Merge branch 'for-davem' of git://gitorious.org/linux-can/linux-can-next

Marc Kleine-Budde says:

====================
this is a pull-request for net-next/master. There is are 9 patches by
Fabio Baltieri and Kurt Van Dijck which add LED infrastructure and
support for CAN devices. Bernd Krumboeck adds a driver for the USB CAN
adapter from 8 devices. Oliver Hartkopp improves the CAN gateway
functionality. There are 4 patches by me, which clean up the CAN's
Kconfig.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/can/Kconfig

 menu "CAN Device Drivers"
-	depends on CAN
 
 config CAN_VCAN
 	tristate "Virtual Local CAN Interface (vcan)"
-	depends on CAN
 	---help---
 	  Similar to the network loopback devices, vcan offers a
 	  virtual local CAN interface.
@@ -13,7 +11,6 @@ config CAN_VCAN
 
 config CAN_SLCAN
 	tristate "Serial / USB serial CAN Adaptors (slcan)"
-	depends on CAN
 	---help---
 	  CAN driver for several 'low cost' CAN interfaces that are attached
 	  via serial lines or via USB-to-serial adapters using the LAWICEL
@@ -33,16 +30,16 @@ config CAN_SLCAN
 
 config CAN_DEV
 	tristate "Platform CAN drivers with Netlink support"
-	depends on CAN
 	default y
 	---help---
 	  Enables the common framework for platform CAN drivers with Netlink
 	  support. This is the standard library for CAN drivers.
 	  If unsure, say Y.
 
+if CAN_DEV
+
 config CAN_CALC_BITTIMING
 	bool "CAN bit-timing calculation"
-	depends on CAN_DEV
 	default y
 	---help---
 	  If enabled, CAN bit-timing parameters will be calculated for the
@@ -54,15 +51,26 @@ config CAN_CALC_BITTIMING
 	  arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw".
 	  If unsure, say Y.
 
+config CAN_LEDS
+	bool "Enable LED triggers for Netlink based drivers"
+	depends on LEDS_CLASS
+	select LEDS_TRIGGERS
+	---help---
+	  This option adds two LED triggers for packet receive and transmit
+	  events on each supported CAN device.
+
+	  Say Y here if you are working on a system with led-class supported
+	  LEDs and you want to use them as canbus activity indicators.
+
 config CAN_AT91
 	tristate "Atmel AT91 onchip CAN controller"
-	depends on CAN_DEV && (ARCH_AT91SAM9263 || ARCH_AT91SAM9X5)
+	depends on ARCH_AT91SAM9263 || ARCH_AT91SAM9X5
 	---help---
 	  This is a driver for the SoC CAN controller in Atmel's AT91SAM9263
 	  and AT91SAM9X5 processors.
 
 config CAN_TI_HECC
-	depends on CAN_DEV && ARCH_OMAP3
+	depends on ARCH_OMAP3
 	tristate "TI High End CAN Controller"
 	---help---
 	  Driver for TI HECC (High End CAN Controller) module found on many
@@ -70,12 +78,12 @@ config CAN_TI_HECC
 
 config CAN_MCP251X
 	tristate "Microchip MCP251x SPI CAN controllers"
-	depends on CAN_DEV && SPI && HAS_DMA
+	depends on SPI && HAS_DMA
 	---help---
 	  Driver for the Microchip MCP251x SPI CAN controllers.
 
 config CAN_BFIN
-	depends on CAN_DEV && (BF534 || BF536 || BF537 || BF538 || BF539 || BF54x)
+	depends on BF534 || BF536 || BF537 || BF538 || BF539 || BF54x
 	tristate "Analog Devices Blackfin on-chip CAN"
 	---help---
 	  Driver for the Analog Devices Blackfin on-chip CAN controllers
@@ -85,7 +93,7 @@ config CAN_BFIN
 
 config CAN_JANZ_ICAN3
 	tristate "Janz VMOD-ICAN3 Intelligent CAN controller"
-	depends on CAN_DEV && MFD_JANZ_CMODIO
+	depends on MFD_JANZ_CMODIO
 	---help---
 	  Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which
 	  connects to a MODULbus carrier board.
@@ -98,13 +106,13 @@ config HAVE_CAN_FLEXCAN
 
 config CAN_FLEXCAN
 	tristate "Support for Freescale FLEXCAN based chips"
-	depends on CAN_DEV && HAVE_CAN_FLEXCAN
+	depends on HAVE_CAN_FLEXCAN
 	---help---
 	  Say Y here if you want to support for Freescale FlexCAN.
 
 config PCH_CAN
 	tristate "Intel EG20T PCH CAN controller"
-	depends on CAN_DEV && PCI
+	depends on PCI
 	---help---
 	  This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which
 	  is an IOH for x86 embedded processor (Intel Atom E6xx series).
@@ -112,7 +120,7 @@ config PCH_CAN
 
 config CAN_GRCAN
 	tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices"
-	depends on CAN_DEV && OF
+	depends on OF
 	---help---
 	  Say Y here if you want to use Aeroflex Gaisler GRCAN or GRHCAN.
 	  Note that the driver supports little endian, even though little
@@ -131,9 +139,10 @@ source "drivers/net/can/usb/Kconfig"
 
 source "drivers/net/can/softing/Kconfig"
 
+endif
+
 config CAN_DEBUG_DEVICES
 	bool "CAN devices debugging messages"
-	depends on CAN
 	---help---
 	  Say Y here if you want the CAN device drivers to produce a bunch of
 	  debug messages to the system log.  Select this if you are having

drivers/net/can/Makefile

@@ -8,6 +8,8 @@ obj-$(CONFIG_CAN_SLCAN)		+= slcan.o
 obj-$(CONFIG_CAN_DEV)		+= can-dev.o
 can-dev-y			:= dev.o
 
+can-dev-$(CONFIG_CAN_LEDS)	+= led.o
+
 obj-y				+= usb/
 obj-y				+= softing/
 

drivers/net/can/at91_can.c

@@ -37,6 +37,7 @@
 
 #include <linux/can/dev.h>
 #include <linux/can/error.h>
+#include <linux/can/led.h>
 
 #define AT91_MB_MASK(i)		((1 << (i)) - 1)
 
@@ -641,6 +642,8 @@ static void at91_read_msg(struct net_device *dev, unsigned int mb)
 
 	stats->rx_packets++;
 	stats->rx_bytes += cf->can_dlc;
+
+	can_led_event(dev, CAN_LED_EVENT_RX);
 }
 
 /**
@@ -875,6 +878,7 @@ static void at91_irq_tx(struct net_device *dev, u32 reg_sr)
 			/* _NOTE_: subtract AT91_MB_TX_FIRST offset from mb! */
 			can_get_echo_skb(dev, mb - get_mb_tx_first(priv));
 			dev->stats.tx_packets++;
+			can_led_event(dev, CAN_LED_EVENT_TX);
 		}
 	}
 
@@ -1128,6 +1132,8 @@ static int at91_open(struct net_device *dev)
 		goto out_close;
 	}
 
+	can_led_event(dev, CAN_LED_EVENT_OPEN);
+
 	/* start chip and queuing */
 	at91_chip_start(dev);
 	napi_enable(&priv->napi);
@@ -1159,6 +1165,8 @@ static int at91_close(struct net_device *dev)
 
 	close_candev(dev);
 
+	can_led_event(dev, CAN_LED_EVENT_STOP);
+
 	return 0;
 }
 
@@ -1321,6 +1329,8 @@ static int at91_can_probe(struct platform_device *pdev)
 		goto exit_free;
 	}
 
+	devm_can_led_init(dev);
+
 	dev_info(&pdev->dev, "device registered (reg_base=%p, irq=%d)\n",
 		 priv->reg_base, dev->irq);
 

drivers/net/can/c_can/Kconfig

 menuconfig CAN_C_CAN
 	tristate "Bosch C_CAN/D_CAN devices"
-	depends on CAN_DEV && HAS_IOMEM
+	depends on HAS_IOMEM
 
 if CAN_C_CAN
 

drivers/net/can/c_can/c_can.c

@@ -39,6 +39,7 @@
 #include <linux/can.h>
 #include <linux/can/dev.h>
 #include <linux/can/error.h>
+#include <linux/can/led.h>
 
 #include "c_can.h"
 
@@ -477,6 +478,8 @@ static int c_can_read_msg_object(struct net_device *dev, int iface, int ctrl)
 	stats->rx_packets++;
 	stats->rx_bytes += frame->can_dlc;
 
+	can_led_event(dev, CAN_LED_EVENT_RX);
+
 	return 0;
 }
 
@@ -751,6 +754,7 @@ static void c_can_do_tx(struct net_device *dev)
 					C_CAN_IFACE(MSGCTRL_REG, 0))
 					& IF_MCONT_DLC_MASK;
 			stats->tx_packets++;
+			can_led_event(dev, CAN_LED_EVENT_TX);
 			c_can_inval_msg_object(dev, 0, msg_obj_no);
 		} else {
 			break;
@@ -1115,6 +1119,8 @@ static int c_can_open(struct net_device *dev)
 
 	napi_enable(&priv->napi);
 
+	can_led_event(dev, CAN_LED_EVENT_OPEN);
+
 	/* start the c_can controller */
 	c_can_start(dev);
 
@@ -1143,6 +1149,8 @@ static int c_can_close(struct net_device *dev)
 	c_can_reset_ram(priv, false);
 	c_can_pm_runtime_put_sync(priv);
 
+	can_led_event(dev, CAN_LED_EVENT_STOP);
+
 	return 0;
 }
 
@@ -1268,6 +1276,8 @@ int register_c_can_dev(struct net_device *dev)
 	err = register_candev(dev);
 	if (err)
 		c_can_pm_runtime_disable(priv);
+	else
+		devm_can_led_init(dev);
 
 	return err;
 }

drivers/net/can/cc770/Kconfig

 menuconfig CAN_CC770
 	tristate "Bosch CC770 and Intel AN82527 devices"
-	depends on CAN_DEV && HAS_IOMEM
+	depends on HAS_IOMEM
 
 if CAN_CC770
 

drivers/net/can/dev.c

@@ -24,7 +24,9 @@
 #include <linux/if_arp.h>
 #include <linux/can.h>
 #include <linux/can/dev.h>
+#include <linux/can/skb.h>
 #include <linux/can/netlink.h>
+#include <linux/can/led.h>
 #include <net/rtnetlink.h>
 
 #define MOD_DESC "CAN device driver interface"
@@ -501,13 +503,18 @@ struct sk_buff *alloc_can_skb(struct net_device *dev, struct can_frame **cf)
 {
 	struct sk_buff *skb;
 
-	skb = netdev_alloc_skb(dev, sizeof(struct can_frame));
+	skb = netdev_alloc_skb(dev, sizeof(struct can_skb_priv) +
+			       sizeof(struct can_frame));
 	if (unlikely(!skb))
 		return NULL;
 
 	skb->protocol = htons(ETH_P_CAN);
 	skb->pkt_type = PACKET_BROADCAST;
 	skb->ip_summed = CHECKSUM_UNNECESSARY;
+
+	skb_reserve(skb, sizeof(struct can_skb_priv));
+	((struct can_skb_priv *)(skb->head))->ifindex = dev->ifindex;
+
 	*cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame));
 	memset(*cf, 0, sizeof(struct can_frame));
 
@@ -794,10 +801,25 @@ void unregister_candev(struct net_device *dev)
 }
 EXPORT_SYMBOL_GPL(unregister_candev);
 
+/*
+ * Test if a network device is a candev based device
+ * and return the can_priv* if so.
+ */
+struct can_priv *safe_candev_priv(struct net_device *dev)
+{
+	if ((dev->type != ARPHRD_CAN) || (dev->rtnl_link_ops != &can_link_ops))
+		return NULL;
+
+	return netdev_priv(dev);
+}
+EXPORT_SYMBOL_GPL(safe_candev_priv);
+
 static __init int can_dev_init(void)
 {
 	int err;
 
+	can_led_notifier_init();
+
 	err = rtnl_link_register(&can_link_ops);
 	if (!err)
 		printk(KERN_INFO MOD_DESC "\n");
@@ -809,6 +831,8 @@ module_init(can_dev_init);
 static __exit void can_dev_exit(void)
 {
 	rtnl_link_unregister(&can_link_ops);
+
+	can_led_notifier_exit();
 }
 module_exit(can_dev_exit);
 

drivers/net/can/flexcan.c

@@ -23,6 +23,7 @@
 #include <linux/can.h>
 #include <linux/can/dev.h>
 #include <linux/can/error.h>
+#include <linux/can/led.h>
 #include <linux/can/platform/flexcan.h>
 #include <linux/clk.h>
 #include <linux/delay.h>
@@ -564,6 +565,8 @@ static int flexcan_read_frame(struct net_device *dev)
 	stats->rx_packets++;
 	stats->rx_bytes += cf->can_dlc;
 
+	can_led_event(dev, CAN_LED_EVENT_RX);
+
 	return 1;
 }
 
@@ -652,6 +655,7 @@ static irqreturn_t flexcan_irq(int irq, void *dev_id)
 	if (reg_iflag1 & (1 << FLEXCAN_TX_BUF_ID)) {
 		stats->tx_bytes += can_get_echo_skb(dev, 0);
 		stats->tx_packets++;
+		can_led_event(dev, CAN_LED_EVENT_TX);
 		flexcan_write((1 << FLEXCAN_TX_BUF_ID), &regs->iflag1);
 		netif_wake_queue(dev);
 	}
@@ -865,6 +869,9 @@ static int flexcan_open(struct net_device *dev)
 	err = flexcan_chip_start(dev);
 	if (err)
 		goto out_close;
+
+	can_led_event(dev, CAN_LED_EVENT_OPEN);
+
 	napi_enable(&priv->napi);
 	netif_start_queue(dev);
 
@@ -893,6 +900,8 @@ static int flexcan_close(struct net_device *dev)
 
 	close_candev(dev);
 
+	can_led_event(dev, CAN_LED_EVENT_STOP);
+
 	return 0;
 }
 
@@ -1092,6 +1101,8 @@ static int flexcan_probe(struct platform_device *pdev)
 		goto failed_register;
 	}
 
+	devm_can_led_init(dev);
+
 	dev_info(&pdev->dev, "device registered (reg_base=%p, irq=%d)\n",
 		 priv->base, dev->irq);
 

drivers/net/can/led.c

+/*
+ * Copyright 2012, Fabio Baltieri <fabio.baltieri@gmail.com>
+ * Copyright 2012, Kurt Van Dijck <kurt.van.dijck@eia.be>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/netdevice.h>
+#include <linux/can/dev.h>
+
+#include <linux/can/led.h>
+
+static unsigned long led_delay = 50;
+module_param(led_delay, ulong, 0644);
+MODULE_PARM_DESC(led_delay,
+		"blink delay time for activity leds (msecs, default: 50).");
+
+/* Trigger a LED event in response to a CAN device event */
+void can_led_event(struct net_device *netdev, enum can_led_event event)
+{
+	struct can_priv *priv = netdev_priv(netdev);
+
+	switch (event) {
+	case CAN_LED_EVENT_OPEN:
+		led_trigger_event(priv->tx_led_trig, LED_FULL);
+		led_trigger_event(priv->rx_led_trig, LED_FULL);
+		break;
+	case CAN_LED_EVENT_STOP:
+		led_trigger_event(priv->tx_led_trig, LED_OFF);
+		led_trigger_event(priv->rx_led_trig, LED_OFF);
+		break;
+	case CAN_LED_EVENT_TX:
+		if (led_delay)
+			led_trigger_blink_oneshot(priv->tx_led_trig,
+						  &led_delay, &led_delay, 1);
+		break;
+	case CAN_LED_EVENT_RX:
+		if (led_delay)
+			led_trigger_blink_oneshot(priv->rx_led_trig,
+						  &led_delay, &led_delay, 1);
+		break;
+	}
+}
+EXPORT_SYMBOL_GPL(can_led_event);
+
+static void can_led_release(struct device *gendev, void *res)
+{
+	struct can_priv *priv = netdev_priv(to_net_dev(gendev));
+
+	led_trigger_unregister_simple(priv->tx_led_trig);
+	led_trigger_unregister_simple(priv->rx_led_trig);
+}
+
+/* Register CAN LED triggers for a CAN device
+ *
+ * This is normally called from a driver's probe function
+ */
+void devm_can_led_init(struct net_device *netdev)
+{
+	struct can_priv *priv = netdev_priv(netdev);
+	void *res;
+
+	res = devres_alloc(can_led_release, 0, GFP_KERNEL);
+	if (!res) {
+		netdev_err(netdev, "cannot register LED triggers\n");
+		return;
+	}
+
+	snprintf(priv->tx_led_trig_name, sizeof(priv->tx_led_trig_name),
+		 "%s-tx", netdev->name);
+	snprintf(priv->rx_led_trig_name, sizeof(priv->rx_led_trig_name),
+		 "%s-rx", netdev->name);
+
+	led_trigger_register_simple(priv->tx_led_trig_name,
+				    &priv->tx_led_trig);
+	led_trigger_register_simple(priv->rx_led_trig_name,
+				    &priv->rx_led_trig);
+
+	devres_add(&netdev->dev, res);
+}
+EXPORT_SYMBOL_GPL(devm_can_led_init);
+
+/* NETDEV rename notifier to rename the associated led triggers too */
+static int can_led_notifier(struct notifier_block *nb, unsigned long msg,
+			void *data)
+{
+	struct net_device *netdev = data;
+	struct can_priv *priv = safe_candev_priv(netdev);
+	char name[CAN_LED_NAME_SZ];
+
+	if (!priv)
+		return NOTIFY_DONE;
+
+	if (msg == NETDEV_CHANGENAME) {
+		snprintf(name, sizeof(name), "%s-tx", netdev->name);
+		led_trigger_rename_static(name, priv->tx_led_trig);
+
+		snprintf(name, sizeof(name), "%s-rx", netdev->name);
+		led_trigger_rename_static(name, priv->rx_led_trig);
+	}
+
+	return NOTIFY_DONE;
+}
+
+/* notifier block for netdevice event */
+static struct notifier_block can_netdev_notifier __read_mostly = {
+	.notifier_call = can_led_notifier,
+};
+
+int __init can_led_notifier_init(void)
+{
+	return register_netdevice_notifier(&can_netdev_notifier);
+}
+
+void __exit can_led_notifier_exit(void)
+{
+	unregister_netdevice_notifier(&can_netdev_notifier);
+}

drivers/net/can/mcp251x.c

@@ -60,6 +60,7 @@
 
 #include <linux/can/core.h>
 #include <linux/can/dev.h>
+#include <linux/can/led.h>
 #include <linux/can/platform/mcp251x.h>
 #include <linux/completion.h>
 #include <linux/delay.h>
@@ -494,6 +495,9 @@ static void mcp251x_hw_rx(struct spi_device *spi, int buf_idx)
 
 	priv->net->stats.rx_packets++;
 	priv->net->stats.rx_bytes += frame->can_dlc;
+
+	can_led_event(priv->net, CAN_LED_EVENT_RX);
+
 	netif_rx_ni(skb);
 }
 
@@ -707,6 +711,8 @@ static int mcp251x_stop(struct net_device *net)
 
 	mutex_unlock(&priv->mcp_lock);
 
+	can_led_event(net, CAN_LED_EVENT_STOP);
+
 	return 0;
 }
 
@@ -905,6 +911,7 @@ static irqreturn_t mcp251x_can_ist(int irq, void *dev_id)
 		if (intf & CANINTF_TX) {
 			net->stats.tx_packets++;
 			net->stats.tx_bytes += priv->tx_len - 1;
+			can_led_event(net, CAN_LED_EVENT_TX);
 			if (priv->tx_len) {
 				can_get_echo_skb(net, 0);
 				priv->tx_len = 0;
@@ -968,6 +975,9 @@ static int mcp251x_open(struct net_device *net)
 		mcp251x_open_clean(net);
 		goto open_unlock;
 	}
+
+	can_led_event(net, CAN_LED_EVENT_OPEN);
+
 	netif_wake_queue(net);
 
 open_unlock:
@@ -1077,10 +1087,15 @@ static int mcp251x_can_probe(struct spi_device *spi)
 		pdata->transceiver_enable(0);
 
 	ret = register_candev(net);
-	if (!ret) {
-		dev_info(&spi->dev, "probed\n");
-		return ret;
-	}
+	if (ret)
+		goto error_probe;
+
+	devm_can_led_init(net);
+
+	dev_info(&spi->dev, "probed\n");
+
+	return ret;
+
 error_probe:
 	if (!mcp251x_enable_dma)
 		kfree(priv->spi_rx_buf);

drivers/net/can/mscan/Kconfig

 config CAN_MSCAN
-	depends on CAN_DEV && (PPC || M68K)
+	depends on PPC || M68K
 	tristate "Support for Freescale MSCAN based chips"
 	---help---
 	  The Motorola Scalable Controller Area Network (MSCAN) definition

drivers/net/can/sja1000/Kconfig

 menuconfig CAN_SJA1000
 	tristate "Philips/NXP SJA1000 devices"
-	depends on CAN_DEV && HAS_IOMEM
+	depends on HAS_IOMEM
 
 if CAN_SJA1000
 
@@ -99,11 +99,11 @@ config CAN_TSCAN1
 	tristate "TS-CAN1 PC104 boards"
 	depends on ISA
 	help
-	This driver is for Technologic Systems' TSCAN-1 PC104 boards.
-	http://www.embeddedarm.com/products/board-detail.php?product=TS-CAN1
-	The driver supports multiple boards and automatically configures them:
-	PLD IO base addresses are read from jumpers JP1 and JP2,
-	IRQ numbers are read from jumpers JP4 and JP5,
-	SJA1000 IO base addresses are chosen heuristically (first that works).
+	  This driver is for Technologic Systems' TSCAN-1 PC104 boards.
+	  http://www.embeddedarm.com/products/board-detail.php?product=TS-CAN1
+	  The driver supports multiple boards and automatically configures them:
+	  PLD IO base addresses are read from jumpers JP1 and JP2,
+	  IRQ numbers are read from jumpers JP4 and JP5,
+	  SJA1000 IO base addresses are chosen heuristically (first that works).
 
 endif

drivers/net/can/sja1000/sja1000.c

@@ -60,6 +60,7 @@
 
 #include <linux/can/dev.h>
 #include <linux/can/error.h>
+#include <linux/can/led.h>
 
 #include "sja1000.h"
 
@@ -368,6 +369,8 @@ static void sja1000_rx(struct net_device *dev)
 
 	stats->rx_packets++;
 	stats->rx_bytes += cf->can_dlc;
+
+	can_led_event(dev, CAN_LED_EVENT_RX);
 }
 
 static int sja1000_err(struct net_device *dev, uint8_t isrc, uint8_t status)
@@ -521,6 +524,7 @@ irqreturn_t sja1000_interrupt(int irq, void *dev_id)
 				can_get_echo_skb(dev, 0);
 			}
 			netif_wake_queue(dev);
+			can_led_event(dev, CAN_LED_EVENT_TX);
 		}
 		if (isrc & IRQ_RI) {
 			/* receive interrupt */
@@ -575,6 +579,8 @@ static int sja1000_open(struct net_device *dev)
 	/* init and start chi */
 	sja1000_start(dev);
 
+	can_led_event(dev, CAN_LED_EVENT_OPEN);
+
 	netif_start_queue(dev);
 
 	return 0;
@@ -592,6 +598,8 @@ static int sja1000_close(struct net_device *dev)
 
 	close_candev(dev);
 
+	can_led_event(dev, CAN_LED_EVENT_STOP);
+
 	return 0;
 }
 
@@ -639,6 +647,8 @@ static const struct net_device_ops sja1000_netdev_ops = {
 
 int register_sja1000dev(struct net_device *dev)
 {
+	int ret;
+
 	if (!sja1000_probe_chip(dev))
 		return -ENODEV;
 
@@ -648,7 +658,12 @@ int register_sja1000dev(struct net_device *dev)
 	set_reset_mode(dev);
 	chipset_init(dev);
 
-	return register_candev(dev);
+	ret =  register_candev(dev);
+
+	if (!ret)
+		devm_can_led_init(dev);
+
+	return ret;
 }
 EXPORT_SYMBOL_GPL(register_sja1000dev);
 

drivers/net/can/slcan.c

@@ -55,6 +55,7 @@
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/can.h>
+#include <linux/can/skb.h>
 
 static __initconst const char banner[] =
 	KERN_INFO "slcan: serial line CAN interface driver\n";
@@ -184,7 +185,8 @@ static void slc_bump(struct slcan *sl)
 		cf.data[i] |= tmp;
 	}
 
-	skb = dev_alloc_skb(sizeof(struct can_frame));
+	skb = dev_alloc_skb(sizeof(struct can_frame) +
+			    sizeof(struct can_skb_priv));
 	if (!skb)
 		return;
 
@@ -192,6 +194,10 @@ static void slc_bump(struct slcan *sl)
 	skb->protocol = htons(ETH_P_CAN);
 	skb->pkt_type = PACKET_BROADCAST;
 	skb->ip_summed = CHECKSUM_UNNECESSARY;
+
+	skb_reserve(skb, sizeof(struct can_skb_priv));
+	((struct can_skb_priv *)(skb->head))->ifindex = sl->dev->ifindex;
+
 	memcpy(skb_put(skb, sizeof(struct can_frame)),
 	       &cf, sizeof(struct can_frame));
 	netif_rx_ni(skb);

drivers/net/can/softing/Kconfig

 config CAN_SOFTING
 	tristate "Softing Gmbh CAN generic support"
-	depends on CAN_DEV && HAS_IOMEM
+	depends on HAS_IOMEM
 	---help---
 	  Support for CAN cards from Softing Gmbh & some cards
 	  from Vector Gmbh.

drivers/net/can/ti_hecc.c

@@ -50,6 +50,7 @@
 
 #include <linux/can/dev.h>
 #include <linux/can/error.h>
+#include <linux/can/led.h>
 #include <linux/can/platform/ti_hecc.h>
 
 #define DRV_NAME "ti_hecc"
@@ -593,6 +594,7 @@ static int ti_hecc_rx_pkt(struct ti_hecc_priv *priv, int mbxno)
 	spin_unlock_irqrestore(&priv->mbx_lock, flags);
 
 	stats->rx_bytes += cf->can_dlc;
+	can_led_event(priv->ndev, CAN_LED_EVENT_RX);
 	netif_receive_skb(skb);
 	stats->rx_packets++;
 
@@ -796,6 +798,7 @@ static irqreturn_t ti_hecc_interrupt(int irq, void *dev_id)
 			stats->tx_bytes += hecc_read_mbx(priv, mbxno,
 						HECC_CANMCF) & 0xF;
 			stats->tx_packets++;
+			can_led_event(ndev, CAN_LED_EVENT_TX);
 			can_get_echo_skb(ndev, mbxno);
 			--priv->tx_tail;
 		}
@@ -851,6 +854,8 @@ static int ti_hecc_open(struct net_device *ndev)
 		return err;
 	}
 
+	can_led_event(ndev, CAN_LED_EVENT_OPEN);
+
 	ti_hecc_start(ndev);
 	napi_enable(&priv->napi);
 	netif_start_queue(ndev);
@@ -869,6 +874,8 @@ static int ti_hecc_close(struct net_device *ndev)
 	close_candev(ndev);
 	ti_hecc_transceiver_switch(priv, 0);
 
+	can_led_event(ndev, CAN_LED_EVENT_STOP);
+
 	return 0;
 }
 
@@ -961,6 +968,9 @@ static int ti_hecc_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev, "register_candev() failed\n");
 		goto probe_exit_clk;
 	}
+
+	devm_can_led_init(ndev);
+
 	dev_info(&pdev->dev, "device registered (reg_base=%p, irq=%u)\n",
 		priv->base, (u32) ndev->irq);
 

drivers/net/can/usb/Kconfig

 menu "CAN USB interfaces"
-	depends on USB && CAN_DEV
+	depends on USB
 
 config CAN_EMS_USB
 	tristate "EMS CPC-USB/ARM7 CAN/USB interface"
@@ -48,4 +48,10 @@ config CAN_PEAK_USB
 	  This driver supports the PCAN-USB and PCAN-USB Pro adapters
 	  from PEAK-System Technik (http://www.peak-system.com).
 
+config CAN_8DEV_USB
+	tristate "8 devices USB2CAN interface"
+	---help---
+	  This driver supports the USB2CAN interface
+	  from 8 devices (http://www.8devices.com).
+
 endmenu

drivers/net/can/usb/Makefile

@@ -6,5 +6,6 @@ obj-$(CONFIG_CAN_EMS_USB) += ems_usb.o
 obj-$(CONFIG_CAN_ESD_USB2) += esd_usb2.o
 obj-$(CONFIG_CAN_KVASER_USB) += kvaser_usb.o
 obj-$(CONFIG_CAN_PEAK_USB) += peak_usb/
+obj-$(CONFIG_CAN_8DEV_USB) += usb_8dev.o
 
 ccflags-$(CONFIG_CAN_DEBUG_DEVICES) := -DDEBUG

include/linux/can/dev.h

@@ -16,6 +16,7 @@
 #include <linux/can.h>
 #include <linux/can/netlink.h>
 #include <linux/can/error.h>
+#include <linux/can/led.h>
 
 /*
  * CAN mode
@@ -52,6 +53,13 @@ struct can_priv {
 
 	unsigned int echo_skb_max;
 	struct sk_buff **echo_skb;
+
+#ifdef CONFIG_CAN_LEDS
+	struct led_trigger *tx_led_trig;
+	char tx_led_trig_name[CAN_LED_NAME_SZ];
+	struct led_trigger *rx_led_trig;
+	char rx_led_trig_name[CAN_LED_NAME_SZ];
+#endif
 };
 
 /*
@@ -98,6 +106,9 @@ u8 can_len2dlc(u8 len);
 struct net_device *alloc_candev(int sizeof_priv, unsigned int echo_skb_max);
 void free_candev(struct net_device *dev);
 
+/* a candev safe wrapper around netdev_priv */
+struct can_priv *safe_candev_priv(struct net_device *dev);
+
 int open_candev(struct net_device *dev);
 void close_candev(struct net_device *dev);
 

include/linux/can/led.h

+/*
+ * Copyright 2012, Fabio Baltieri <fabio.baltieri@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef CAN_LED_H
+#define CAN_LED_H
+
+#include <linux/if.h>
+#include <linux/leds.h>
+
+enum can_led_event {
+	CAN_LED_EVENT_OPEN,
+	CAN_LED_EVENT_STOP,
+	CAN_LED_EVENT_TX,
+	CAN_LED_EVENT_RX,
+};
+
+#ifdef CONFIG_CAN_LEDS
+
+/* keep space for interface name + "-tx"/"-rx" suffix and null terminator */
+#define CAN_LED_NAME_SZ (IFNAMSIZ + 4)
+
+void can_led_event(struct net_device *netdev, enum can_led_event event);
+void devm_can_led_init(struct net_device *netdev);
+int __init can_led_notifier_init(void);
+void __exit can_led_notifier_exit(void);
+
+#else
+
+static inline void can_led_event(struct net_device *netdev,
+				 enum can_led_event event)
+{
+}
+static inline void devm_can_led_init(struct net_device *netdev)
+{
+}
+static inline int can_led_notifier_init(void)
+{
+	return 0;
+}
+static inline void can_led_notifier_exit(void)
+{
+}
+
+#endif
+
+#endif

include/linux/can/skb.h

+/*
+ * linux/can/skb.h
+ *
+ * Definitions for the CAN network socket buffer
+ *
+ * Copyright (C) 2012 Oliver Hartkopp <socketcan@hartkopp.net>
+ *
+ */
+
+#ifndef CAN_SKB_H
+#define CAN_SKB_H
+
+#include <linux/types.h>
+#include <linux/can.h>
+
+/*
+ * The struct can_skb_priv is used to transport additional information along
+ * with the stored struct can(fd)_frame that can not be contained in existing
+ * struct sk_buff elements.
+ * N.B. that this information must not be modified in cloned CAN sk_buffs.
+ * To modify the CAN frame content or the struct can_skb_priv content
+ * skb_copy() needs to be used instead of skb_clone().
+ */
+
+/**
+ * struct can_skb_priv - private additional data inside CAN sk_buffs
+ * @ifindex:	ifindex of the first interface the CAN frame appeared on
+ * @cf:		align to the following CAN frame at skb->data
+ */
+struct can_skb_priv {
+	int ifindex;
+	struct can_frame cf[0];
+};
+
+#endif /* CAN_SKB_H */

include/uapi/linux/can/gw.h

@@ -44,6 +44,7 @@ enum {
 	CGW_SRC_IF,	/* ifindex of source network interface */
 	CGW_DST_IF,	/* ifindex of destination network interface */
 	CGW_FILTER,	/* specify struct can_filter on source CAN device */
+	CGW_DELETED,	/* number of deleted CAN frames (see max_hops param) */
 	__CGW_MAX
 };
 
@@ -51,6 +52,7 @@ enum {
 
 #define CGW_FLAGS_CAN_ECHO 0x01
 #define CGW_FLAGS_CAN_SRC_TSTAMP 0x02
+#define CGW_FLAGS_CAN_IIF_TX_OK 0x04
 
 #define CGW_MOD_FUNCS 4 /* AND OR XOR SET */
 

net/can/Kconfig

@@ -16,10 +16,11 @@ menuconfig CAN
 	  If you want CAN support you should say Y here and also to the
 	  specific driver for your controller(s) below.
 
+if CAN
+
 config CAN_RAW
 	tristate "Raw CAN Protocol (raw access with CAN-ID filtering)"
-	depends on CAN
-	default N
+	default y
 	---help---
 	  The raw CAN protocol option offers access to the CAN bus via
 	  the BSD socket API. You probably want to use the raw socket in
@@ -29,8 +30,7 @@ config CAN_RAW
 
 config CAN_BCM
 	tristate "Broadcast Manager CAN Protocol (with content filtering)"
-	depends on CAN
-	default N
+	default y
 	---help---
 	  The Broadcast Manager offers content filtering, timeout monitoring,
 	  sending of RTR frames, and cyclic CAN messages without permanent user
@@ -42,8 +42,7 @@ config CAN_BCM
 
 config CAN_GW
 	tristate "CAN Gateway/Router (with netlink configuration)"
-	depends on CAN
-	default N
+	default y
 	---help---
 	  The CAN Gateway/Router is used to route (and modify) CAN frames.
 	  It is based on the PF_CAN core infrastructure for msg filtering and
@@ -53,3 +52,5 @@ config CAN_GW
 	  by the netlink configuration interface known e.g. from iptables.
 
 source "drivers/net/can/Kconfig"
+
+endif

net/can/bcm.c

@@ -54,6 +54,7 @@
 #include <linux/skbuff.h>
 #include <linux/can.h>
 #include <linux/can/core.h>
+#include <linux/can/skb.h>
 #include <linux/can/bcm.h>
 #include <linux/slab.h>
 #include <net/sock.h>
@@ -256,10 +257,13 @@ static void bcm_can_tx(struct bcm_op *op)
 		return;
 	}
 
-	skb = alloc_skb(CFSIZ, gfp_any());
+	skb = alloc_skb(CFSIZ + sizeof(struct can_skb_priv), gfp_any());
 	if (!skb)
 		goto out;
 
+	skb_reserve(skb, sizeof(struct can_skb_priv));
+	((struct can_skb_priv *)(skb->head))->ifindex = dev->ifindex;
+
 	memcpy(skb_put(skb, CFSIZ), cf, CFSIZ);
 
 	/* send with loopback */
@@ -1199,11 +1203,12 @@ static int bcm_tx_send(struct msghdr *msg, int ifindex, struct sock *sk)
 	if (!ifindex)
 		return -ENODEV;
 
-	skb = alloc_skb(CFSIZ, GFP_KERNEL);
-
+	skb = alloc_skb(CFSIZ + sizeof(struct can_skb_priv), GFP_KERNEL);
 	if (!skb)
 		return -ENOMEM;
 
+	skb_reserve(skb, sizeof(struct can_skb_priv));
+
 	err = memcpy_fromiovec(skb_put(skb, CFSIZ), msg->msg_iov, CFSIZ);
 	if (err < 0) {
 		kfree_skb(skb);
@@ -1216,6 +1221,7 @@ static int bcm_tx_send(struct msghdr *msg, int ifindex, struct sock *sk)
 		return -ENODEV;
 	}
 
+	((struct can_skb_priv *)(skb->head))->ifindex = dev->ifindex;
 	skb->dev = dev;
 	skb->sk  = sk;
 	err = can_send(skb, 1); /* send with loopback */

net/can/gw.c

@@ -42,6 +42,7 @@
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/types.h>
+#include <linux/kernel.h>
 #include <linux/list.h>
 #include <linux/spinlock.h>
 #include <linux/rcupdate.h>
@@ -52,19 +53,31 @@
 #include <linux/skbuff.h>
 #include <linux/can.h>
 #include <linux/can/core.h>
+#include <linux/can/skb.h>
 #include <linux/can/gw.h>
 #include <net/rtnetlink.h>
 #include <net/net_namespace.h>
 #include <net/sock.h>
 
-#define CAN_GW_VERSION "20101209"
-static __initconst const char banner[] =
-	KERN_INFO "can: netlink gateway (rev " CAN_GW_VERSION ")\n";
+#define CAN_GW_VERSION "20130117"
+#define CAN_GW_NAME "can-gw"
 
 MODULE_DESCRIPTION("PF_CAN netlink gateway");
 MODULE_LICENSE("Dual BSD/GPL");
 MODULE_AUTHOR("Oliver Hartkopp <oliver.hartkopp@volkswagen.de>");
-MODULE_ALIAS("can-gw");
+MODULE_ALIAS(CAN_GW_NAME);
+
+#define CGW_MIN_HOPS 1
+#define CGW_MAX_HOPS 6
+#define CGW_DEFAULT_HOPS 1
+
+static unsigned int max_hops __read_mostly = CGW_DEFAULT_HOPS;
+module_param(max_hops, uint, S_IRUGO);
+MODULE_PARM_DESC(max_hops,
+		 "maximum " CAN_GW_NAME " routing hops for CAN frames "
+		 "(valid values: " __stringify(CGW_MIN_HOPS) "-"
+		 __stringify(CGW_MAX_HOPS) " hops, "
+		 "default: " __stringify(CGW_DEFAULT_HOPS) ")");
 
 static HLIST_HEAD(cgw_list);
 static struct notifier_block notifier;
@@ -118,6 +131,7 @@ struct cgw_job {
 	struct rcu_head rcu;
 	u32 handled_frames;
 	u32 dropped_frames;
+	u32 deleted_frames;
 	struct cf_mod mod;
 	union {
 		/* CAN frame data source */
@@ -338,15 +352,40 @@ static void can_can_gw_rcv(struct sk_buff *skb, void *data)
 	struct sk_buff *nskb;
 	int modidx = 0;
 
-	/* do not handle already routed frames - see comment below */
-	if (skb_mac_header_was_set(skb))
+	/*
+	 * Do not handle CAN frames routed more than 'max_hops' times.
+	 * In general we should never catch this delimiter which is intended
+	 * to cover a misconfiguration protection (e.g. circular CAN routes).
+	 *
+	 * The Controller Area Network controllers only accept CAN frames with
+	 * correct CRCs - which are not visible in the controller registers.
+	 * According to skbuff.h documentation the csum_start element for IP
+	 * checksums is undefined/unsued when ip_summed == CHECKSUM_UNNECESSARY.
+	 * Only CAN skbs can be processed here which already have this property.
+	 */
+
+#define cgw_hops(skb) ((skb)->csum_start)
+
+	BUG_ON(skb->ip_summed != CHECKSUM_UNNECESSARY);
+
+	if (cgw_hops(skb) >= max_hops) {
+		/* indicate deleted frames due to misconfiguration */
+		gwj->deleted_frames++;
 		return;
+	}
 
 	if (!(gwj->dst.dev->flags & IFF_UP)) {
 		gwj->dropped_frames++;
 		return;
 	}
 
+	/* is sending the skb back to the incoming interface not allowed? */
+	if (!(gwj->flags & CGW_FLAGS_CAN_IIF_TX_OK) &&
+	    skb_headroom(skb) == sizeof(struct can_skb_priv) &&
+	    (((struct can_skb_priv *)(skb->head))->ifindex ==
+	     gwj->dst.dev->ifindex))
+		return;
+
 	/*
 	 * clone the given skb, which has not been done in can_rcv()
 	 *
@@ -363,15 +402,8 @@ static void can_can_gw_rcv(struct sk_buff *skb, void *data)
 		return;
 	}
 
-	/*
-	 * Mark routed frames by setting some mac header length which is
-	 * not relevant for the CAN frames located in the skb->data section.
-	 *
-	 * As dev->header_ops is not set in CAN netdevices no one is ever
-	 * accessing the various header offsets in the CAN skbuffs anyway.
-	 * E.g. using the packet socket to read CAN frames is still working.
-	 */
-	skb_set_mac_header(nskb, 8);
+	/* put the incremented hop counter in the cloned skb */
+	cgw_hops(nskb) = cgw_hops(skb) + 1;
 	nskb->dev = gwj->dst.dev;
 
 	/* pointer to modifiable CAN frame */
@@ -472,6 +504,11 @@ static int cgw_put_job(struct sk_buff *skb, struct cgw_job *gwj, int type,
 			goto cancel;
 	}
 
+	if (gwj->deleted_frames) {
+		if (nla_put_u32(skb, CGW_DELETED, gwj->deleted_frames) < 0)
+			goto cancel;
+	}
+
 	/* check non default settings of attributes */
 
 	if (gwj->mod.modtype.and) {
@@ -771,6 +808,7 @@ static int cgw_create_job(struct sk_buff *skb,  struct nlmsghdr *nlh,
 
 	gwj->handled_frames = 0;
 	gwj->dropped_frames = 0;
+	gwj->deleted_frames = 0;
 	gwj->flags = r->flags;
 	gwj->gwtype = r->gwtype;
 
@@ -895,7 +933,11 @@ static int cgw_remove_job(struct sk_buff *skb,  struct nlmsghdr *nlh, void *arg)
 
 static __init int cgw_module_init(void)
 {
-	printk(banner);
+	/* sanitize given module parameter */
+	max_hops = clamp_t(unsigned int, max_hops, CGW_MIN_HOPS, CGW_MAX_HOPS);
+
+	pr_info("can: netlink gateway (rev " CAN_GW_VERSION ") max_hops=%d\n",
+		max_hops);
 
 	cgw_cache = kmem_cache_create("can_gw", sizeof(struct cgw_job),
 				      0, 0, NULL);

net/can/raw.c

@@ -50,6 +50,7 @@
 #include <linux/skbuff.h>
 #include <linux/can.h>
 #include <linux/can/core.h>
+#include <linux/can/skb.h>
 #include <linux/can/raw.h>
 #include <net/sock.h>
 #include <net/net_namespace.h>
@@ -699,11 +700,14 @@ static int raw_sendmsg(struct kiocb *iocb, struct socket *sock,
 	if (!dev)
 		return -ENXIO;
 
-	skb = sock_alloc_send_skb(sk, size, msg->msg_flags & MSG_DONTWAIT,
-				  &err);
+	skb = sock_alloc_send_skb(sk, size + sizeof(struct can_skb_priv),
+				  msg->msg_flags & MSG_DONTWAIT, &err);
 	if (!skb)
 		goto put_dev;
 
+	skb_reserve(skb, sizeof(struct can_skb_priv));
+	((struct can_skb_priv *)(skb->head))->ifindex = dev->ifindex;
+
 	err = memcpy_fromiovec(skb_put(skb, size), msg->msg_iov, size);
 	if (err < 0)
 		goto free_skb;