staging: et131x: Clean up the phy coma stuff

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/staging/et131x/et1310_phy.c

@@ -740,7 +740,7 @@ void et131x_Mii_check(struct et131x_adapter *etdev,
 
 	if (bmsr_ints.bits.link_status) {
 		if (bmsr.bits.link_status) {
-			etdev->PoMgmt.TransPhyComaModeOnBoot = 20;
+			etdev->boot_coma = 20;
 
 			/* Update our state variables and indicate the
 			 * connected state
@@ -831,7 +831,7 @@ void et131x_Mii_check(struct et131x_adapter *etdev,
 			etdev->linkspeed = speed;
 			etdev->duplex_mode = duplex;
 
-			etdev->PoMgmt.TransPhyComaModeOnBoot = 20;
+			etdev->boot_coma = 20;
 
 			if (etdev->linkspeed == TRUEPHY_SPEED_10MBPS) {
 				/*

drivers/staging/et131x/et1310_pm.c

@@ -116,8 +116,8 @@ void EnablePhyComa(struct et131x_adapter *etdev)
 	/* Save the GbE PHY speed and duplex modes. Need to restore this
 	 * when cable is plugged back in
 	 */
-	etdev->PoMgmt.PowerDownSpeed = etdev->AiForceSpeed;
-	etdev->PoMgmt.PowerDownDuplex = etdev->AiForceDpx;
+	etdev->pdown_speed = etdev->AiForceSpeed;
+	etdev->pdown_duplex = etdev->AiForceDpx;
 
 	/* Stop sending packets. */
 	spin_lock_irqsave(&etdev->send_hw_lock, flags);
@@ -153,8 +153,8 @@ void DisablePhyComa(struct et131x_adapter *etdev)
 	/* Restore the GbE PHY speed and duplex modes;
 	 * Reset JAGCore; re-configure and initialize JAGCore and gigE PHY
 	 */
-	etdev->AiForceSpeed = etdev->PoMgmt.PowerDownSpeed;
-	etdev->AiForceDpx = etdev->PoMgmt.PowerDownDuplex;
+	etdev->AiForceSpeed = etdev->pdown_speed;
+	etdev->AiForceDpx = etdev->pdown_duplex;
 
 	/* Re-initialize the send structures */
 	et131x_init_send(etdev);

drivers/staging/et131x/et131x_adapter.h

@@ -145,19 +145,6 @@ typedef struct _ce_stats_t {
 	u32 InterruptStatus;
 } CE_STATS_t, *PCE_STATS_t;
 
-typedef struct _MP_POWER_MGMT {
-	/* variable putting the phy into coma mode when boot up with no cable
-	 * plugged in after 5 seconds
-	 */
-	u8 TransPhyComaModeOnBoot;
-
-	/* Next two used to save power information at power down. This
-	 * information will be used during power up to set up parts of Power
-	 * Management in JAGCore
-	 */
-	u16 PowerDownSpeed;
-	u8 PowerDownDuplex;
-} MP_POWER_MGMT, *PMP_POWER_MGMT;
 
 /* The private adapter structure */
 struct et131x_adapter {
@@ -223,7 +210,19 @@ struct et131x_adapter {
 
 	/* Minimize init-time */
 	struct timer_list ErrorTimer;
-	MP_POWER_MGMT PoMgmt;
+
+	/* variable putting the phy into coma mode when boot up with no cable
+	 * plugged in after 5 seconds
+	 */
+	u8 boot_coma;
+
+	/* Next two used to save power information at power down. This
+	 * information will be used during power up to set up parts of Power
+	 * Management in JAGCore
+	 */
+	u16 pdown_speed;
+	u8 pdown_duplex;
+
 	u32 CachedMaskValue;
 
 	/* Xcvr status at last poll */

drivers/staging/et131x/et131x_initpci.c

@@ -276,11 +276,11 @@ void et131x_error_timer_handler(unsigned long data)
 
 	if (!etdev->Bmsr.bits.link_status &&
 	    etdev->RegistryPhyComa &&
-	    etdev->PoMgmt.TransPhyComaModeOnBoot < 11) {
-		etdev->PoMgmt.TransPhyComaModeOnBoot++;
+	    etdev->boot_coma < 11) {
+		etdev->boot_coma++;
 	}
 
-	if (etdev->PoMgmt.TransPhyComaModeOnBoot == 10) {
+	if (etdev->boot_coma == 10) {
 		if (!etdev->Bmsr.bits.link_status
 		    && etdev->RegistryPhyComa) {
 			if ((pm_csr & ET_PM_PHY_SW_COMA) == 0) {
@@ -728,7 +728,7 @@ static int __devinit et131x_pci_setup(struct pci_dev *pdev,
 
 	/* Initialize variable for counting how long we do not have
 							link status */
-	adapter->PoMgmt.TransPhyComaModeOnBoot = 0;
+	adapter->boot_coma = 0;
 
 	/* We can enable interrupts now
 	 *