mtd: add LPC32xx MLC NAND driver

This patch adds a driver for the MLC NAND controller of the LPC32xx SoC.

[dwmw2: 21st century pedantry]
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt

+NXP LPC32xx SoC NAND MLC controller
+
+Required properties:
+- compatible: "nxp,lpc3220-mlc"
+- reg: Address and size of the controller
+- interrupts: The NAND interrupt specification
+- gpios: GPIO specification for NAND write protect
+
+The following required properties are very controller specific. See the LPC32xx
+User Manual 7.5.14 MLC NAND Timing Register (the values here are specified in
+Hz, to make them independent of actual clock speed and to provide for good
+accuracy:)
+- nxp,tcea_delay: TCEA_DELAY
+- nxp,busy_delay: BUSY_DELAY
+- nxp,nand_ta: NAND_TA
+- nxp,rd_high: RD_HIGH
+- nxp,rd_low: RD_LOW
+- nxp,wr_high: WR_HIGH
+- nxp,wr_low: WR_LOW
+
+Optional subnodes:
+- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt
+
+Example:
+
+	mlc: flash@200A8000 {
+		compatible = "nxp,lpc3220-mlc";
+		reg = <0x200A8000 0x11000>;
+		interrupts = <11 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nxp,tcea-delay = <333333333>;
+		nxp,busy-delay = <10000000>;
+		nxp,nand-ta = <18181818>;
+		nxp,rd-high = <31250000>;
+		nxp,rd-low = <45454545>;
+		nxp,wr-high = <40000000>;
+		nxp,wr-low = <83333333>;
+		gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+		mtd0@00000000 {
+			label = "boot";
+			reg = <0x00000000 0x00064000>;
+			read-only;
+		};
+
+		...
+
+	};

drivers/mtd/nand/Kconfig

@@ -425,6 +425,17 @@ config MTD_NAND_SLC_LPC32XX
 	  Please check the actual NAND chip connected and its support
 	  by the SLC NAND controller.
 
+config MTD_NAND_MLC_LPC32XX
+	tristate "NXP LPC32xx MLC Controller"
+	depends on ARCH_LPC32XX
+	help
+	  Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND
+	  controller. This is the default for the WORK92105 controller
+	  board.
+
+	  Please check the actual NAND chip connected and its support
+	  by the MLC NAND controller.
+
 config MTD_NAND_CM_X270
 	tristate "Support for NAND Flash on CM-X270 modules"
 	depends on MACH_ARMCORE

drivers/mtd/nand/Makefile

@@ -41,6 +41,7 @@ obj-$(CONFIG_MTD_NAND_FSL_ELBC)		+= fsl_elbc_nand.o
 obj-$(CONFIG_MTD_NAND_FSL_IFC)		+= fsl_ifc_nand.o
 obj-$(CONFIG_MTD_NAND_FSL_UPM)		+= fsl_upm.o
 obj-$(CONFIG_MTD_NAND_SLC_LPC32XX)      += lpc32xx_slc.o
+obj-$(CONFIG_MTD_NAND_MLC_LPC32XX)      += lpc32xx_mlc.o
 obj-$(CONFIG_MTD_NAND_SH_FLCTL)		+= sh_flctl.o
 obj-$(CONFIG_MTD_NAND_MXC)		+= mxc_nand.o
 obj-$(CONFIG_MTD_NAND_SOCRATES)		+= socrates_nand.o