Commit 6f65daed authored by Bjorn Helgaas's avatar Bjorn Helgaas

Merge branch 'pci/host-faraday' into next

* pci/host-faraday:
  PCI: faraday: Add clock handling
  PCI: faraday: Add clock bindings
parents ecf75c46 2eeb02b2
......@@ -30,6 +30,13 @@ Mandatory properties:
128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked as
pre-fetchable.
Optional properties:
- clocks: when present, this should contain the peripheral clock (PCLK) and the
PCI clock (PCICLK). If these are not present, they are assumed to be
hard-wired enabled and always on. The PCI clock will be 33 or 66 MHz.
- clock-names: when present, this should contain "PCLK" for the peripheral
clock and "PCICLK" for the PCI-side clock.
Mandatory subnodes:
- For "faraday,ftpci100" a node representing the interrupt-controller inside the
host bridge is mandatory. It has the following mandatory properties:
......
......@@ -25,6 +25,7 @@
#include <linux/irqchip/chained_irq.h>
#include <linux/bitops.h>
#include <linux/irq.h>
#include <linux/clk.h>
/*
* Special configuration registers directly in the first few words
......@@ -37,6 +38,7 @@
#define PCI_CONFIG 0x28 /* PCI configuration command register */
#define PCI_DATA 0x2C
#define FARADAY_PCI_STATUS_CMD 0x04 /* Status and command */
#define FARADAY_PCI_PMC 0x40 /* Power management control */
#define FARADAY_PCI_PMCSR 0x44 /* Power management status */
#define FARADAY_PCI_CTRL1 0x48 /* Control register 1 */
......@@ -45,6 +47,8 @@
#define FARADAY_PCI_MEM2_BASE_SIZE 0x54 /* Memory base and size #2 */
#define FARADAY_PCI_MEM3_BASE_SIZE 0x58 /* Memory base and size #3 */
#define PCI_STATUS_66MHZ_CAPABLE BIT(21)
/* Bits 31..28 gives INTD..INTA status */
#define PCI_CTRL2_INTSTS_SHIFT 28
#define PCI_CTRL2_INTMASK_CMDERR BIT(27)
......@@ -117,6 +121,7 @@ struct faraday_pci {
void __iomem *base;
struct irq_domain *irqdomain;
struct pci_bus *bus;
struct clk *bus_clk;
};
static int faraday_res_to_memcfg(resource_size_t mem_base,
......@@ -444,6 +449,9 @@ static int faraday_pci_probe(struct platform_device *pdev)
struct resource *mem;
struct resource *io;
struct pci_host_bridge *host;
struct clk *clk;
unsigned char max_bus_speed = PCI_SPEED_33MHz;
unsigned char cur_bus_speed = PCI_SPEED_33MHz;
int ret;
u32 val;
LIST_HEAD(res);
......@@ -462,6 +470,24 @@ static int faraday_pci_probe(struct platform_device *pdev)
host->sysdata = p;
p->dev = dev;
/* Retrieve and enable optional clocks */
clk = devm_clk_get(dev, "PCLK");
if (IS_ERR(clk))
return PTR_ERR(clk);
ret = clk_prepare_enable(clk);
if (ret) {
dev_err(dev, "could not prepare PCLK\n");
return ret;
}
p->bus_clk = devm_clk_get(dev, "PCICLK");
if (IS_ERR(p->bus_clk))
return PTR_ERR(clk);
ret = clk_prepare_enable(p->bus_clk);
if (ret) {
dev_err(dev, "could not prepare PCICLK\n");
return ret;
}
regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
p->base = devm_ioremap_resource(dev, regs);
if (IS_ERR(p->base))
......@@ -524,6 +550,34 @@ static int faraday_pci_probe(struct platform_device *pdev)
}
}
/* Check bus clock if we can gear up to 66 MHz */
if (!IS_ERR(p->bus_clk)) {
unsigned long rate;
u32 val;
faraday_raw_pci_read_config(p, 0, 0,
FARADAY_PCI_STATUS_CMD, 4, &val);
rate = clk_get_rate(p->bus_clk);
if ((rate == 33000000) && (val & PCI_STATUS_66MHZ_CAPABLE)) {
dev_info(dev, "33MHz bus is 66MHz capable\n");
max_bus_speed = PCI_SPEED_66MHz;
ret = clk_set_rate(p->bus_clk, 66000000);
if (ret)
dev_err(dev, "failed to set bus clock\n");
} else {
dev_info(dev, "33MHz only bus\n");
max_bus_speed = PCI_SPEED_33MHz;
}
/* Bumping the clock may fail so read back the rate */
rate = clk_get_rate(p->bus_clk);
if (rate == 33000000)
cur_bus_speed = PCI_SPEED_33MHz;
if (rate == 66000000)
cur_bus_speed = PCI_SPEED_66MHz;
}
ret = faraday_pci_parse_map_dma_ranges(p, dev->of_node);
if (ret)
return ret;
......@@ -535,6 +589,8 @@ static int faraday_pci_probe(struct platform_device *pdev)
return ret;
}
p->bus = host->bus;
p->bus->max_bus_speed = max_bus_speed;
p->bus->cur_bus_speed = cur_bus_speed;
pci_bus_assign_resources(p->bus);
pci_bus_add_devices(p->bus);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment