Merge series "spi: sh-msiof: Advertize bit rate limits and actual speed" from...

Merge series "spi: sh-msiof: Advertize bit rate limits and actual speed" from Geert Uytterhoeven <geert+renesas@glider.be>:

	Hi Mark,

This patch series makes the Renesas MSIOF SPI driver fill in actual
transfer speeds and controller limits, so the SPI core can take them
into account.

This has been tested on R-Car Gen2 and Gen3.
Thanks!

Geert Uytterhoeven (2):
  spi: sh-msiof: Fill in spi_transfer.effective_speed_hz
  spi: sh-msiof: Fill in controller speed limits

 drivers/spi/spi-sh-msiof.c | 14 +++++++++++---
 1 file changed, 11 insertions(+), 3 deletions(-)

--
2.25.1

Gr{oetje,eeting}s,

						Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
							    -- Linus Torvalds

drivers/spi/spi-sh-msiof.c

@@ -259,11 +259,13 @@ static const u32 sh_msiof_spi_div_array[] = {
 };
 
 static void sh_msiof_spi_set_clk_regs(struct sh_msiof_spi_priv *p,
-				      unsigned long parent_rate, u32 spi_hz)
+				      struct spi_transfer *t)
 {
+	unsigned long parent_rate = clk_get_rate(p->clk);
+	unsigned int div_pow = p->min_div_pow;
+	u32 spi_hz = t->speed_hz;
 	unsigned long div;
 	u32 brps, scr;
-	unsigned int div_pow = p->min_div_pow;
 
 	if (!spi_hz || !parent_rate) {
 		WARN(1, "Invalid clock rate parameters %lu and %u\n",
@@ -292,6 +294,8 @@ static void sh_msiof_spi_set_clk_regs(struct sh_msiof_spi_priv *p,
 		brps = 32;
 	}
 
+	t->effective_speed_hz = parent_rate / (brps << div_pow);
+
 	scr = sh_msiof_spi_div_array[div_pow] | SISCR_BRPS(brps);
 	sh_msiof_write(p, SITSCR, scr);
 	if (!(p->ctlr->flags & SPI_CONTROLLER_MUST_TX))
@@ -923,7 +927,7 @@ static int sh_msiof_transfer_one(struct spi_controller *ctlr,
 
 	/* setup clocks (clock already enabled in chipselect()) */
 	if (!spi_controller_is_slave(p->ctlr))
-		sh_msiof_spi_set_clk_regs(p, clk_get_rate(p->clk), t->speed_hz);
+		sh_msiof_spi_set_clk_regs(p, t);
 
 	while (ctlr->dma_tx && len > 15) {
 		/*
@@ -1258,6 +1262,7 @@ static int sh_msiof_spi_probe(struct platform_device *pdev)
 	const struct sh_msiof_chipdata *chipdata;
 	struct sh_msiof_spi_info *info;
 	struct sh_msiof_spi_priv *p;
+	unsigned long clksrc;
 	int i;
 	int ret;
 
@@ -1333,6 +1338,9 @@ static int sh_msiof_spi_probe(struct platform_device *pdev)
 	/* init controller code */
 	ctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
 	ctlr->mode_bits |= SPI_LSB_FIRST | SPI_3WIRE;
+	clksrc = clk_get_rate(p->clk);
+	ctlr->min_speed_hz = DIV_ROUND_UP(clksrc, 1024);
+	ctlr->max_speed_hz = DIV_ROUND_UP(clksrc, 1 << p->min_div_pow);
 	ctlr->flags = chipdata->ctlr_flags;
 	ctlr->bus_num = pdev->id;
 	ctlr->num_chipselect = p->info->num_chipselect;