV;
+	}
+	gpio_direction_output(musb->config->gpio_vrsel, 0);
+
+	usb_nop_xceiv_register();
+	musb->xceiv = otg_get_transceiver();
+	if (!musb->xceiv) {
+		gpio_free(musb->config->gpio_vrsel);
+		return -ENODEV;
+	}
+
+	musb_platform_reg_init(musb);
 
 	if (is_host_enabled(musb)) {
 		musb->board_set_vbus = bfin_set_vbus;
@@ -394,6 +401,27 @@ int __init musb_platform_init(struct musb *musb, void *board_data)
 	return 0;
 }
 
+#ifdef CONFIG_PM
+void musb_platform_save_context(struct musb *musb,
+			struct musb_context_registers *musb_context)
+{
+	if (is_host_active(musb))
+		/*
+		 * During hibernate gpio_vrsel will change from high to low
+		 * low which will generate wakeup event resume the system
+		 * immediately.  Set it to 0 before hibernate to avoid this
+		 * wakeup event.
+		 */
+		gpio_set_value(musb->config->gpio_vrsel, 0);
+}
+
+void musb_platform_restore_context(struct musb *musb,
+			struct musb_context_registers *musb_context)
+{
+	musb_platform_reg_init(musb);
+}
+#endif
+
 int musb_platform_exit(struct musb *musb)
 {
 	gpio_free(musb->config->gpio_vrsel);

drivers/usb/musb/musb_core.c

@@ -552,7 +552,8 @@ static irqreturn_t musb_stage0_irq(struct musb *musb, u8 int_usb,
 	if (int_usb & MUSB_INTR_SESSREQ) {
 		void __iomem *mbase = musb->mregs;
 
-		if (devctl & MUSB_DEVCTL_BDEVICE) {
+		if ((devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS
+				&& (devctl & MUSB_DEVCTL_BDEVICE)) {
 			DBG(3, "SessReq while on B state\n");
 			return IRQ_HANDLED;
 		}
@@ -1052,6 +1053,11 @@ static void musb_shutdown(struct platform_device *pdev)
 		clk_put(musb->clock);
 	spin_unlock_irqrestore(&musb->lock, flags);
 
+	if (!is_otg_enabled(musb) && is_host_enabled(musb))
+		usb_remove_hcd(musb_to_hcd(musb));
+	musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
+	musb_platform_exit(musb);
+
 	/* FIXME power down */
 }
 
@@ -2244,13 +2250,6 @@ static int __exit musb_remove(struct platform_device *pdev)
 	 */
 	musb_exit_debugfs(musb);
 	musb_shutdown(pdev);
-#ifdef CONFIG_USB_MUSB_HDRC_HCD
-	if (musb->board_mode == MUSB_HOST)
-		usb_remove_hcd(musb_to_hcd(musb));
-#endif
-	musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
-	musb_platform_exit(musb);
-	musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
 
 	musb_free(musb);
 	iounmap(ctrl_base);
@@ -2411,9 +2410,6 @@ static int musb_suspend(struct device *dev)
 	unsigned long	flags;
 	struct musb	*musb = dev_to_musb(&pdev->dev);
 
-	if (!musb->clock)
-		return 0;
-
 	spin_lock_irqsave(&musb->lock, flags);
 
 	if (is_peripheral_active(musb)) {
@@ -2428,10 +2424,12 @@ static int musb_suspend(struct device *dev)
 
 	musb_save_context(musb);
 
-	if (musb->set_clock)
-		musb->set_clock(musb->clock, 0);
-	else
-		clk_disable(musb->clock);
+	if (musb->clock) {
+		if (musb->set_clock)
+			musb->set_clock(musb->clock, 0);
+		else
+			clk_disable(musb->clock);
+	}
 	spin_unlock_irqrestore(&musb->lock, flags);
 	return 0;
 }
@@ -2441,13 +2439,12 @@ static int musb_resume_noirq(struct device *dev)
 	struct platform_device *pdev = to_platform_device(dev);
 	struct musb	*musb = dev_to_musb(&pdev->dev);
 
-	if (!musb->clock)
-		return 0;
-
-	if (musb->set_clock)
-		musb->set_clock(musb->clock, 1);
-	else
-		clk_enable(musb->clock);
+	if (musb->clock) {
+		if (musb->set_clock)
+			musb->set_clock(musb->clock, 1);
+		else
+			clk_enable(musb->clock);
+	}
 
 	musb_restore_context(musb);
 

drivers/usb/musb/musb_core.h

@@ -487,7 +487,7 @@ struct musb_context_registers {
 };
 
 #if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3) || \
-    defined(CONFIG_ARCH_OMAP4)
+    defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_BLACKFIN)
 extern void musb_platform_save_context(struct musb *musb,
 		struct musb_context_registers *musb_context);
 extern void musb_platform_restore_context(struct musb *musb,

drivers/usb/musb/musb_gadget.c

@@ -644,10 +644,8 @@ static void rxstate(struct musb *musb, struct musb_request *req)
 	 */
 
 				csr |= MUSB_RXCSR_DMAENAB;
-				if (!musb_ep->hb_mult &&
-					musb_ep->hw_ep->rx_double_buffered)
-					csr |= MUSB_RXCSR_AUTOCLEAR;
 #ifdef USE_MODE1
+				csr |= MUSB_RXCSR_AUTOCLEAR;
 				/* csr |= MUSB_RXCSR_DMAMODE; */
 
 				/* this special sequence (enabling and then
@@ -656,6 +654,10 @@ static void rxstate(struct musb *musb, struct musb_request *req)
 				 */
 				musb_writew(epio, MUSB_RXCSR,
 					csr | MUSB_RXCSR_DMAMODE);
+#else
+				if (!musb_ep->hb_mult &&
+					musb_ep->hw_ep->rx_double_buffered)
+					csr |= MUSB_RXCSR_AUTOCLEAR;
 #endif
 				musb_writew(epio, MUSB_RXCSR, csr);
 
@@ -807,7 +809,7 @@ void musb_g_rx(struct musb *musb, u8 epnum)
 
 #if defined(CONFIG_USB_INVENTRA_DMA) || defined(CONFIG_USB_TUSB_OMAP_DMA)
 		/* Autoclear doesn't clear RxPktRdy for short packets */
-		if ((dma->desired_mode == 0)
+		if ((dma->desired_mode == 0 && !hw_ep->rx_double_buffered)
 				|| (dma->actual_len
 					& (musb_ep->packet_sz - 1))) {
 			/* ack the read! */
@@ -818,8 +820,16 @@ void musb_g_rx(struct musb *musb, u8 epnum)
 		/* incomplete, and not short? wait for next IN packet */
 		if ((request->actual < request->length)
 				&& (musb_ep->dma->actual_len
-					== musb_ep->packet_sz))
+					== musb_ep->packet_sz)) {
+			/* In double buffer case, continue to unload fifo if
+ 			 * there is Rx packet in FIFO.
+ 			 **/
+			csr = musb_readw(epio, MUSB_RXCSR);
+			if ((csr & MUSB_RXCSR_RXPKTRDY) &&
+				hw_ep->rx_double_buffered)
+				goto exit;
 			return;
+		}
 #endif
 		musb_g_giveback(musb_ep, request, 0);
 
@@ -827,7 +837,7 @@ void musb_g_rx(struct musb *musb, u8 epnum)
 		if (!request)
 			return;
 	}
-
+exit:
 	/* Analyze request */
 	rxstate(musb, to_musb_request(request));
 }
@@ -916,13 +926,9 @@ static int musb_gadget_enable(struct usb_ep *ep,
 		 * likewise high bandwidth periodic tx
 		 */
 		/* Set TXMAXP with the FIFO size of the endpoint
-		 * to disable double buffering mode. Currently, It seems that double
-		 * buffering has problem if musb RTL revision number < 2.0.
+		 * to disable double buffering mode.
 		 */
-		if (musb->hwvers < MUSB_HWVERS_2000)
-			musb_writew(regs, MUSB_TXMAXP, hw_ep->max_packet_sz_tx);
-		else
-			musb_writew(regs, MUSB_TXMAXP, musb_ep->packet_sz | (musb_ep->hb_mult << 11));
+		musb_writew(regs, MUSB_TXMAXP, musb_ep->packet_sz | (musb_ep->hb_mult << 11));
 
 		csr = MUSB_TXCSR_MODE | MUSB_TXCSR_CLRDATATOG;
 		if (musb_readw(regs, MUSB_TXCSR)
@@ -958,10 +964,7 @@ static int musb_gadget_enable(struct usb_ep *ep,
 		/* Set RXMAXP with the FIFO size of the endpoint
 		 * to disable double buffering mode.
 		 */
-		if (musb->hwvers < MUSB_HWVERS_2000)
-			musb_writew(regs, MUSB_RXMAXP, hw_ep->max_packet_sz_rx);
-		else
-			musb_writew(regs, MUSB_RXMAXP, musb_ep->packet_sz | (musb_ep->hb_mult << 11));
+		musb_writew(regs, MUSB_RXMAXP, musb_ep->packet_sz | (musb_ep->hb_mult << 11));
 
 		/* force shared fifo to OUT-only mode */
 		if (hw_ep->is_shared_fifo) {
@@ -1166,8 +1169,6 @@ static int musb_gadget_queue(struct usb_ep *ep, struct usb_request *req,
 						: DMA_FROM_DEVICE);
 			request->mapped = 0;
 		}
-	} else if (!req->buf) {
-		return -ENODATA;
 	} else
 		request->mapped = 0;
 
@@ -1695,8 +1696,10 @@ int __init musb_gadget_setup(struct musb *musb)
 	musb_platform_try_idle(musb, 0);
 
 	status = device_register(&musb->g.dev);
-	if (status != 0)
+	if (status != 0) {
+		put_device(&musb->g.dev);
 		the_gadget = NULL;
+	}
 	return status;
 }
 

drivers/usb/musb/musb_regs.h

@@ -633,8 +633,9 @@ static inline u8  musb_read_txhubaddr(void __iomem *mbase, u8 epnum)
 	return 0;
 }
 
-static inline void  musb_read_txhubport(void __iomem *mbase, u8 epnum)
+static inline u8 musb_read_txhubport(void __iomem *mbase, u8 epnum)
 {
+	return 0;
 }
 
 #endif /* CONFIG_BLACKFIN */

drivers/usb/musb/musbhsdma.c

@@ -158,6 +158,8 @@ static int dma_channel_program(struct dma_channel *channel,
 				dma_addr_t dma_addr, u32 len)
 {
 	struct musb_dma_channel *musb_channel = channel->private_data;
+	struct musb_dma_controller *controller = musb_channel->controller;
+	struct musb *musb = controller->private_data;
 
 	DBG(2, "ep%d-%s pkt_sz %d, dma_addr 0x%x length %d, mode %d\n",
 		musb_channel->epnum,
@@ -167,6 +169,18 @@ static int dma_channel_program(struct dma_channel *channel,
 	BUG_ON(channel->status == MUSB_DMA_STATUS_UNKNOWN ||
 		channel->status == MUSB_DMA_STATUS_BUSY);
 
+	/*
+	 * The DMA engine in RTL1.8 and above cannot handle
+	 * DMA addresses that are not aligned to a 4 byte boundary.
+	 * It ends up masking the last two bits of the address
+	 * programmed in DMA_ADDR.
+	 *
+	 * Fail such DMA transfers, so that the backup PIO mode
+	 * can carry out the transfer
+	 */
+	if ((musb->hwvers >= MUSB_HWVERS_1800) && (dma_addr % 4))
+		return false;
+
 	channel->actual_len = 0;
 	musb_channel->start_addr = dma_addr;
 	musb_channel->len = len;

include/linux/usb/musb.h

@@ -89,6 +89,8 @@ struct musb_hdrc_config {
 	/* A GPIO controlling VRSEL in Blackfin */
 	unsigned int	gpio_vrsel;
 	unsigned int	gpio_vrsel_active;
+	/* musb CLKIN in Blackfin in MHZ */
+	unsigned char   clkin;
 #endif
 
 };