Merge branch 'spi/next' of git://git.secretlab.ca/git/linux-2.6

* 'spi/next' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
  spi/imx: add device tree probe support
  spi/imx: copy gpio number passed by platform data into driver private data
  spi/imx: use soc name in spi device type naming scheme
  spi/imx: merge type SPI_IMX_VER_0_7 into SPI_IMX_VER_0_4
  spi/imx: do not use spi_imx2_3 to name SPI_IMX_VER_2_3 function and macro
  spi/imx: use mx21 to name SPI_IMX_VER_0_0 function and macro
  spi/imx: do not make copy of spi_imx_devtype_data
  spi/dw: Add spi number into spi irq desc
  spi/tegra: Use engineering names in DT compatible property
  spi/fsl_spi: fix CPM spi driver
  mach-s3c2410: remove unused spi-gpio.h file
  spi: remove obsolete spi-s3c24xx-gpio driver
  mach-gta2: remove unused spi-gpio.h include
  mach-qt2410: convert to spi_gpio
  mach-jive: convert to spi_gpio
  spi/pxa2xx: Remove unavailable ssp_type from documentation
  spi/bfin_spi: uninline fat queue funcs
  spi/bfin_spi: constify pin array
  spi/bfin_spi: use structs for accessing hardware regs
  spi/topcliff-pch: Support new device ML7223 IOH
  ...

Fix up trivial conflict in arch/arm/mach-ep93xx/Makefile

Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt

+* Freescale (Enhanced) Configurable Serial Peripheral Interface
+  (CSPI/eCSPI) for i.MX
+
+Required properties:
+- compatible : Should be "fsl,<soc>-cspi" or "fsl,<soc>-ecspi"
+- reg : Offset and length of the register set for the device
+- interrupts : Should contain CSPI/eCSPI interrupt
+- fsl,spi-num-chipselects : Contains the number of the chipselect
+- cs-gpios : Specifies the gpio pins to be used for chipselects.
+
+Example:
+
+ecspi@70010000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx51-ecspi";
+	reg = <0x70010000 0x4000>;
+	interrupts = <36>;
+	fsl,spi-num-chipselects = <2>;
+	cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */
+		   <&gpio3 25 0>; /* GPIO4_25 */
+};

Documentation/devicetree/bindings/spi/spi_nvidia.txt

+NVIDIA Tegra 2 SPI device
+
+Required properties:
+- compatible : should be "nvidia,tegra20-spi".
+- gpios : should specify GPIOs used for chipselect.

Documentation/spi/ep93xx_spi

@@ -88,6 +88,16 @@ static void __init ts72xx_init_machine(void)
 			    ARRAY_SIZE(ts72xx_spi_devices));
 }
 
+The driver can use DMA for the transfers also. In this case ts72xx_spi_info
+becomes:
+
+static struct ep93xx_spi_info ts72xx_spi_info = {
+	.num_chipselect	= ARRAY_SIZE(ts72xx_spi_devices),
+	.use_dma	= true;
+};
+
+Note that CONFIG_EP93XX_DMA should be enabled as well.
+
 Thanks to
 =========
 Martin Guy, H. Hartley Sweeten and others who helped me during development of

Documentation/spi/pxa2xx

@@ -22,15 +22,11 @@ Typically a SPI master is defined in the arch/.../mach-*/board-*.c as a
 found in include/linux/spi/pxa2xx_spi.h:
 
 struct pxa2xx_spi_master {
-	enum pxa_ssp_type ssp_type;
 	u32 clock_enable;
 	u16 num_chipselect;
 	u8 enable_dma;
 };
 
-The "pxa2xx_spi_master.ssp_type" field must have a value between 1 and 3 and
-informs the driver which features a particular SSP supports.
-
 The "pxa2xx_spi_master.clock_enable" field is used to enable/disable the
 corresponding SSP peripheral block in the "Clock Enable Register (CKEN"). See
 the "PXA2xx Developer Manual" section "Clocks and Power Management".
@@ -61,7 +57,6 @@ static struct resource pxa_spi_nssp_resources[] = {
 };
 
 static struct pxa2xx_spi_master pxa_nssp_master_info = {
-	.ssp_type = PXA25x_NSSP, /* Type of SSP */
 	.clock_enable = CKEN_NSSP, /* NSSP Peripheral clock */
 	.num_chipselect = 1, /* Matches the number of chips attached to NSSP */
 	.enable_dma = 1, /* Enables NSSP DMA */

arch/arm/mach-ep93xx/Makefile

 #
 # Makefile for the linux kernel.
 #
-obj-y			:= core.o clock.o dma-m2p.o
+obj-y			:= core.o clock.o
 obj-m			:=
 obj-n			:=
 obj-			:=
 
+obj-$(CONFIG_EP93XX_DMA)	+= dma.o
+
 obj-$(CONFIG_MACH_ADSSPHERE)	+= adssphere.o
 obj-$(CONFIG_MACH_EDB93XX)	+= edb93xx.o
 obj-$(CONFIG_MACH_GESBC9312)	+= gesbc9312.o

arch/arm/mach-ep93xx/core.c

@@ -506,11 +506,15 @@ static struct resource ep93xx_spi_resources[] = {
 	},
 };
 
+static u64 ep93xx_spi_dma_mask = DMA_BIT_MASK(32);
+
 static struct platform_device ep93xx_spi_device = {
 	.name		= "ep93xx-spi",
 	.id		= 0,
 	.dev		= {
-		.platform_data = &ep93xx_spi_master_data,
+		.platform_data		= &ep93xx_spi_master_data,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.dma_mask		= &ep93xx_spi_dma_mask,
 	},
 	.num_resources	= ARRAY_SIZE(ep93xx_spi_resources),
 	.resource	= ep93xx_spi_resources,

arch/arm/mach-ep93xx/dma.c

+/*
+ * arch/arm/mach-ep93xx/dma.c
+ *
+ * Platform support code for the EP93xx dmaengine driver.
+ *
+ * Copyright (C) 2011 Mika Westerberg
+ *
+ * This work is based on the original dma-m2p implementation with
+ * following copyrights:
+ *
+ *   Copyright (C) 2006 Lennert Buytenhek <buytenh@wantstofly.org>
+ *   Copyright (C) 2006 Applied Data Systems
+ *   Copyright (C) 2009 Ryan Mallon <rmallon@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or (at
+ * your option) any later version.
+ */
+
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+
+#include <mach/dma.h>
+#include <mach/hardware.h>
+
+#define DMA_CHANNEL(_name, _base, _irq) \
+	{ .name = (_name), .base = (_base), .irq = (_irq) }
+
+/*
+ * DMA M2P channels.
+ *
+ * On the EP93xx chip the following peripherals my be allocated to the 10
+ * Memory to Internal Peripheral (M2P) channels (5 transmit + 5 receive).
+ *
+ *	I2S	contains 3 Tx and 3 Rx DMA Channels
+ *	AAC	contains 3 Tx and 3 Rx DMA Channels
+ *	UART1	contains 1 Tx and 1 Rx DMA Channels
+ *	UART2	contains 1 Tx and 1 Rx DMA Channels
+ *	UART3	contains 1 Tx and 1 Rx DMA Channels
+ *	IrDA	contains 1 Tx and 1 Rx DMA Channels
+ *
+ * Registers are mapped statically in ep93xx_map_io().
+ */
+static struct ep93xx_dma_chan_data ep93xx_dma_m2p_channels[] = {
+	DMA_CHANNEL("m2p0", EP93XX_DMA_BASE + 0x0000, IRQ_EP93XX_DMAM2P0),
+	DMA_CHANNEL("m2p1", EP93XX_DMA_BASE + 0x0040, IRQ_EP93XX_DMAM2P1),
+	DMA_CHANNEL("m2p2", EP93XX_DMA_BASE + 0x0080, IRQ_EP93XX_DMAM2P2),
+	DMA_CHANNEL("m2p3", EP93XX_DMA_BASE + 0x00c0, IRQ_EP93XX_DMAM2P3),
+	DMA_CHANNEL("m2p4", EP93XX_DMA_BASE + 0x0240, IRQ_EP93XX_DMAM2P4),
+	DMA_CHANNEL("m2p5", EP93XX_DMA_BASE + 0x0200, IRQ_EP93XX_DMAM2P5),
+	DMA_CHANNEL("m2p6", EP93XX_DMA_BASE + 0x02c0, IRQ_EP93XX_DMAM2P6),
+	DMA_CHANNEL("m2p7", EP93XX_DMA_BASE + 0x0280, IRQ_EP93XX_DMAM2P7),
+	DMA_CHANNEL("m2p8", EP93XX_DMA_BASE + 0x0340, IRQ_EP93XX_DMAM2P8),
+	DMA_CHANNEL("m2p9", EP93XX_DMA_BASE + 0x0300, IRQ_EP93XX_DMAM2P9),
+};
+
+static struct ep93xx_dma_platform_data ep93xx_dma_m2p_data = {
+	.channels		= ep93xx_dma_m2p_channels,
+	.num_channels		= ARRAY_SIZE(ep93xx_dma_m2p_channels),
+};
+
+static struct platform_device ep93xx_dma_m2p_device = {
+	.name			= "ep93xx-dma-m2p",
+	.id			= -1,
+	.dev			= {
+		.platform_data	= &ep93xx_dma_m2p_data,
+	},
+};
+
+/*
+ * DMA M2M channels.
+ *
+ * There are 2 M2M channels which support memcpy/memset and in addition simple
+ * hardware requests from/to SSP and IDE. We do not implement an external
+ * hardware requests.
+ *
+ * Registers are mapped statically in ep93xx_map_io().
+ */
+static struct ep93xx_dma_chan_data ep93xx_dma_m2m_channels[] = {
+	DMA_CHANNEL("m2m0", EP93XX_DMA_BASE + 0x0100, IRQ_EP93XX_DMAM2M0),
+	DMA_CHANNEL("m2m1", EP93XX_DMA_BASE + 0x0140, IRQ_EP93XX_DMAM2M1),
+};
+
+static struct ep93xx_dma_platform_data ep93xx_dma_m2m_data = {
+	.channels		= ep93xx_dma_m2m_channels,
+	.num_channels		= ARRAY_SIZE(ep93xx_dma_m2m_channels),
+};
+
+static struct platform_device ep93xx_dma_m2m_device = {
+	.name			= "ep93xx-dma-m2m",
+	.id			= -1,
+	.dev			= {
+		.platform_data	= &ep93xx_dma_m2m_data,
+	},
+};
+
+static int __init ep93xx_dma_init(void)
+{
+	platform_device_register(&ep93xx_dma_m2p_device);
+	platform_device_register(&ep93xx_dma_m2m_device);
+	return 0;
+}
+arch_initcall(ep93xx_dma_init);

arch/arm/mach-ep93xx/include/mach/dma.h

-/**
- * DOC: EP93xx DMA M2P memory to peripheral and peripheral to memory engine
- *
- * The EP93xx DMA M2P subsystem handles DMA transfers between memory and
- * peripherals. DMA M2P channels are available for audio, UARTs and IrDA.
- * See chapter 10 of the EP93xx users guide for full details on the DMA M2P
- * engine.
- *
- * See sound/soc/ep93xx/ep93xx-pcm.c for an example use of the DMA M2P code.
- *
- */
-
 #ifndef __ASM_ARCH_DMA_H
 #define __ASM_ARCH_DMA_H
 
-#include <linux/list.h>
 #include <linux/types.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
 
-/**
- * struct ep93xx_dma_buffer - Information about a buffer to be transferred
- * using the DMA M2P engine
+/*
+ * M2P channels.
  *
- * @list: Entry in DMA buffer list
- * @bus_addr: Physical address of the buffer
- * @size: Size of the buffer in bytes
+ * Note that these values are also directly used for setting the PPALLOC
+ * register.
  */
-struct ep93xx_dma_buffer {
-	struct list_head	list;
-	u32			bus_addr;
-	u16			size;
-};
+#define EP93XX_DMA_I2S1		0
+#define EP93XX_DMA_I2S2		1
+#define EP93XX_DMA_AAC1		2
+#define EP93XX_DMA_AAC2		3
+#define EP93XX_DMA_AAC3		4
+#define EP93XX_DMA_I2S3		5
+#define EP93XX_DMA_UART1	6
+#define EP93XX_DMA_UART2	7
+#define EP93XX_DMA_UART3	8
+#define EP93XX_DMA_IRDA		9
+/* M2M channels */
+#define EP93XX_DMA_SSP		10
+#define EP93XX_DMA_IDE		11
 
 /**
- * struct ep93xx_dma_m2p_client - Information about a DMA M2P client
- *
- * @name: Unique name for this client
- * @flags: Client flags
- * @cookie: User data to pass to callback functions
- * @buffer_started: Non NULL function to call when a transfer is started.
- * 			The arguments are the user data cookie and the DMA
- *			buffer which is starting.
- * @buffer_finished: Non NULL function to call when a transfer is completed.
- *			The arguments are the user data cookie, the DMA buffer
- *			which has completed, and a boolean flag indicating if
- *			the transfer had an error.
+ * struct ep93xx_dma_data - configuration data for the EP93xx dmaengine
+ * @port: peripheral which is requesting the channel
+ * @direction: TX/RX channel
+ * @name: optional name for the channel, this is displayed in /proc/interrupts
+ *
+ * This information is passed as private channel parameter in a filter
+ * function. Note that this is only needed for slave/cyclic channels.  For
+ * memcpy channels %NULL data should be passed.
  */
-struct ep93xx_dma_m2p_client {
-	char			*name;
-	u8			flags;
-	void			*cookie;
-	void			(*buffer_started)(void *cookie,
-					struct ep93xx_dma_buffer *buf);
-	void			(*buffer_finished)(void *cookie,
-					struct ep93xx_dma_buffer *buf,
-					int bytes, int error);
-
-	/* private: Internal use only */
-	void			*channel;
+struct ep93xx_dma_data {
+	int				port;
+	enum dma_data_direction		direction;
+	const char			*name;
 };
 
-/* DMA M2P ports */
-#define EP93XX_DMA_M2P_PORT_I2S1	0x00
-#define EP93XX_DMA_M2P_PORT_I2S2	0x01
-#define EP93XX_DMA_M2P_PORT_AAC1	0x02
-#define EP93XX_DMA_M2P_PORT_AAC2	0x03
-#define EP93XX_DMA_M2P_PORT_AAC3	0x04
-#define EP93XX_DMA_M2P_PORT_I2S3	0x05
-#define EP93XX_DMA_M2P_PORT_UART1	0x06
-#define EP93XX_DMA_M2P_PORT_UART2	0x07
-#define EP93XX_DMA_M2P_PORT_UART3	0x08
-#define EP93XX_DMA_M2P_PORT_IRDA	0x09
-#define EP93XX_DMA_M2P_PORT_MASK	0x0f
-
-/* DMA M2P client flags */
-#define EP93XX_DMA_M2P_TX		0x00	/* Memory to peripheral */
-#define EP93XX_DMA_M2P_RX		0x10	/* Peripheral to memory */
-
-/*
- * DMA M2P client error handling flags. See the EP93xx users guide
- * documentation on the DMA M2P CONTROL register for more details
- */
-#define EP93XX_DMA_M2P_ABORT_ON_ERROR	0x20	/* Abort on peripheral error */
-#define EP93XX_DMA_M2P_IGNORE_ERROR	0x40	/* Ignore peripheral errors */
-#define EP93XX_DMA_M2P_ERROR_MASK	0x60	/* Mask of error bits */
-
 /**
- * ep93xx_dma_m2p_client_register - Register a client with the DMA M2P
- * subsystem
- *
- * @m2p: Client information to register
- * returns 0 on success
- *
- * The DMA M2P subsystem allocates a channel and an interrupt line for the DMA
- * client
+ * struct ep93xx_dma_chan_data - platform specific data for a DMA channel
+ * @name: name of the channel, used for getting the right clock for the channel
+ * @base: mapped registers
+ * @irq: interrupt number used by this channel
  */
-int ep93xx_dma_m2p_client_register(struct ep93xx_dma_m2p_client *m2p);
+struct ep93xx_dma_chan_data {
+	const char			*name;
+	void __iomem			*base;
+	int				irq;
+};
 
 /**
- * ep93xx_dma_m2p_client_unregister - Unregister a client from the DMA M2P
- * subsystem
- *
- * @m2p: Client to unregister
+ * struct ep93xx_dma_platform_data - platform data for the dmaengine driver
+ * @channels: array of channels which are passed to the driver
+ * @num_channels: number of channels in the array
  *
- * Any transfers currently in progress will be completed in hardware, but
- * ignored in software.
+ * This structure is passed to the DMA engine driver via platform data. For
+ * M2P channels, contract is that even channels are for TX and odd for RX.
+ * There is no requirement for the M2M channels.
  */
-void ep93xx_dma_m2p_client_unregister(struct ep93xx_dma_m2p_client *m2p);
+struct ep93xx_dma_platform_data {
+	struct ep93xx_dma_chan_data	*channels;
+	size_t				num_channels;
+};
 
-/**
- * ep93xx_dma_m2p_submit - Submit a DMA M2P transfer
- *
- * @m2p: DMA Client to submit the transfer on
- * @buf: DMA Buffer to submit
- *
- * If the current or next transfer positions are free on the M2P client then
- * the transfer is started immediately. If not, the transfer is added to the
- * list of pending transfers. This function must not be called from the
- * buffer_finished callback for an M2P channel.
- *
- */
-void ep93xx_dma_m2p_submit(struct ep93xx_dma_m2p_client *m2p,
-			   struct ep93xx_dma_buffer *buf);
+static inline bool ep93xx_dma_chan_is_m2p(struct dma_chan *chan)
+{
+	return !strcmp(dev_name(chan->device->dev), "ep93xx-dma-m2p");
+}
 
 /**
- * ep93xx_dma_m2p_submit_recursive - Put a DMA transfer on the pending list
- * for an M2P channel
+ * ep93xx_dma_chan_direction - returns direction the channel can be used
+ * @chan: channel
  *
- * @m2p: DMA Client to submit the transfer on
- * @buf: DMA Buffer to submit
- *
- * This function must only be called from the buffer_finished callback for an
- * M2P channel. It is commonly used to add the next transfer in a chained list
- * of DMA transfers.
+ * This function can be used in filter functions to find out whether the
+ * channel supports given DMA direction. Only M2P channels have such
+ * limitation, for M2M channels the direction is configurable.
  */
-void ep93xx_dma_m2p_submit_recursive(struct ep93xx_dma_m2p_client *m2p,
-				     struct ep93xx_dma_buffer *buf);
+static inline enum dma_data_direction
+ep93xx_dma_chan_direction(struct dma_chan *chan)
+{
+	if (!ep93xx_dma_chan_is_m2p(chan))
+		return DMA_NONE;
 
-/**
- * ep93xx_dma_m2p_flush - Flush all pending transfers on a DMA M2P client
- *
- * @m2p: DMA client to flush transfers on
- *
- * Any transfers currently in progress will be completed in hardware, but
- * ignored in software.
- *
- */
-void ep93xx_dma_m2p_flush(struct ep93xx_dma_m2p_client *m2p);
+	/* even channels are for TX, odd for RX */
+	return (chan->chan_id % 2 == 0) ? DMA_TO_DEVICE : DMA_FROM_DEVICE;
+}
 
 #endif /* __ASM_ARCH_DMA_H */

arch/arm/mach-ep93xx/include/mach/ep93xx_spi.h

@@ -7,9 +7,11 @@ struct spi_device;
  * struct ep93xx_spi_info - EP93xx specific SPI descriptor
  * @num_chipselect: number of chip selects on this board, must be
  *                  at least one
+ * @use_dma: use DMA for the transfers
  */
 struct ep93xx_spi_info {
 	int	num_chipselect;
+	bool	use_dma;
 };
 
 /**

arch/arm/mach-imx/clock-imx25.c

@@ -282,9 +282,10 @@ static struct clk_lookup lookups[] = {
 	_REGISTER_CLOCK("mxc-ehci.2", "usb", usbotg_clk)
 	_REGISTER_CLOCK("fsl-usb2-udc", "usb", usbotg_clk)
 	_REGISTER_CLOCK("mxc_nand.0", NULL, nfc_clk)
-	_REGISTER_CLOCK("imx25-cspi.0", NULL, cspi1_clk)
-	_REGISTER_CLOCK("imx25-cspi.1", NULL, cspi2_clk)
-	_REGISTER_CLOCK("imx25-cspi.2", NULL, cspi3_clk)
+	/* i.mx25 has the i.mx35 type cspi */
+	_REGISTER_CLOCK("imx35-cspi.0", NULL, cspi1_clk)
+	_REGISTER_CLOCK("imx35-cspi.1", NULL, cspi2_clk)
+	_REGISTER_CLOCK("imx35-cspi.2", NULL, cspi3_clk)
 	_REGISTER_CLOCK("mxc_pwm.0", NULL, pwm1_clk)
 	_REGISTER_CLOCK("mxc_pwm.1", NULL, pwm2_clk)
 	_REGISTER_CLOCK("mxc_pwm.2", NULL, pwm3_clk)

arch/arm/mach-mx5/clock-mx51-mx53.c

@@ -1442,7 +1442,8 @@ static struct clk_lookup mx51_lookups[] = {
 	_REGISTER_CLOCK(NULL, "gpt_32k", gpt_32k_clk)
 	_REGISTER_CLOCK("imx51-ecspi.0", NULL, ecspi1_clk)
 	_REGISTER_CLOCK("imx51-ecspi.1", NULL, ecspi2_clk)
-	_REGISTER_CLOCK("imx51-cspi.0", NULL, cspi_clk)
+	/* i.mx51 has the i.mx35 type cspi */
+	_REGISTER_CLOCK("imx35-cspi.0", NULL, cspi_clk)
 	_REGISTER_CLOCK("sdhci-esdhc-imx.0", NULL, esdhc1_clk)
 	_REGISTER_CLOCK("sdhci-esdhc-imx.1", NULL, esdhc2_clk)
 	_REGISTER_CLOCK("sdhci-esdhc-imx.2", NULL, esdhc3_clk)
@@ -1471,9 +1472,11 @@ static struct clk_lookup mx53_lookups[] = {
 	_REGISTER_CLOCK("sdhci-esdhc-imx.1", NULL, esdhc2_mx53_clk)
 	_REGISTER_CLOCK("sdhci-esdhc-imx.2", NULL, esdhc3_mx53_clk)
 	_REGISTER_CLOCK("sdhci-esdhc-imx.3", NULL, esdhc4_mx53_clk)
-	_REGISTER_CLOCK("imx53-ecspi.0", NULL, ecspi1_clk)
-	_REGISTER_CLOCK("imx53-ecspi.1", NULL, ecspi2_clk)
-	_REGISTER_CLOCK("imx53-cspi.0", NULL, cspi_clk)
+	/* i.mx53 has the i.mx51 type ecspi */
+	_REGISTER_CLOCK("imx51-ecspi.0", NULL, ecspi1_clk)
+	_REGISTER_CLOCK("imx51-ecspi.1", NULL, ecspi2_clk)
+	/* i.mx53 has the i.mx25 type cspi */
+	_REGISTER_CLOCK("imx35-cspi.0", NULL, cspi_clk)
 	_REGISTER_CLOCK("imx2-wdt.0", NULL, dummy_clk)
 	_REGISTER_CLOCK("imx2-wdt.1", NULL, dummy_clk)
 };

arch/arm/mach-s3c2410/include/mach/spi-gpio.h

-/* arch/arm/mach-s3c2410/include/mach/spi-gpio.h
- *
- * Copyright (c) 2006 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 - SPI Controller platform_device info
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_SPIGPIO_H
-#define __ASM_ARCH_SPIGPIO_H __FILE__
-
-struct s3c2410_spigpio_info {
-	unsigned long		 pin_clk;
-	unsigned long		 pin_mosi;
-	unsigned long		 pin_miso;
-
-	int			 num_chipselect;
-	int			 bus_num;
-
-	void (*chip_select)(struct s3c2410_spigpio_info *spi, int cs);
-};
-
-
-#endif /* __ASM_ARCH_SPIGPIO_H */

arch/arm/mach-s3c2410/mach-qt2410.c

@@ -32,7 +32,7 @@
 #include <linux/platform_device.h>
 #include <linux/serial_core.h>
 #include <linux/spi/spi.h>
-#include <linux/spi/spi_bitbang.h>
+#include <linux/spi/spi_gpio.h>
 #include <linux/io.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/nand.h>
@@ -53,8 +53,6 @@
 #include <mach/fb.h>
 #include <plat/nand.h>
 #include <plat/udc.h>
-#include <mach/spi.h>
-#include <mach/spi-gpio.h>
 #include <plat/iic.h>
 
 #include <plat/common-smdk.h>
@@ -216,32 +214,16 @@ static struct platform_device qt2410_led = {
 
 /* SPI */
 
-static void spi_gpio_cs(struct s3c2410_spigpio_info *spi, int cs)
-{
-	switch (cs) {
-	case BITBANG_CS_ACTIVE:
-		gpio_set_value(S3C2410_GPB(5), 0);
-		break;
-	case BITBANG_CS_INACTIVE:
-		gpio_set_value(S3C2410_GPB(5), 1);
-		break;
-	}
-}
-
-static struct s3c2410_spigpio_info spi_gpio_cfg = {
-	.pin_clk	= S3C2410_GPG(7),
-	.pin_mosi	= S3C2410_GPG(6),
-	.pin_miso	= S3C2410_GPG(5),
-	.chip_select	= &spi_gpio_cs,
+static struct spi_gpio_platform_data spi_gpio_cfg = {
+	.sck		= S3C2410_GPG(7),
+	.mosi		= S3C2410_GPG(6),
+	.miso		= S3C2410_GPG(5),
 };
 
-
 static struct platform_device qt2410_spi = {
-	.name		  = "s3c24xx-spi-gpio",
-	.id		  = 1,
-	.dev = {
-		.platform_data = &spi_gpio_cfg,
-	},
+	.name		= "spi-gpio",
+	.id		= 1,
+	.dev.platform_data = &spi_gpio_cfg,
 };
 
 /* Board devices */

arch/arm/mach-s3c2412/mach-jive.c

@@ -25,6 +25,7 @@
 #include <video/ili9320.h>
 
 #include <linux/spi/spi.h>
+#include <linux/spi/spi_gpio.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -38,7 +39,6 @@
 #include <mach/regs-gpio.h>
 #include <mach/regs-mem.h>
 #include <mach/regs-lcd.h>
-#include <mach/spi-gpio.h>
 #include <mach/fb.h>
 
 #include <asm/mach-types.h>
@@ -389,45 +389,30 @@ static struct ili9320_platdata jive_lcm_config = {
 
 /* LCD SPI support */
 
-static void jive_lcd_spi_chipselect(struct s3c2410_spigpio_info *spi, int cs)
-{
-	gpio_set_value(S3C2410_GPB(7), cs ? 0 : 1);
-}
-
-static struct s3c2410_spigpio_info jive_lcd_spi = {
-	.bus_num	= 1,
-	.pin_clk	= S3C2410_GPG(8),
-	.pin_mosi	= S3C2410_GPB(8),
-	.num_chipselect	= 1,
-	.chip_select	= jive_lcd_spi_chipselect,
+static struct spi_gpio_platform_data jive_lcd_spi = {
+	.sck		= S3C2410_GPG(8),
+	.mosi		= S3C2410_GPB(8),
+	.miso		= SPI_GPIO_NO_MISO,
 };
 
 static struct platform_device jive_device_lcdspi = {
-	.name		= "spi_s3c24xx_gpio",
+	.name		= "spi-gpio",
 	.id		= 1,
-	.num_resources  = 0,
 	.dev.platform_data = &jive_lcd_spi,
 };
 
-/* WM8750 audio code SPI definition */
 
-static void jive_wm8750_chipselect(struct s3c2410_spigpio_info *spi, int cs)
-{
-	gpio_set_value(S3C2410_GPH(10), cs ? 0 : 1);
-}
+/* WM8750 audio code SPI definition */
 
-static struct s3c2410_spigpio_info jive_wm8750_spi = {
-	.bus_num	= 2,
-	.pin_clk	= S3C2410_GPB(4),
-	.pin_mosi	= S3C2410_GPB(9),
-	.num_chipselect	= 1,
-	.chip_select	= jive_wm8750_chipselect,
+static struct spi_gpio_platform_data jive_wm8750_spi = {
+	.sck		= S3C2410_GPB(4),
+	.mosi		= S3C2410_GPB(9),
+	.miso		= SPI_GPIO_NO_MISO,
 };
 
 static struct platform_device jive_device_wm8750 = {
-	.name		= "spi_s3c24xx_gpio",
+	.name		= "spi-gpio",
 	.id		= 2,
-	.num_resources  = 0,
 	.dev.platform_data = &jive_wm8750_spi,
 };
 
@@ -441,12 +426,14 @@ static struct spi_board_info __initdata jive_spi_devs[] = {
 		.mode		= SPI_MODE_3,	/* CPOL=1, CPHA=1 */
 		.max_speed_hz	= 100000,
 		.platform_data	= &jive_lcm_config,
+		.controller_data = (void *)S3C2410_GPB(7),
 	}, {
 		.modalias	= "WM8750",
 		.bus_num	= 2,
 		.chip_select	= 0,
 		.mode		= SPI_MODE_0,	/* CPOL=0, CPHA=0 */
 		.max_speed_hz	= 100000,
+		.controller_data = (void *)S3C2410_GPH(10),
 	},
 };
 

arch/arm/mach-s3c2440/mach-gta02.c

@@ -74,7 +74,6 @@
 #include <mach/fb.h>
 
 #include <mach/spi.h>
-#include <mach/spi-gpio.h>
 #include <plat/usb-control.h>
 #include <mach/regs-mem.h>
 #include <mach/hardware.h>

arch/arm/plat-mxc/devices/platform-spi_imx.c

@@ -40,9 +40,10 @@ const struct imx_spi_imx_data imx21_cspi_data[] __initconst = {
 #endif
 
 #ifdef CONFIG_SOC_IMX25
+/* i.mx25 has the i.mx35 type cspi */
 const struct imx_spi_imx_data imx25_cspi_data[] __initconst = {
 #define imx25_cspi_data_entry(_id, _hwid)				\
-	imx_spi_imx_data_entry(MX25, CSPI, "imx25-cspi", _id, _hwid, SZ_16K)
+	imx_spi_imx_data_entry(MX25, CSPI, "imx35-cspi", _id, _hwid, SZ_16K)
 	imx25_cspi_data_entry(0, 1),
 	imx25_cspi_data_entry(1, 2),
 	imx25_cspi_data_entry(2, 3),
@@ -79,8 +80,9 @@ const struct imx_spi_imx_data imx35_cspi_data[] __initconst = {
 #endif /* ifdef CONFIG_SOC_IMX35 */
 
 #ifdef CONFIG_SOC_IMX51
+/* i.mx51 has the i.mx35 type cspi */
 const struct imx_spi_imx_data imx51_cspi_data __initconst =
-	imx_spi_imx_data_entry_single(MX51, CSPI, "imx51-cspi", 2, , SZ_4K);
+	imx_spi_imx_data_entry_single(MX51, CSPI, "imx35-cspi", 2, , SZ_4K);
 
 const struct imx_spi_imx_data imx51_ecspi_data[] __initconst = {
 #define imx51_ecspi_data_entry(_id, _hwid)				\
@@ -91,12 +93,14 @@ const struct imx_spi_imx_data imx51_ecspi_data[] __initconst = {
 #endif /* ifdef CONFIG_SOC_IMX51 */
 
 #ifdef CONFIG_SOC_IMX53
+/* i.mx53 has the i.mx35 type cspi */
 const struct imx_spi_imx_data imx53_cspi_data __initconst =
-	imx_spi_imx_data_entry_single(MX53, CSPI, "imx53-cspi", 0, , SZ_4K);
+	imx_spi_imx_data_entry_single(MX53, CSPI, "imx35-cspi", 0, , SZ_4K);
 
+/* i.mx53 has the i.mx51 type ecspi */
 const struct imx_spi_imx_data imx53_ecspi_data[] __initconst = {
 #define imx53_ecspi_data_entry(_id, _hwid)				\
-	imx_spi_imx_data_entry(MX53, ECSPI, "imx53-ecspi", _id, _hwid, SZ_4K)
+	imx_spi_imx_data_entry(MX53, ECSPI, "imx51-ecspi", _id, _hwid, SZ_4K)
 	imx53_ecspi_data_entry(0, 1),
 	imx53_ecspi_data_entry(1, 2),
 };

drivers/dma/Kconfig

@@ -237,6 +237,13 @@ config MXS_DMA
 	  Support the MXS DMA engine. This engine including APBH-DMA
 	  and APBX-DMA is integrated into Freescale i.MX23/28 chips.
 
+config EP93XX_DMA
+	bool "Cirrus Logic EP93xx DMA support"
+	depends on ARCH_EP93XX
+	select DMA_ENGINE
+	help
+	  Enable support for the Cirrus Logic EP93xx M2P/M2M DMA controller.
+
 config DMA_ENGINE
 	bool
 

drivers/dma/Makefile

@@ -25,3 +25,4 @@ obj-$(CONFIG_STE_DMA40) += ste_dma40.o ste_dma40_ll.o
 obj-$(CONFIG_PL330_DMA) += pl330.o
 obj-$(CONFIG_PCH_DMA) += pch_dma.o
 obj-$(CONFIG_AMBA_PL08X) += amba-pl08x.o
+obj-$(CONFIG_EP93XX_DMA) += ep93xx_dma.o

drivers/spi/Kconfig

@@ -86,9 +86,6 @@ config SPI_BFIN_SPORT
 	help
 	  Enable support for a SPI bus via the Blackfin SPORT peripheral.
 
-	  This driver can also be built as a module.  If so, the module
-	  will be called spi_bfin_sport.
-
 config SPI_AU1550
 	tristate "Au1550/Au12x0 SPI Controller"
 	depends on (SOC_AU1550 || SOC_AU1200) && EXPERIMENTAL
@@ -97,9 +94,6 @@ config SPI_AU1550
 	  If you say yes to this option, support will be included for the
 	  Au1550 SPI controller (may also work with Au1200,Au1210,Au1250).
 
-	  This driver can also be built as a module.  If so, the module
-	  will be called au1550_spi.
-
 config SPI_BITBANG
 	tristate "Utilities for Bitbanging SPI masters"
 	help
@@ -130,9 +124,6 @@ config SPI_COLDFIRE_QSPI
 	  This enables support for the Coldfire QSPI controller in master
 	  mode.
 
-	  This driver can also be built as a module.  If so, the module
-	  will be called coldfire_qspi.
-
 config SPI_DAVINCI
 	tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
 	depends on SPI_MASTER && ARCH_DAVINCI
@@ -140,9 +131,6 @@ config SPI_DAVINCI
 	help
 	  SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
 
-	  This driver can also be built as a module. The module will be called
-	  davinci_spi.
-
 config SPI_EP93XX
 	tristate "Cirrus Logic EP93xx SPI controller"
 	depends on ARCH_EP93XX
@@ -150,9 +138,6 @@ config SPI_EP93XX
 	  This enables using the Cirrus EP93xx SPI controller in master
 	  mode.
 
-	  To compile this driver as a module, choose M here. The module will be
-	  called ep93xx_spi.
-
 config SPI_GPIO
 	tristate "GPIO-based bitbanging SPI Master"
 	depends on GENERIC_GPIO
@@ -169,21 +154,6 @@ config SPI_GPIO
 	  GPIO operations, you should be able to leverage that for better
 	  speed with a custom version of this driver; see the source code.
 
-config SPI_IMX_VER_IMX1
-	def_bool y if SOC_IMX1
-
-config SPI_IMX_VER_0_0
-	def_bool y if SOC_IMX21 || SOC_IMX27
-
-config SPI_IMX_VER_0_4
-	def_bool y if SOC_IMX31
-
-config SPI_IMX_VER_0_7
-	def_bool y if ARCH_MX25 || SOC_IMX35 || SOC_IMX51 || SOC_IMX53
-
-config SPI_IMX_VER_2_3
-	def_bool y if SOC_IMX51 || SOC_IMX53
-
 config SPI_IMX
 	tristate "Freescale i.MX SPI controllers"
 	depends on ARCH_MXC
@@ -328,16 +298,6 @@ config SPI_S3C24XX_FIQ
 	  no free DMA channels, or when doing transfers that required both
 	  TX and RX data paths.
 
-config SPI_S3C24XX_GPIO
-	tristate "Samsung S3C24XX series SPI by GPIO"
-	depends on ARCH_S3C2410 && EXPERIMENTAL
-	select SPI_BITBANG
-	help
-	  SPI driver for Samsung S3C24XX series ARM SoCs using
-	  GPIO lines to provide the SPI bus. This can be used where
-	  the inbuilt hardware cannot provide the transfer mode, or
-	  where the board is using non hardware connected pins.
-
 config SPI_S3C64XX
 	tristate "Samsung S3C64XX series type SPI"
 	depends on (ARCH_S3C64XX || ARCH_S5P64X0)
@@ -385,16 +345,16 @@ config SPI_TI_SSP
 	  This selects an SPI master implementation using a TI sequencer
 	  serial port.
 
-	  To compile this driver as a module, choose M here: the
-	  module will be called ti-ssp-spi.
-
 config SPI_TOPCLIFF_PCH
-	tristate "Topcliff PCH SPI Controller"
+	tristate "Intel EG20T PCH/OKI SEMICONDUCTOR ML7213 IOH SPI controller"
 	depends on PCI
 	help
 	  SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
 	  used in some x86 embedded processors.
 
+	  This driver also supports the ML7213, a companion chip for the
+	  Atom E6xx series and compatible with the Intel EG20T PCH.
+
 config SPI_TXX9
 	tristate "Toshiba TXx9 SPI controller"
 	depends on GENERIC_GPIO && CPU_TX49XX

drivers/spi/Makefile

@@ -7,68 +7,55 @@ ccflags-$(CONFIG_SPI_DEBUG) := -DDEBUG
 # small core, mostly translating board-specific
 # config declarations into driver model code
 obj-$(CONFIG_SPI_MASTER)		+= spi.o
+obj-$(CONFIG_SPI_SPIDEV)		+= spidev.o
 
 # SPI master controller drivers (bus)
-obj-$(CONFIG_SPI_ALTERA)		+= spi_altera.o
-obj-$(CONFIG_SPI_ATMEL)			+= atmel_spi.o
-obj-$(CONFIG_SPI_ATH79)			+= ath79_spi.o
-obj-$(CONFIG_SPI_BFIN)			+= spi_bfin5xx.o
-obj-$(CONFIG_SPI_BFIN_SPORT)		+= spi_bfin_sport.o
-obj-$(CONFIG_SPI_BITBANG)		+= spi_bitbang.o
-obj-$(CONFIG_SPI_AU1550)		+= au1550_spi.o
-obj-$(CONFIG_SPI_BUTTERFLY)		+= spi_butterfly.o
-obj-$(CONFIG_SPI_COLDFIRE_QSPI)		+= coldfire_qspi.o
-obj-$(CONFIG_SPI_DAVINCI)		+= davinci_spi.o
-obj-$(CONFIG_SPI_DESIGNWARE)		+= dw_spi.o
-obj-$(CONFIG_SPI_DW_PCI)		+= dw_spi_midpci.o
-dw_spi_midpci-objs			:= dw_spi_pci.o dw_spi_mid.o
-obj-$(CONFIG_SPI_DW_MMIO)		+= dw_spi_mmio.o
-obj-$(CONFIG_SPI_EP93XX)		+= ep93xx_spi.o
-obj-$(CONFIG_SPI_GPIO)			+= spi_gpio.o
-obj-$(CONFIG_SPI_IMX)			+= spi_imx.o
-obj-$(CONFIG_SPI_LM70_LLP)		+= spi_lm70llp.o
-obj-$(CONFIG_SPI_PXA2XX)		+= pxa2xx_spi.o
-obj-$(CONFIG_SPI_PXA2XX_PCI)		+= pxa2xx_spi_pci.o
-obj-$(CONFIG_SPI_OC_TINY)		+= spi_oc_tiny.o
-obj-$(CONFIG_SPI_OMAP_UWIRE)		+= omap_uwire.o
-obj-$(CONFIG_SPI_OMAP24XX)		+= omap2_mcspi.o
-obj-$(CONFIG_SPI_OMAP_100K)		+= omap_spi_100k.o
-obj-$(CONFIG_SPI_ORION)			+= orion_spi.o
-obj-$(CONFIG_SPI_PL022)			+= amba-pl022.o
-obj-$(CONFIG_SPI_MPC512x_PSC)		+= mpc512x_psc_spi.o
-obj-$(CONFIG_SPI_MPC52xx_PSC)		+= mpc52xx_psc_spi.o
-obj-$(CONFIG_SPI_MPC52xx)		+= mpc52xx_spi.o
-obj-$(CONFIG_SPI_FSL_LIB)		+= spi_fsl_lib.o
-obj-$(CONFIG_SPI_FSL_ESPI)		+= spi_fsl_espi.o
-obj-$(CONFIG_SPI_FSL_SPI)		+= spi_fsl_spi.o
-obj-$(CONFIG_SPI_PPC4xx)		+= spi_ppc4xx.o
-obj-$(CONFIG_SPI_S3C24XX_GPIO)		+= spi_s3c24xx_gpio.o
-obj-$(CONFIG_SPI_S3C24XX)		+= spi_s3c24xx_hw.o
-obj-$(CONFIG_SPI_S3C64XX)		+= spi_s3c64xx.o
-obj-$(CONFIG_SPI_TEGRA)			+= spi_tegra.o
-obj-$(CONFIG_SPI_TI_SSP)		+= ti-ssp-spi.o
-obj-$(CONFIG_SPI_TOPCLIFF_PCH)		+= spi_topcliff_pch.o
-obj-$(CONFIG_SPI_TXX9)			+= spi_txx9.o
-obj-$(CONFIG_SPI_XILINX)		+= xilinx_spi.o
-obj-$(CONFIG_SPI_SH)			+= spi_sh.o
-obj-$(CONFIG_SPI_SH_SCI)		+= spi_sh_sci.o
-obj-$(CONFIG_SPI_SH_MSIOF)		+= spi_sh_msiof.o
-obj-$(CONFIG_SPI_STMP3XXX)		+= spi_stmp.o
-obj-$(CONFIG_SPI_NUC900)		+= spi_nuc900.o
+obj-$(CONFIG_SPI_ALTERA)		+= spi-altera.o
+obj-$(CONFIG_SPI_ATMEL)			+= spi-atmel.o
+obj-$(CONFIG_SPI_ATH79)			+= spi-ath79.o
+obj-$(CONFIG_SPI_AU1550)		+= spi-au1550.o
+obj-$(CONFIG_SPI_BFIN)			+= spi-bfin5xx.o
+obj-$(CONFIG_SPI_BFIN_SPORT)		+= spi-bfin-sport.o
+obj-$(CONFIG_SPI_BITBANG)		+= spi-bitbang.o
+obj-$(CONFIG_SPI_BUTTERFLY)		+= spi-butterfly.o
+obj-$(CONFIG_SPI_COLDFIRE_QSPI)		+= spi-coldfire-qspi.o
+obj-$(CONFIG_SPI_DAVINCI)		+= spi-davinci.o
+obj-$(CONFIG_SPI_DESIGNWARE)		+= spi-dw.o
+obj-$(CONFIG_SPI_DW_MMIO)		+= spi-dw-mmio.o
+obj-$(CONFIG_SPI_DW_PCI)		+= spi-dw-midpci.o
+spi-dw-midpci-objs			:= spi-dw-pci.o spi-dw-mid.o
+obj-$(CONFIG_SPI_EP93XX)		+= spi-ep93xx.o
+obj-$(CONFIG_SPI_FSL_LIB)		+= spi-fsl-lib.o
+obj-$(CONFIG_SPI_FSL_ESPI)		+= spi-fsl-espi.o
+obj-$(CONFIG_SPI_FSL_SPI)		+= spi-fsl-spi.o
+obj-$(CONFIG_SPI_GPIO)			+= spi-gpio.o
+obj-$(CONFIG_SPI_IMX)			+= spi-imx.o
+obj-$(CONFIG_SPI_LM70_LLP)		+= spi-lm70llp.o
+obj-$(CONFIG_SPI_MPC512x_PSC)		+= spi-mpc512x-psc.o
+obj-$(CONFIG_SPI_MPC52xx_PSC)		+= spi-mpc52xx-psc.o
+obj-$(CONFIG_SPI_MPC52xx)		+= spi-mpc52xx.o
+obj-$(CONFIG_SPI_NUC900)		+= spi-nuc900.o
+obj-$(CONFIG_SPI_OC_TINY)		+= spi-oc-tiny.o
+obj-$(CONFIG_SPI_OMAP_UWIRE)		+= spi-omap-uwire.o
+obj-$(CONFIG_SPI_OMAP_100K)		+= spi-omap-100k.o
+obj-$(CONFIG_SPI_OMAP24XX)		+= spi-omap2-mcspi.o
+obj-$(CONFIG_SPI_ORION)			+= spi-orion.o
+obj-$(CONFIG_SPI_PL022)			+= spi-pl022.o
+obj-$(CONFIG_SPI_PPC4xx)		+= spi-ppc4xx.o
+obj-$(CONFIG_SPI_PXA2XX)		+= spi-pxa2xx.o
+obj-$(CONFIG_SPI_PXA2XX_PCI)		+= spi-pxa2xx-pci.o
+obj-$(CONFIG_SPI_S3C24XX)		+= spi-s3c24xx-hw.o
+spi-s3c24xx-hw-y			:= spi-s3c24xx.o
+spi-s3c24xx-hw-$(CONFIG_SPI_S3C24XX_FIQ) += spi-s3c24xx-fiq.o
+obj-$(CONFIG_SPI_S3C64XX)		+= spi-s3c64xx.o
+obj-$(CONFIG_SPI_SH)			+= spi-sh.o
+obj-$(CONFIG_SPI_SH_MSIOF)		+= spi-sh-msiof.o
+obj-$(CONFIG_SPI_SH_SCI)		+= spi-sh-sci.o
+obj-$(CONFIG_SPI_STMP3XXX)		+= spi-stmp.o
+obj-$(CONFIG_SPI_TEGRA)			+= spi-tegra.o
+obj-$(CONFIG_SPI_TI_SSP)		+= spi-ti-ssp.o
+obj-$(CONFIG_SPI_TLE62X0)		+= spi-tle62x0.o
+obj-$(CONFIG_SPI_TOPCLIFF_PCH)		+= spi-topcliff-pch.o
+obj-$(CONFIG_SPI_TXX9)			+= spi-txx9.o
+obj-$(CONFIG_SPI_XILINX)		+= spi-xilinx.o
 
-# special build for s3c24xx spi driver with fiq support
-spi_s3c24xx_hw-y			:= spi_s3c24xx.o
-spi_s3c24xx_hw-$(CONFIG_SPI_S3C24XX_FIQ) += spi_s3c24xx_fiq.o
-
-# 	... add above this line ...
-
-# SPI protocol drivers (device/link on bus)
-obj-$(CONFIG_SPI_SPIDEV)	+= spidev.o
-obj-$(CONFIG_SPI_TLE62X0)	+= tle62x0.o
-# 	... add above this line ...
-
-# SPI slave controller drivers (upstream link)
-# 	... add above this line ...
-
-# SPI slave drivers (protocol for that link)
-# 	... add above this line ...

drivers/spi/atmel_spi.h

-/*
- * Register definitions for Atmel Serial Peripheral Interface (SPI)
- *
- * Copyright (C) 2006 Atmel Corporation
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#ifndef __ATMEL_SPI_H__
-#define __ATMEL_SPI_H__
-
-/* SPI register offsets */
-#define SPI_CR					0x0000
-#define SPI_MR					0x0004
-#define SPI_RDR					0x0008
-#define SPI_TDR					0x000c
-#define SPI_SR					0x0010
-#define SPI_IER					0x0014
-#define SPI_IDR					0x0018
-#define SPI_IMR					0x001c
-#define SPI_CSR0				0x0030
-#define SPI_CSR1				0x0034
-#define SPI_CSR2				0x0038
-#define SPI_CSR3				0x003c
-#define SPI_RPR					0x0100
-#define SPI_RCR					0x0104
-#define SPI_TPR					0x0108
-#define SPI_TCR					0x010c
-#define SPI_RNPR				0x0110
-#define SPI_RNCR				0x0114
-#define SPI_TNPR				0x0118
-#define SPI_TNCR				0x011c
-#define SPI_PTCR				0x0120
-#define SPI_PTSR				0x0124
-
-/* Bitfields in CR */
-#define SPI_SPIEN_OFFSET			0
-#define SPI_SPIEN_SIZE				1
-#define SPI_SPIDIS_OFFSET			1
-#define SPI_SPIDIS_SIZE				1
-#define SPI_SWRST_OFFSET			7
-#define SPI_SWRST_SIZE				1
-#define SPI_LASTXFER_OFFSET			24
-#define SPI_LASTXFER_SIZE			1
-
-/* Bitfields in MR */
-#define SPI_MSTR_OFFSET				0
-#define SPI_MSTR_SIZE				1
-#define SPI_PS_OFFSET				1
-#define SPI_PS_SIZE				1
-#define SPI_PCSDEC_OFFSET			2
-#define SPI_PCSDEC_SIZE				1
-#define SPI_FDIV_OFFSET				3
-#define SPI_FDIV_SIZE				1
-#define SPI_MODFDIS_OFFSET			4
-#define SPI_MODFDIS_SIZE			1
-#define SPI_LLB_OFFSET				7
-#define SPI_LLB_SIZE				1
-#define SPI_PCS_OFFSET				16
-#define SPI_PCS_SIZE				4
-#define SPI_DLYBCS_OFFSET			24
-#define SPI_DLYBCS_SIZE				8
-
-/* Bitfields in RDR */
-#define SPI_RD_OFFSET				0
-#define SPI_RD_SIZE				16
-
-/* Bitfields in TDR */
-#define SPI_TD_OFFSET				0
-#define SPI_TD_SIZE				16
-
-/* Bitfields in SR */
-#define SPI_RDRF_OFFSET				0
-#define SPI_RDRF_SIZE				1
-#define SPI_TDRE_OFFSET				1
-#define SPI_TDRE_SIZE				1
-#define SPI_MODF_OFFSET				2
-#define SPI_MODF_SIZE				1
-#define SPI_OVRES_OFFSET			3
-#define SPI_OVRES_SIZE				1
-#define SPI_ENDRX_OFFSET			4
-#define SPI_ENDRX_SIZE				1
-#define SPI_ENDTX_OFFSET			5
-#define SPI_ENDTX_SIZE				1
-#define SPI_RXBUFF_OFFSET			6
-#define SPI_RXBUFF_SIZE				1
-#define SPI_TXBUFE_OFFSET			7
-#define SPI_TXBUFE_SIZE				1
-#define SPI_NSSR_OFFSET				8
-#define SPI_NSSR_SIZE				1
-#define SPI_TXEMPTY_OFFSET			9
-#define SPI_TXEMPTY_SIZE			1
-#define SPI_SPIENS_OFFSET			16
-#define SPI_SPIENS_SIZE				1
-
-/* Bitfields in CSR0 */
-#define SPI_CPOL_OFFSET				0
-#define SPI_CPOL_SIZE				1
-#define SPI_NCPHA_OFFSET			1
-#define SPI_NCPHA_SIZE				1
-#define SPI_CSAAT_OFFSET			3
-#define SPI_CSAAT_SIZE				1
-#define SPI_BITS_OFFSET				4
-#define SPI_BITS_SIZE				4
-#define SPI_SCBR_OFFSET				8
-#define SPI_SCBR_SIZE				8
-#define SPI_DLYBS_OFFSET			16
-#define SPI_DLYBS_SIZE				8
-#define SPI_DLYBCT_OFFSET			24
-#define SPI_DLYBCT_SIZE				8
-
-/* Bitfields in RCR */
-#define SPI_RXCTR_OFFSET			0
-#define SPI_RXCTR_SIZE				16
-
-/* Bitfields in TCR */
-#define SPI_TXCTR_OFFSET			0
-#define SPI_TXCTR_SIZE				16
-
-/* Bitfields in RNCR */
-#define SPI_RXNCR_OFFSET			0
-#define SPI_RXNCR_SIZE				16
-
-/* Bitfields in TNCR */
-#define SPI_TXNCR_OFFSET			0
-#define SPI_TXNCR_SIZE				16
-
-/* Bitfields in PTCR */
-#define SPI_RXTEN_OFFSET			0
-#define SPI_RXTEN_SIZE				1
-#define SPI_RXTDIS_OFFSET			1
-#define SPI_RXTDIS_SIZE				1
-#define SPI_TXTEN_OFFSET			8
-#define SPI_TXTEN_SIZE				1
-#define SPI_TXTDIS_OFFSET			9
-#define SPI_TXTDIS_SIZE				1
-
-/* Constants for BITS */
-#define SPI_BITS_8_BPT				0
-#define SPI_BITS_9_BPT				1
-#define SPI_BITS_10_BPT				2
-#define SPI_BITS_11_BPT				3
-#define SPI_BITS_12_BPT				4
-#define SPI_BITS_13_BPT				5
-#define SPI_BITS_14_BPT				6
-#define SPI_BITS_15_BPT				7
-#define SPI_BITS_16_BPT				8
-
-/* Bit manipulation macros */
-#define SPI_BIT(name) \
-	(1 << SPI_##name##_OFFSET)
-#define SPI_BF(name,value) \
-	(((value) & ((1 << SPI_##name##_SIZE) - 1)) << SPI_##name##_OFFSET)
-#define SPI_BFEXT(name,value) \
-	(((value) >> SPI_##name##_OFFSET) & ((1 << SPI_##name##_SIZE) - 1))
-#define SPI_BFINS(name,value,old) \
-	( ((old) & ~(((1 << SPI_##name##_SIZE) - 1) << SPI_##name##_OFFSET)) \
-	  | SPI_BF(name,value))
-
-/* Register access macros */
-#define spi_readl(port,reg) \
-	__raw_readl((port)->regs + SPI_##reg)
-#define spi_writel(port,reg,value) \
-	__raw_writel((value), (port)->regs + SPI_##reg)
-
-#endif /* __ATMEL_SPI_H__ */

drivers/spi/ath79_spi.c → drivers/spi/spi-ath79.c

@@ -232,7 +232,7 @@ static __devinit int ath79_spi_probe(struct platform_device *pdev)
 		goto err_put_master;
 	}
 
-	sp->base = ioremap(r->start, r->end - r->start + 1);
+	sp->base = ioremap(r->start, resource_size(r));
 	if (!sp->base) {
 		ret = -ENXIO;
 		goto err_put_master;

drivers/spi/atmel_spi.c → drivers/spi/spi-atmel.c

@@ -25,7 +25,160 @@
 #include <mach/gpio.h>
 #include <mach/cpu.h>
 
-#include "atmel_spi.h"
+/* SPI register offsets */
+#define SPI_CR					0x0000
+#define SPI_MR					0x0004
+#define SPI_RDR					0x0008
+#define SPI_TDR					0x000c
+#define SPI_SR					0x0010
+#define SPI_IER					0x0014
+#define SPI_IDR					0x0018
+#define SPI_IMR					0x001c
+#define SPI_CSR0				0x0030
+#define SPI_CSR1				0x0034
+#define SPI_CSR2				0x0038
+#define SPI_CSR3				0x003c
+#define SPI_RPR					0x0100
+#define SPI_RCR					0x0104
+#define SPI_TPR					0x0108
+#define SPI_TCR					0x010c
+#define SPI_RNPR				0x0110
+#define SPI_RNCR				0x0114
+#define SPI_TNPR				0x0118
+#define SPI_TNCR				0x011c
+#define SPI_PTCR				0x0120
+#define SPI_PTSR				0x0124
+
+/* Bitfields in CR */
+#define SPI_SPIEN_OFFSET			0
+#define SPI_SPIEN_SIZE				1
+#define SPI_SPIDIS_OFFSET			1
+#define SPI_SPIDIS_SIZE				1
+#define SPI_SWRST_OFFSET			7
+#define SPI_SWRST_SIZE				1
+#define SPI_LASTXFER_OFFSET			24
+#define SPI_LASTXFER_SIZE			1
+
+/* Bitfields in MR */
+#define SPI_MSTR_OFFSET				0
+#define SPI_MSTR_SIZE				1
+#define SPI_PS_OFFSET				1
+#define SPI_PS_SIZE				1
+#define SPI_PCSDEC_OFFSET			2
+#define SPI_PCSDEC_SIZE				1
+#define SPI_FDIV_OFFSET				3
+#define SPI_FDIV_SIZE				1
+#define SPI_MODFDIS_OFFSET			4
+#define SPI_MODFDIS_SIZE			1
+#define SPI_LLB_OFFSET				7
+#define SPI_LLB_SIZE				1
+#define SPI_PCS_OFFSET				16
+#define SPI_PCS_SIZE				4
+#define SPI_DLYBCS_OFFSET			24
+#define SPI_DLYBCS_SIZE				8
+
+/* Bitfields in RDR */
+#define SPI_RD_OFFSET				0
+#define SPI_RD_SIZE				16
+
+/* Bitfields in TDR */
+#define SPI_TD_OFFSET				0
+#define SPI_TD_SIZE				16
+
+/* Bitfields in SR */
+#define SPI_RDRF_OFFSET				0
+#define SPI_RDRF_SIZE				1
+#define SPI_TDRE_OFFSET				1
+#define SPI_TDRE_SIZE				1
+#define SPI_MODF_OFFSET				2
+#define SPI_MODF_SIZE				1
+#define SPI_OVRES_OFFSET			3
+#define SPI_OVRES_SIZE				1
+#define SPI_ENDRX_OFFSET			4
+#define SPI_ENDRX_SIZE				1
+#define SPI_ENDTX_OFFSET			5
+#define SPI_ENDTX_SIZE				1
+#define SPI_RXBUFF_OFFSET			6
+#define SPI_RXBUFF_SIZE				1
+#define SPI_TXBUFE_OFFSET			7
+#define SPI_TXBUFE_SIZE				1
+#define SPI_NSSR_OFFSET				8
+#define SPI_NSSR_SIZE				1
+#define SPI_TXEMPTY_OFFSET			9
+#define SPI_TXEMPTY_SIZE			1
+#define SPI_SPIENS_OFFSET			16
+#define SPI_SPIENS_SIZE				1
+
+/* Bitfields in CSR0 */
+#define SPI_CPOL_OFFSET				0
+#define SPI_CPOL_SIZE				1
+#define SPI_NCPHA_OFFSET			1
+#define SPI_NCPHA_SIZE				1
+#define SPI_CSAAT_OFFSET			3
+#define SPI_CSAAT_SIZE				1
+#define SPI_BITS_OFFSET				4
+#define SPI_BITS_SIZE				4
+#define SPI_SCBR_OFFSET				8
+#define SPI_SCBR_SIZE				8
+#define SPI_DLYBS_OFFSET			16
+#define SPI_DLYBS_SIZE				8
+#define SPI_DLYBCT_OFFSET			24
+#define SPI_DLYBCT_SIZE				8
+
+/* Bitfields in RCR */
+#define SPI_RXCTR_OFFSET			0
+#define SPI_RXCTR_SIZE				16
+
+/* Bitfields in TCR */
+#define SPI_TXCTR_OFFSET			0
+#define SPI_TXCTR_SIZE				16
+
+/* Bitfields in RNCR */
+#define SPI_RXNCR_OFFSET			0
+#define SPI_RXNCR_SIZE				16
+
+/* Bitfields in TNCR */
+#define SPI_TXNCR_OFFSET			0
+#define SPI_TXNCR_SIZE				16
+
+/* Bitfields in PTCR */
+#define SPI_RXTEN_OFFSET			0
+#define SPI_RXTEN_SIZE				1
+#define SPI_RXTDIS_OFFSET			1
+#define SPI_RXTDIS_SIZE				1
+#define SPI_TXTEN_OFFSET			8
+#define SPI_TXTEN_SIZE				1
+#define SPI_TXTDIS_OFFSET			9
+#define SPI_TXTDIS_SIZE				1
+
+/* Constants for BITS */
+#define SPI_BITS_8_BPT				0
+#define SPI_BITS_9_BPT				1
+#define SPI_BITS_10_BPT				2
+#define SPI_BITS_11_BPT				3
+#define SPI_BITS_12_BPT				4
+#define SPI_BITS_13_BPT				5
+#define SPI_BITS_14_BPT				6
+#define SPI_BITS_15_BPT				7
+#define SPI_BITS_16_BPT				8
+
+/* Bit manipulation macros */
+#define SPI_BIT(name) \
+	(1 << SPI_##name##_OFFSET)
+#define SPI_BF(name,value) \
+	(((value) & ((1 << SPI_##name##_SIZE) - 1)) << SPI_##name##_OFFSET)
+#define SPI_BFEXT(name,value) \
+	(((value) >> SPI_##name##_OFFSET) & ((1 << SPI_##name##_SIZE) - 1))
+#define SPI_BFINS(name,value,old) \
+	( ((old) & ~(((1 << SPI_##name##_SIZE) - 1) << SPI_##name##_OFFSET)) \
+	  | SPI_BF(name,value))
+
+/* Register access macros */
+#define spi_readl(port,reg) \
+	__raw_readl((port)->regs + SPI_##reg)
+#define spi_writel(port,reg,value) \
+	__raw_writel((value), (port)->regs + SPI_##reg)
+
 
 /*
  * The core SPI transfer engine just talks to a register bank to set up

drivers/spi/au1550_spi.c → drivers/spi/spi-au1550.c

 /*
- * au1550_spi.c - au1550 psc spi controller driver
+ * au1550 psc spi controller driver
  * may work also with au1200, au1210, au1250
  * will not work on au1000, au1100 and au1500 (no full spi controller there)
  *

drivers/spi/spi_bitbang.c → drivers/spi/spi-bitbang.c

 /*
- * spi_bitbang.c - polling/bitbanging SPI master controller driver utilities
+ * polling/bitbanging SPI master controller driver utilities
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
@@ -68,7 +68,7 @@ static unsigned bitbang_txrx_8(
 	unsigned		ns,
 	struct spi_transfer	*t
 ) {
-	unsigned		bits = spi->bits_per_word;
+	unsigned		bits = t->bits_per_word ? : spi->bits_per_word;
 	unsigned		count = t->len;
 	const u8		*tx = t->tx_buf;
 	u8			*rx = t->rx_buf;
@@ -94,7 +94,7 @@ static unsigned bitbang_txrx_16(
 	unsigned		ns,
 	struct spi_transfer	*t
 ) {
-	unsigned		bits = spi->bits_per_word;
+	unsigned		bits = t->bits_per_word ? : spi->bits_per_word;
 	unsigned		count = t->len;
 	const u16		*tx = t->tx_buf;
 	u16			*rx = t->rx_buf;
@@ -120,7 +120,7 @@ static unsigned bitbang_txrx_32(
 	unsigned		ns,
 	struct spi_transfer	*t
 ) {
-	unsigned		bits = spi->bits_per_word;
+	unsigned		bits = t->bits_per_word ? : spi->bits_per_word;
 	unsigned		count = t->len;
 	const u32		*tx = t->tx_buf;
 	u32			*rx = t->rx_buf;

drivers/spi/spi_butterfly.c → drivers/spi/spi-butterfly.c

 /*
- * spi_butterfly.c - parport-to-butterfly adapter
+ * parport-to-butterfly adapter
  *
  * Copyright (C) 2005 David Brownell
  *
@@ -149,7 +149,7 @@ static void butterfly_chipselect(struct spi_device *spi, int value)
 #define	spidelay(X)	do{}while(0)
 //#define	spidelay	ndelay
 
-#include "spi_bitbang_txrx.h"
+#include "spi-bitbang-txrx.h"
 
 static u32
 butterfly_txrx_word_mode0(struct spi_device *spi,

drivers/spi/dw_spi_mid.c → drivers/spi/spi-dw-mid.c

 /*
- * dw_spi_mid.c - special handling for DW core on Intel MID platform
+ * Special handling for DW core on Intel MID platform
  *
  * Copyright (c) 2009, Intel Corporation.
  *
@@ -23,7 +23,7 @@
 #include <linux/slab.h>
 #include <linux/spi/spi.h>
 
-#include "dw_spi.h"
+#include "spi-dw.h"
 
 #ifdef CONFIG_SPI_DW_MID_DMA
 #include <linux/intel_mid_dma.h>

drivers/spi/dw_spi_mmio.c → drivers/spi/spi-dw-mmio.c

 /*
- * dw_spi_mmio.c - Memory-mapped interface driver for DW SPI Core
+ * Memory-mapped interface driver for DW SPI Core
  *
  * Copyright (c) 2010, Octasic semiconductor.
  *
@@ -16,7 +16,7 @@
 #include <linux/spi/spi.h>
 #include <linux/scatterlist.h>
 
-#include "dw_spi.h"
+#include "spi-dw.h"
 
 #define DRIVER_NAME "dw_spi_mmio"
 

drivers/spi/dw_spi_pci.c → drivers/spi/spi-dw-pci.c

 /*
- * dw_spi_pci.c - PCI interface driver for DW SPI Core
+ * PCI interface driver for DW SPI Core
  *
  * Copyright (c) 2009, Intel Corporation.
  *
@@ -22,7 +22,7 @@
 #include <linux/slab.h>
 #include <linux/spi/spi.h>
 
-#include "dw_spi.h"
+#include "spi-dw.h"
 
 #define DRIVER_NAME "dw_spi_pci"
 

drivers/spi/dw_spi.c → drivers/spi/spi-dw.c

 /*
- * dw_spi.c - Designware SPI core controller driver (refer pxa2xx_spi.c)
+ * Designware SPI core controller driver (refer pxa2xx_spi.c)
  *
  * Copyright (c) 2009, Intel Corporation.
  *
@@ -24,7 +24,7 @@
 #include <linux/slab.h>
 #include <linux/spi/spi.h>
 
-#include "dw_spi.h"
+#include "spi-dw.h"
 
 #ifdef CONFIG_DEBUG_FS
 #include <linux/debugfs.h>
@@ -818,9 +818,11 @@ int __devinit dw_spi_add_host(struct dw_spi *dws)
 	dws->prev_chip = NULL;
 	dws->dma_inited = 0;
 	dws->dma_addr = (dma_addr_t)(dws->paddr + 0x60);
+	snprintf(dws->name, sizeof(dws->name), "dw_spi%d",
+			dws->bus_num);
 
 	ret = request_irq(dws->irq, dw_spi_irq, IRQF_SHARED,
-			"dw_spi", dws);
+			dws->name, dws);
 	if (ret < 0) {
 		dev_err(&master->dev, "can not get IRQ\n");
 		goto err_free_master;

drivers/spi/dw_spi.h → drivers/spi/spi-dw.h

@@ -96,6 +96,7 @@ struct dw_spi {
 	struct spi_device	*cur_dev;
 	struct device		*parent_dev;
 	enum dw_ssi_type	type;
+	char			name[16];
 
 	void __iomem		*regs;
 	unsigned long		paddr;

drivers/spi/spi_fsl_espi.c → drivers/spi/spi-fsl-espi.c

@@ -22,7 +22,7 @@
 #include <linux/err.h>
 #include <sysdev/fsl_soc.h>
 
-#include "spi_fsl_lib.h"
+#include "spi-fsl-lib.h"
 
 /* eSPI Controller registers */
 struct fsl_espi_reg {

drivers/spi/spi_fsl_lib.c → drivers/spi/spi-fsl-lib.c

@@ -25,7 +25,7 @@
 #include <linux/of_spi.h>
 #include <sysdev/fsl_soc.h>
 
-#include "spi_fsl_lib.h"
+#include "spi-fsl-lib.h"
 
 #define MPC8XXX_SPI_RX_BUF(type) 					  \
 void mpc8xxx_spi_rx_buf_##type(u32 data, struct mpc8xxx_spi *mpc8xxx_spi) \

drivers/spi/spi_fsl_spi.c → drivers/spi/spi-fsl-spi.c

@@ -37,7 +37,7 @@
 #include <asm/cpm.h>
 #include <asm/qe.h>
 
-#include "spi_fsl_lib.h"
+#include "spi-fsl-lib.h"
 
 /* CPM1 and CPM2 are mutually exclusive. */
 #ifdef CONFIG_CPM1
@@ -684,7 +684,7 @@ static unsigned long fsl_spi_cpm_get_pram(struct mpc8xxx_spi *mspi)
 	struct device_node *np = dev->of_node;
 	const u32 *iprop;
 	int size;
-	unsigned long spi_base_ofs;
+	void __iomem *spi_base;
 	unsigned long pram_ofs = -ENOMEM;
 
 	/* Can't use of_address_to_resource(), QE muram isn't at 0. */
@@ -702,33 +702,27 @@ static unsigned long fsl_spi_cpm_get_pram(struct mpc8xxx_spi *mspi)
 		return pram_ofs;
 	}
 
-	/* CPM1 and CPM2 pram must be at a fixed addr. */
-	if (!iprop || size != sizeof(*iprop) * 4)
-		return -ENOMEM;
-
-	spi_base_ofs = cpm_muram_alloc_fixed(iprop[2], 2);
-	if (IS_ERR_VALUE(spi_base_ofs))
-		return -ENOMEM;
+	spi_base = of_iomap(np, 1);
+	if (spi_base == NULL)
+		return -EINVAL;
 
 	if (mspi->flags & SPI_CPM2) {
 		pram_ofs = cpm_muram_alloc(SPI_PRAM_SIZE, 64);
-		if (!IS_ERR_VALUE(pram_ofs)) {
-			u16 __iomem *spi_base = cpm_muram_addr(spi_base_ofs);
-
-			out_be16(spi_base, pram_ofs);
-		}
+		out_be16(spi_base, pram_ofs);
 	} else {
-		struct spi_pram __iomem *pram = cpm_muram_addr(spi_base_ofs);
+		struct spi_pram __iomem *pram = spi_base;
 		u16 rpbase = in_be16(&pram->rpbase);
 
 		/* Microcode relocation patch applied? */
 		if (rpbase)
 			pram_ofs = rpbase;
-		else
-			return spi_base_ofs;
+		else {
+			pram_ofs = cpm_muram_alloc(SPI_PRAM_SIZE, 64);
+			out_be16(spi_base, pram_ofs);
+		}
 	}
 
-	cpm_muram_free(spi_base_ofs);
+	iounmap(spi_base);
 	return pram_ofs;
 }
 

drivers/spi/spi_gpio.c → drivers/spi/spi-gpio.c

 /*
- * spi_gpio.c - SPI master driver using generic bitbanged GPIO
+ * SPI master driver using generic bitbanged GPIO
  *
  * Copyright (C) 2006,2008 David Brownell
  *
@@ -69,7 +69,7 @@ struct spi_gpio {
  *		#define	SPI_MOSI_GPIO	120
  *		#define	SPI_SCK_GPIO	121
  *		#define	SPI_N_CHIPSEL	4
- *		#include "spi_gpio.c"
+ *		#include "spi-gpio.c"
  */
 
 #ifndef DRIVER_NAME
@@ -127,7 +127,7 @@ static inline int getmiso(const struct spi_device *spi)
  */
 #define spidelay(nsecs)	do {} while (0)
 
-#include "spi_bitbang_txrx.h"
+#include "spi-bitbang-txrx.h"
 
 /*
  * These functions can leverage inline expansion of GPIO calls to shrink

drivers/spi/spi_lm70llp.c → drivers/spi/spi-lm70llp.c

 /*
- * spi_lm70llp.c - driver for LM70EVAL-LLP board for the LM70 sensor
+ * Driver for LM70EVAL-LLP board for the LM70 sensor
  *
  * Copyright (C) 2006 Kaiwan N Billimoria <kaiwan@designergraphix.com>
  *
@@ -174,7 +174,7 @@ static inline int getmiso(struct spi_device *s)
 }
 /*--------------------------------------------------------------------*/
 
-#include "spi_bitbang_txrx.h"
+#include "spi-bitbang-txrx.h"
 
 static void lm70_chipselect(struct spi_device *spi, int value)
 {

drivers/spi/spi_nuc900.c → drivers/spi/spi-nuc900.c

-/* linux/drivers/spi/spi_nuc900.c
- *
+/*
  * Copyright (c) 2009 Nuvoton technology.
  * Wan ZongShun <mcuos.com@gmail.com>
  *
@@ -7,7 +6,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  *
-*/
+ */
 
 #include <linux/init.h>
 #include <linux/spinlock.h>

drivers/spi/omap_uwire.c → drivers/spi/spi-omap-uwire.c

 /*
- * omap_uwire.c -- MicroWire interface driver for OMAP
+ * MicroWire interface driver for OMAP
  *
  * Copyright 2003 MontaVista Software Inc. <source@mvista.com>
  *

drivers/spi/omap2_mcspi.c → drivers/spi/spi-omap2-mcspi.c

@@ -1116,8 +1116,8 @@ static int __init omap2_mcspi_probe(struct platform_device *pdev)
 		status = -ENODEV;
 		goto err1;
 	}
-	if (!request_mem_region(r->start, (r->end - r->start) + 1,
-			dev_name(&pdev->dev))) {
+	if (!request_mem_region(r->start, resource_size(r),
+				dev_name(&pdev->dev))) {
 		status = -EBUSY;
 		goto err1;
 	}
@@ -1125,7 +1125,7 @@ static int __init omap2_mcspi_probe(struct platform_device *pdev)
 	r->start += pdata->regs_offset;
 	r->end += pdata->regs_offset;
 	mcspi->phys = r->start;
-	mcspi->base = ioremap(r->start, r->end - r->start + 1);
+	mcspi->base = ioremap(r->start, resource_size(r));
 	if (!mcspi->base) {
 		dev_dbg(&pdev->dev, "can't ioremap MCSPI\n");
 		status = -ENOMEM;
@@ -1190,7 +1190,7 @@ static int __init omap2_mcspi_probe(struct platform_device *pdev)
 err3:
 	kfree(mcspi->dma_channels);
 err2:
-	release_mem_region(r->start, (r->end - r->start) + 1);
+	release_mem_region(r->start, resource_size(r));
 	iounmap(mcspi->base);
 err1:
 	return status;
@@ -1210,7 +1210,7 @@ static int __exit omap2_mcspi_remove(struct platform_device *pdev)
 
 	omap2_mcspi_disable_clocks(mcspi);
 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	release_mem_region(r->start, (r->end - r->start) + 1);
+	release_mem_region(r->start, resource_size(r));
 
 	base = mcspi->base;
 	spi_unregister_master(master);

drivers/spi/spi_ppc4xx.c → drivers/spi/spi-ppc4xx.c

@@ -502,7 +502,7 @@ static int __init spi_ppc4xx_of_probe(struct platform_device *op)
 		goto free_gpios;
 	}
 	hw->mapbase = resource.start;
-	hw->mapsize = resource.end - resource.start + 1;
+	hw->mapsize = resource_size(&resource);
 
 	/* Sanity check */
 	if (hw->mapsize < sizeof(struct spi_ppc4xx_regs)) {

drivers/spi/spi_s3c24xx_fiq.S → drivers/spi/spi-s3c24xx-fiq.S

@@ -17,7 +17,7 @@
 #include <mach/regs-irq.h>
 #include <plat/regs-spi.h>
 
-#include "spi_s3c24xx_fiq.h"
+#include "spi-s3c24xx-fiq.h"
 
 	.text
 

drivers/spi/spi_s3c64xx.c → drivers/spi/spi-s3c64xx.c

-/* linux/drivers/spi/spi_s3c64xx.c
- *
+/*
  * Copyright (C) 2009 Samsung Electronics Ltd.
  *	Jaswinder Singh <jassi.brar@samsung.com>
  *

drivers/spi/tle62x0.c → drivers/spi/spi-tle62x0.c

 /*
- * tle62x0.c -- support Infineon TLE62x0 driver chips
+ * Support Infineon TLE62x0 driver chips
  *
  * Copyright (c) 2007 Simtec Electronics
  *	Ben Dooks, <ben@simtec.co.uk>