Skip to content

L
linux
Commit 67a54566 authored by Daniel Vetter's avatar Daniel Vetter
Browse files
Options

drm/i915: extract intel_dp_init_panel_power_sequencer 

That thing has grown way too big already.

Also move around a comment to the right spot.
Reviewed-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: default avatarPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: default avatarDaniel Vetter <daniel.vetter@ffwll.ch>
parent 6b3ec1c9
Hide whitespace changes
Inline Side-by-side
Showing with 115 additions and 108 deletions
drivers/gpu/drm/i915/intel_dp.c
View file @ 67a54566
......@@ -2522,6 +2522,118 @@ intel_dp_add_properties(struct intel_dp *intel_dp, struct drm_connector *connect
intel_attach_broadcast_rgb_property(connector);
}
static void
intel_dp_init_panel_power_sequencer(struct drm_device *dev,
struct intel_dp *intel_dp)
{
struct drm_i915_private *dev_priv = dev->dev_private;
struct edp_power_seq cur, vbt, spec, final;
u32 pp_on, pp_off, pp_div, pp;
/* Workaround: Need to write PP_CONTROL with the unlock key as
* the very first thing. */
pp = ironlake_get_pp_control(dev_priv);
I915_WRITE(PCH_PP_CONTROL, pp);
pp_on = I915_READ(PCH_PP_ON_DELAYS);
pp_off = I915_READ(PCH_PP_OFF_DELAYS);
pp_div = I915_READ(PCH_PP_DIVISOR);
/* Pull timing values out of registers */
cur.t1_t3 = (pp_on & PANEL_POWER_UP_DELAY_MASK) >>
PANEL_POWER_UP_DELAY_SHIFT;
cur.t8 = (pp_on & PANEL_LIGHT_ON_DELAY_MASK) >>
PANEL_LIGHT_ON_DELAY_SHIFT;
cur.t9 = (pp_off & PANEL_LIGHT_OFF_DELAY_MASK) >>
PANEL_LIGHT_OFF_DELAY_SHIFT;
cur.t10 = (pp_off & PANEL_POWER_DOWN_DELAY_MASK) >>
PANEL_POWER_DOWN_DELAY_SHIFT;
cur.t11_t12 = ((pp_div & PANEL_POWER_CYCLE_DELAY_MASK) >>
PANEL_POWER_CYCLE_DELAY_SHIFT) * 1000;
DRM_DEBUG_KMS("cur t1_t3 %d t8 %d t9 %d t10 %d t11_t12 %d\n",
cur.t1_t3, cur.t8, cur.t9, cur.t10, cur.t11_t12);
vbt = dev_priv->edp.pps;
/* Upper limits from eDP 1.3 spec. Note that we use the clunky units of
* our hw here, which are all in 100usec. */
spec.t1_t3 = 210 * 10;
spec.t8 = 50 * 10; /* no limit for t8, use t7 instead */
spec.t9 = 50 * 10; /* no limit for t9, make it symmetric with t8 */
spec.t10 = 500 * 10;
/* This one is special and actually in units of 100ms, but zero
* based in the hw (so we need to add 100 ms). But the sw vbt
* table multiplies it with 1000 to make it in units of 100usec,
* too. */
spec.t11_t12 = (510 + 100) * 10;
DRM_DEBUG_KMS("vbt t1_t3 %d t8 %d t9 %d t10 %d t11_t12 %d\n",
vbt.t1_t3, vbt.t8, vbt.t9, vbt.t10, vbt.t11_t12);
/* Use the max of the register settings and vbt. If both are
* unset, fall back to the spec limits. */
#define assign_final(field) final.field = (max(cur.field, vbt.field) == 0 ? \
spec.field : \
max(cur.field, vbt.field))
assign_final(t1_t3);
assign_final(t8);
assign_final(t9);
assign_final(t10);
assign_final(t11_t12);
#undef assign_final
#define get_delay(field) (DIV_ROUND_UP(final.field, 10))
intel_dp->panel_power_up_delay = get_delay(t1_t3);
intel_dp->backlight_on_delay = get_delay(t8);
intel_dp->backlight_off_delay = get_delay(t9);
intel_dp->panel_power_down_delay = get_delay(t10);
intel_dp->panel_power_cycle_delay = get_delay(t11_t12);
#undef get_delay
/* And finally store the new values in the power sequencer. */
pp_on = (final.t1_t3 << PANEL_POWER_UP_DELAY_SHIFT) |
(final.t8 << PANEL_LIGHT_ON_DELAY_SHIFT);
pp_off = (final.t9 << PANEL_LIGHT_OFF_DELAY_SHIFT) |
(final.t10 << PANEL_POWER_DOWN_DELAY_SHIFT);
/* Compute the divisor for the pp clock, simply match the Bspec
* formula. */
pp_div = ((100 * intel_pch_rawclk(dev))/2 - 1)
<< PP_REFERENCE_DIVIDER_SHIFT;
pp_div |= (DIV_ROUND_UP(final.t11_t12, 1000)
<< PANEL_POWER_CYCLE_DELAY_SHIFT);
/* Haswell doesn't have any port selection bits for the panel
* power sequencer any more. */
if (HAS_PCH_IBX(dev) || HAS_PCH_CPT(dev)) {
if (is_cpu_edp(intel_dp))
pp_on |= PANEL_POWER_PORT_DP_A;
else
pp_on |= PANEL_POWER_PORT_DP_D;
}
I915_WRITE(PCH_PP_ON_DELAYS, pp_on);
I915_WRITE(PCH_PP_OFF_DELAYS, pp_off);
I915_WRITE(PCH_PP_DIVISOR, pp_div);
DRM_DEBUG_KMS("panel power up delay %d, power down delay %d, power cycle delay %d\n",
intel_dp->panel_power_up_delay, intel_dp->panel_power_down_delay,
intel_dp->panel_power_cycle_delay);
DRM_DEBUG_KMS("backlight on delay %d, off delay %d\n",
intel_dp->backlight_on_delay, intel_dp->backlight_off_delay);
DRM_DEBUG_KMS("panel power sequencer register settings: PP_ON %#x, PP_OFF %#x, PP_DIV %#x\n",
I915_READ(PCH_PP_ON_DELAYS),
I915_READ(PCH_PP_OFF_DELAYS),
I915_READ(PCH_PP_DIVISOR));
}
void
intel_dp_init(struct drm_device *dev, int output_reg, enum port port)
{
......@@ -2636,117 +2748,12 @@ intel_dp_init(struct drm_device *dev, int output_reg, enum port port)
break;
}
/* Cache some DPCD data in the eDP case */
if (is_edp(intel_dp)) {
struct edp_power_seq cur, vbt, spec, final;
u32 pp_on, pp_off, pp_div, pp;
/* Workaround: Need to write PP_CONTROL with the unlock key as
* the very first thing. */
pp = ironlake_get_pp_control(dev_priv);
I915_WRITE(PCH_PP_CONTROL, pp);
pp_on = I915_READ(PCH_PP_ON_DELAYS);
pp_off = I915_READ(PCH_PP_OFF_DELAYS);
pp_div = I915_READ(PCH_PP_DIVISOR);
/* Pull timing values out of registers */
cur.t1_t3 = (pp_on & PANEL_POWER_UP_DELAY_MASK) >>
PANEL_POWER_UP_DELAY_SHIFT;
cur.t8 = (pp_on & PANEL_LIGHT_ON_DELAY_MASK) >>
PANEL_LIGHT_ON_DELAY_SHIFT;
cur.t9 = (pp_off & PANEL_LIGHT_OFF_DELAY_MASK) >>
PANEL_LIGHT_OFF_DELAY_SHIFT;
cur.t10 = (pp_off & PANEL_POWER_DOWN_DELAY_MASK) >>
PANEL_POWER_DOWN_DELAY_SHIFT;
cur.t11_t12 = ((pp_div & PANEL_POWER_CYCLE_DELAY_MASK) >>
PANEL_POWER_CYCLE_DELAY_SHIFT) * 1000;
DRM_DEBUG_KMS("cur t1_t3 %d t8 %d t9 %d t10 %d t11_t12 %d\n",
cur.t1_t3, cur.t8, cur.t9, cur.t10, cur.t11_t12);
vbt = dev_priv->edp.pps;
/* Upper limits from eDP 1.3 spec. Note that we use the clunky
* units of our hw here, which are all in 100usec. */
spec.t1_t3 = 210 * 10;
spec.t8 = 50 * 10; /* no limit for t8, use t7 instead */
spec.t9 = 50 * 10; /* no limit for t9, make it symmetric with t8 */
spec.t10 = 500 * 10;
/* This one is special and actually in units of 100ms, but zero
* based in the hw (so we need to add 100 ms). But the sw vbt
* table multiplies it with 1000 to make it in units of 100usec,
* too. */
spec.t11_t12 = (510 + 100) * 10;
DRM_DEBUG_KMS("vbt t1_t3 %d t8 %d t9 %d t10 %d t11_t12 %d\n",
vbt.t1_t3, vbt.t8, vbt.t9, vbt.t10, vbt.t11_t12);
/* Use the max of the register settings and vbt. If both are
* unset, fall back to the spec limits. */
#define assign_final(field) final.field = (max(cur.field, vbt.field) == 0 ? \
spec.field : \
max(cur.field, vbt.field))
assign_final(t1_t3);
assign_final(t8);
assign_final(t9);
assign_final(t10);
assign_final(t11_t12);
#undef assign_final
#define get_delay(field) (DIV_ROUND_UP(final.field, 10))
intel_dp->panel_power_up_delay = get_delay(t1_t3);
intel_dp->backlight_on_delay = get_delay(t8);
intel_dp->backlight_off_delay = get_delay(t9);
intel_dp->panel_power_down_delay = get_delay(t10);
intel_dp->panel_power_cycle_delay = get_delay(t11_t12);
#undef get_delay
/* And finally store the new values in the power sequencer. */
pp_on = (final.t1_t3 << PANEL_POWER_UP_DELAY_SHIFT) |
(final.t8 << PANEL_LIGHT_ON_DELAY_SHIFT);
pp_off = (final.t9 << PANEL_LIGHT_OFF_DELAY_SHIFT) |
(final.t10 << PANEL_POWER_DOWN_DELAY_SHIFT);
/* Compute the divisor for the pp clock, simply match the Bspec
* formula. */
pp_div = ((100 * intel_pch_rawclk(dev))/2 - 1)
<< PP_REFERENCE_DIVIDER_SHIFT;
pp_div |= (DIV_ROUND_UP(final.t11_t12, 1000)
<< PANEL_POWER_CYCLE_DELAY_SHIFT);
/* Haswell doesn't have any port selection bits for the panel
* power sequence any more. */
if (HAS_PCH_IBX(dev) || HAS_PCH_CPT(dev)) {
if (is_cpu_edp(intel_dp))
pp_on |= PANEL_POWER_PORT_DP_A;
else
pp_on |= PANEL_POWER_PORT_DP_D;
}
I915_WRITE(PCH_PP_ON_DELAYS, pp_on);
I915_WRITE(PCH_PP_OFF_DELAYS, pp_off);
I915_WRITE(PCH_PP_DIVISOR, pp_div);
DRM_DEBUG_KMS("panel power up delay %d, power down delay %d, power cycle delay %d\n",
intel_dp->panel_power_up_delay, intel_dp->panel_power_down_delay,
intel_dp->panel_power_cycle_delay);
DRM_DEBUG_KMS("backlight on delay %d, off delay %d\n",
intel_dp->backlight_on_delay, intel_dp->backlight_off_delay);
DRM_DEBUG_KMS("panel power sequencer register settings: PP_ON %#x, PP_OFF %#x, PP_DIV %#x\n",
I915_READ(PCH_PP_ON_DELAYS),
I915_READ(PCH_PP_OFF_DELAYS),
I915_READ(PCH_PP_DIVISOR));
}
if (is_edp(intel_dp))
intel_dp_init_panel_power_sequencer(dev, intel_dp);
intel_dp_i2c_init(intel_dp, intel_connector, name);
/* Cache DPCD and EDID for edp. */
if (is_edp(intel_dp)) {
bool ret;
struct drm_display_mode *scan;
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7