ARM: dts: imx7d-sdb: Add Wifi support

imx7d-sdb has a BCM4339 Wifi chip connected to USDHC2.

Add support for it.

While at it, move the WL_REG_ON pin to the correct pinctrl node.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arch/arm/boot/dts/imx7d-sdb.dts

@@ -105,6 +105,18 @@ reg_vref_1v8: regulator-vref-1v8 {
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
 	};
+
+	reg_brcm: regulator-brcm {
+		compatible = "regulator-fixed";
+		gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-name = "brcm_reg";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_brcm_reg>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <200000>;
+	};
 };
 
 &adc1 {
@@ -379,6 +391,19 @@ &usdhc1 {
 	status = "okay";
 };
 
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	wakeup-source;
+	keep-power-in-suspend;
+	non-removable;
+	vmmc-supply = <&reg_brcm>;
+	fsl,tuning-step = <2>;
+	status = "okay";
+};
+
 &usdhc3 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc3>;
@@ -403,6 +428,12 @@ &iomuxc {
 	pinctrl-0 = <&pinctrl_hog>;
 
 	imx7d-sdb {
+		pinctrl_brcm_reg: brcmreggrp {
+			fsl,pins = <
+				MX7D_PAD_ECSPI2_MOSI__GPIO4_IO21	0x14
+			>;
+		};
+
 		pinctrl_ecspi3: ecspi3grp {
 			fsl,pins = <
 				MX7D_PAD_SAI2_TX_SYNC__ECSPI3_MISO	0x2
@@ -570,7 +601,6 @@ MX7D_PAD_SD2_DATA0__SD2_DATA0		0x59
 				MX7D_PAD_SD2_DATA1__SD2_DATA1		0x59
 				MX7D_PAD_SD2_DATA2__SD2_DATA2		0x59
 				MX7D_PAD_SD2_DATA3__SD2_DATA3		0x59
-				MX7D_PAD_ECSPI2_MOSI__GPIO4_IO21	0x59 /* WL_REG_ON */
 			>;
 		};