Commit 73547406 authored by Linus Walleij's avatar Linus Walleij

gpio: random documentation update

Updated and proofread the documentation for GPIO drivers a bit
when looking over the changes for generic configuration.
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
parent 3d84fdb3
......@@ -41,34 +41,71 @@ In the gpiolib framework each GPIO controller is packaged as a "struct
gpio_chip" (see linux/gpio/driver.h for its complete definition) with members
common to each controller of that type:
- methods to establish GPIO direction
- methods used to access GPIO values
- method to return the IRQ number associated to a given GPIO
- methods to establish GPIO line direction
- methods used to access GPIO line values
- method to set electrical configuration to a a given GPIO line
- method to return the IRQ number associated to a given GPIO line
- flag saying whether calls to its methods may sleep
- optional line names array to identify lines
- optional debugfs dump method (showing extra state like pullup config)
- optional base number (will be automatically assigned if omitted)
- label for diagnostics and GPIOs mapping using platform data
- optional label for diagnostics and GPIO chip mapping using platform data
The code implementing a gpio_chip should support multiple instances of the
controller, possibly using the driver model. That code will configure each
gpio_chip and issue gpiochip_add(). Removing a GPIO controller should be rare;
use gpiochip_remove() when it is unavoidable.
gpio_chip and issue gpiochip_add[_data]() or devm_gpiochip_add_data().
Removing a GPIO controller should be rare; use [devm_]gpiochip_remove() when
it is unavoidable.
Most often a gpio_chip is part of an instance-specific structure with state not
Often a gpio_chip is part of an instance-specific structure with states not
exposed by the GPIO interfaces, such as addressing, power management, and more.
Chips such as codecs will have complex non-GPIO state.
Chips such as audio codecs will have complex non-GPIO states.
Any debugfs dump method should normally ignore signals which haven't been
requested as GPIOs. They can use gpiochip_is_requested(), which returns either
NULL or the label associated with that GPIO when it was requested.
RT_FULL: GPIO driver should not use spinlock_t or any sleepable APIs
RT_FULL: the GPIO driver should not use spinlock_t or any sleepable APIs
(like PM runtime) in its gpio_chip implementation (.get/.set and direction
control callbacks) if it is expected to call GPIO APIs from atomic context
on -RT (inside hard IRQ handlers and similar contexts). Normally this should
not be required.
GPIO electrical configuration
-----------------------------
GPIOs can be configured for several electrical modes of operation by using the
.set_config() callback. Currently this API supports setting debouncing and
single-ended modes (open drain/open source). These settings are described
below.
The .set_config() callback uses the same enumerators and configuration
semantics as the generic pin control drivers. This is not a coincidence: it is
possible to assign the .set_config() to the function gpiochip_generic_config()
which will result in pinctrl_gpio_set_config() being called and eventually
ending up in the pin control back-end "behind" the GPIO controller, usually
closer to the actual pins. This way the pin controller can manage the below
listed GPIO configurations.
GPIOs with debounce support
---------------------------
Debouncing is a configuration set to a pin indicating that it is connected to
a mechanical switch or button, or similar that may bounce. Bouncing means the
line is pulled high/low quickly at very short intervals for mechanical
reasons. This can result in the value being unstable or irqs fireing repeatedly
unless the line is debounced.
Debouncing in practice involves setting up a timer when something happens on
the line, wait a little while and then sample the line again, so see if it
still has the same value (low or high). This could also be repeated by a clever
state machine, waiting for a line to become stable. In either case, it sets
a certain number of milliseconds for debouncing, or just "on/off" if that time
is not configurable.
GPIOs with open drain/source support
------------------------------------
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment