Commit 65fd4272 authored by Matthieu CASTET's avatar Matthieu CASTET Committed by Greg Kroah-Hartman

USB: ehci tdi : let's tdi_reset set host mode

tdi_reset is already taking care of setting host mode for tdi devices.
Don't duplicate code in platform driver.

Make ehci_halt a nop if the controller is not in host mode (otherwise it 
will fail), and let's ehci_reset do the tdi_reset.
We need to move hcd->has_tt flags before ehci_halt, in order ehci_halt 
knows we are a tdi device.


Before the setup routine was doing :
- put controller in host mode
- ehci_halt
- ehci_init
- hcd->has_tt = 1;
- ehci_reset

Now we do :
- hcd->has_tt = 1;
- ehci_halt
- ehci_init
- ehci_reset

PS : now we handle correctly the device -> host transition.
Signed-off-by: default avatarMatthieu CASTET <matthieu.castet@parrot.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@suse.de>
parent eabf0f5f
......@@ -233,8 +233,6 @@ static void mpc83xx_usb_setup(struct usb_hcd *hcd)
mpc83xx_setup_phy(ehci, pdata->phy_mode, 1);
}
/* put controller in host mode. */
ehci_writel(ehci, 0x00000003, non_ehci + FSL_SOC_USB_USBMODE);
#ifdef CONFIG_PPC_85xx
out_be32(non_ehci + FSL_SOC_USB_PRICTRL, 0x00000008);
out_be32(non_ehci + FSL_SOC_USB_AGECNTTHRSH, 0x00000080);
......@@ -270,6 +268,8 @@ static int ehci_fsl_setup(struct usb_hcd *hcd)
/* cache this readonly data; minimize chip reads */
ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
hcd->has_tt = 1;
retval = ehci_halt(ehci);
if (retval)
return retval;
......@@ -279,8 +279,6 @@ static int ehci_fsl_setup(struct usb_hcd *hcd)
if (retval)
return retval;
hcd->has_tt = 1;
ehci->sbrn = 0x20;
ehci_reset(ehci);
......
......@@ -27,7 +27,6 @@
#define PORT_PTS_SERIAL (3<<30)
#define PORT_PTS_PTW (1<<28)
#define FSL_SOC_USB_PORTSC2 0x188
#define FSL_SOC_USB_USBMODE 0x1a8
#define FSL_SOC_USB_SNOOP1 0x400 /* NOTE: big-endian */
#define FSL_SOC_USB_SNOOP2 0x404 /* NOTE: big-endian */
#define FSL_SOC_USB_AGECNTTHRSH 0x408 /* NOTE: big-endian */
......
......@@ -194,6 +194,17 @@ static int handshake (struct ehci_hcd *ehci, void __iomem *ptr,
return -ETIMEDOUT;
}
/* check TDI/ARC silicon is in host mode */
static int tdi_in_host_mode (struct ehci_hcd *ehci)
{
u32 __iomem *reg_ptr;
u32 tmp;
reg_ptr = (u32 __iomem *)(((u8 __iomem *)ehci->regs) + USBMODE);
tmp = ehci_readl(ehci, reg_ptr);
return (tmp & 3) == USBMODE_CM_HC;
}
/* force HC to halt state from unknown (EHCI spec section 2.3) */
static int ehci_halt (struct ehci_hcd *ehci)
{
......@@ -202,6 +213,10 @@ static int ehci_halt (struct ehci_hcd *ehci)
/* disable any irqs left enabled by previous code */
ehci_writel(ehci, 0, &ehci->regs->intr_enable);
if (ehci_is_TDI(ehci) && tdi_in_host_mode(ehci) == 0) {
return 0;
}
if ((temp & STS_HALT) != 0)
return 0;
......
......@@ -26,9 +26,6 @@
#include <mach/mxc_ehci.h>
#define ULPI_VIEWPORT_OFFSET 0x170
#define PORTSC_OFFSET 0x184
#define USBMODE_OFFSET 0x1a8
#define USBMODE_CM_HOST 3
struct ehci_mxc_priv {
struct clk *usbclk, *ahbclk;
......@@ -51,6 +48,8 @@ static int ehci_mxc_setup(struct usb_hcd *hcd)
/* cache this readonly data; minimize chip reads */
ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
hcd->has_tt = 1;
retval = ehci_halt(ehci);
if (retval)
return retval;
......@@ -60,8 +59,6 @@ static int ehci_mxc_setup(struct usb_hcd *hcd)
if (retval)
return retval;
hcd->has_tt = 1;
ehci->sbrn = 0x20;
ehci_reset(ehci);
......@@ -191,12 +188,8 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
clk_enable(priv->ahbclk);
}
/* set USBMODE to host mode */
temp = readl(hcd->regs + USBMODE_OFFSET);
writel(temp | USBMODE_CM_HOST, hcd->regs + USBMODE_OFFSET);
/* set up the PORTSCx register */
writel(pdata->portsc, hcd->regs + PORTSC_OFFSET);
ehci_writel(ehci, pdata->portsc, &ehci->regs->port_status[0]);
mdelay(10);
/* setup specific usb hw */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment