staging: dwc2: reorder some kernel doc comments and struct members

Reorder the kernel doc comments for 'struct dwc2_core_params' to
match the ordering in the struct itself. Reorder the members of
'struct dwc2_qh' (and its kerneldoc comments) to minimize the
amount of structure padding.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/dwc2/core.h

@@ -74,6 +74,9 @@ enum dwc2_lx_state {
  *                       0 - HNP and SRP capable (default)
  *                       1 - SRP Only capable
  *                       2 - No HNP/SRP capable
+ * @otg_ver:            OTG version supported
+ *                       0 - 1.3
+ *                       1 - 2.0
  * @dma_enable:         Specifies whether to use slave or DMA mode for accessing
  *                      the data FIFOs. The driver will automatically detect the
  *                      value for this parameter if none is specified.
@@ -90,20 +93,10 @@ enum dwc2_lx_state {
  *                      the attached device and the value of phy_type.
  *                       0 - High Speed (default)
  *                       1 - Full Speed
- * @host_support_fs_ls_low_power: Specifies whether low power mode is supported
- *                      when attached to a Full Speed or Low Speed device in
- *                      host mode.
- *                       0 - Don't support low power mode (default)
- *                       1 - Support low power mode
- * @host_ls_low_power_phy_clk: Specifies the PHY clock rate in low power mode
- *                      when connected to a Low Speed device in host mode. This
- *                      parameter is applicable only if
- *                      host_support_fs_ls_low_power is enabled. If phy_type is
- *                      set to FS then defaults to 6 MHZ otherwise 48 MHZ.
- *                       0 - 48 MHz
- *                       1 - 6 MHz
  * @enable_dynamic_fifo: 0 - Use coreConsultant-specified FIFO size parameters
  *                       1 - Allow dynamic FIFO sizing (default)
+ * @en_multiple_tx_fifo: Specifies whether dedicated per-endpoint transmit FIFOs
+ *                      are enabled
  * @host_rx_fifo_size:  Number of 4-byte words in the Rx FIFO in host mode when
  *                      dynamic FIFO sizing is enabled
  *                       16 to 32768 (default 1024)
@@ -145,9 +138,19 @@ enum dwc2_lx_state {
  *                       0 - No (default)
  *                       1 - Yes
  * @ulpi_fs_ls:         True to make ULPI phy operate in FS/LS mode only
+ * @host_support_fs_ls_low_power: Specifies whether low power mode is supported
+ *                      when attached to a Full Speed or Low Speed device in
+ *                      host mode.
+ *                       0 - Don't support low power mode (default)
+ *                       1 - Support low power mode
+ * @host_ls_low_power_phy_clk: Specifies the PHY clock rate in low power mode
+ *                      when connected to a Low Speed device in host mode. This
+ *                      parameter is applicable only if
+ *                      host_support_fs_ls_low_power is enabled. If phy_type is
+ *                      set to FS then defaults to 6 MHZ otherwise 48 MHZ.
+ *                       0 - 48 MHz
+ *                       1 - 6 MHz
  * @ts_dline:           True to enable Term Select Dline pulsing
- * @en_multiple_tx_fifo: Specifies whether dedicated per-endpoint transmit FIFOs
- *                      are enabled
  * @reload_ctl:         True to allow dynamic reloading of HFIR register during
  *                      runtime
  * @ahbcfg:             This field allows the default value of the GAHBCFG
@@ -155,9 +158,6 @@ enum dwc2_lx_state {
  *                       -1         - GAHBCFG value will not be overridden
  *                       all others - GAHBCFG value will be overridden with
  *                                    this value
- * @otg_ver:            OTG version supported
- *                       0 - 1.3
- *                       1 - 2.0
  *
  * The following parameters may be specified when starting the module. These
  * parameters define how the DWC_otg controller should be configured.

drivers/staging/dwc2/hcd.h

@@ -232,16 +232,19 @@ enum dwc2_transaction_type {
  *                       - DWC2_HC_PID_DATA1
  * @ping_state:         Ping state
  * @do_split:           Full/low speed endpoint on high-speed hub requires split
- * @qtd_list:           List of QTDs for this QH
- * @channel:            Host channel currently processing transfers for this QH
+ * @td_first:           Index of first activated isochronous transfer descriptor
+ * @td_last:            Index of last activated isochronous transfer descriptor
  * @usecs:              Bandwidth in microseconds per (micro)frame
  * @interval:           Interval between transfers in (micro)frames
- * @sched_frame:        (micro)frame to initialize a periodic transfer.
+ * @sched_frame:        (Micro)frame to initialize a periodic transfer.
  *                      The transfer executes in the following (micro)frame.
  * @start_split_frame:  (Micro)frame at which last start split was initialized
+ * @ntd:                Actual number of transfer descriptors in a list
  * @dw_align_buf:       Used instead of original buffer if its physical address
  *                      is not dword-aligned
  * @dw_align_buf_dma:   DMA address for align_buf
+ * @qtd_list:           List of QTDs for this QH
+ * @channel:            Host channel currently processing transfers for this QH
  * @qh_list_entry:      Entry for QH in either the periodic or non-periodic
  *                      schedule
  * @desc_list:          List of transfer descriptors
@@ -249,9 +252,6 @@ enum dwc2_transaction_type {
  * @n_bytes:            Xfer Bytes array. Each element corresponds to a transfer
  *                      descriptor and indicates original XferSize value for the
  *                      descriptor
- * @ntd:                Actual number of transfer descriptors in a list
- * @td_first:           Index of first activated isochronous transfer descriptor
- * @td_last:            Index of last activated isochronous transfer descriptor
  * @tt_buffer_dirty     True if clear_tt_buffer_complete is pending
  *
  * A Queue Head (QH) holds the static characteristics of an endpoint and
@@ -266,21 +266,21 @@ struct dwc2_qh {
 	u8 data_toggle;
 	u8 ping_state;
 	u8 do_split;
-	struct list_head qtd_list;
-	struct dwc2_host_chan *channel;
+	u8 td_first;
+	u8 td_last;
 	u16 usecs;
 	u16 interval;
 	u16 sched_frame;
 	u16 start_split_frame;
+	u16 ntd;
 	u8 *dw_align_buf;
 	dma_addr_t dw_align_buf_dma;
+	struct list_head qtd_list;
+	struct dwc2_host_chan *channel;
 	struct list_head qh_list_entry;
 	struct dwc2_hcd_dma_desc *desc_list;
 	dma_addr_t desc_list_dma;
 	u32 *n_bytes;
-	u16 ntd;
-	u8 td_first;
-	u8 td_last;
 	unsigned tt_buffer_dirty:1;
 };