Commit 74791a2d authored by Nicolas Ferre's avatar Nicolas Ferre Committed by Linus Torvalds

mmc: atmel-mci: new MCI2 module support in atmel-mci driver

This new revision of the IP adds some improvements to the MCI already
present in several Atmel SOC.

Some new registers are added and a particular way of handling DMA
interaction lead to a new sequence in function call which is backward
compatible: On MCI2, we must set the DMAEN bit to enable the DMA
handshaking interface.  This must happen before the data transfer command
is sent.

A new function is able to differentiate MCI2 code and is based on
knowledge of processor id (cpu_is_xxx()).
Signed-off-by: default avatarNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: default avatarHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
parent 2635d1ba
......@@ -94,6 +94,7 @@ struct atmel_mci_dma {
* @need_clock_update: Update the clock rate before the next request.
* @need_reset: Reset controller before next request.
* @mode_reg: Value of the MR register.
* @cfg_reg: Value of the CFG register.
* @bus_hz: The rate of @mck in Hz. This forms the basis for MMC bus
* rate and timeout calculations.
* @mapbase: Physical address of the MMIO registers.
......@@ -157,6 +158,7 @@ struct atmel_mci {
bool need_clock_update;
bool need_reset;
u32 mode_reg;
u32 cfg_reg;
unsigned long bus_hz;
unsigned long mapbase;
struct clk *mck;
......@@ -224,6 +226,19 @@ static bool mci_has_rwproof(void)
return true;
}
/*
* The new MCI2 module isn't 100% compatible with the old MCI module,
* and it has a few nice features which we want to use...
*/
static inline bool atmci_is_mci2(void)
{
if (cpu_is_at91sam9g45())
return true;
return false;
}
/*
* The debugfs stuff below is mostly optimized away when
* CONFIG_DEBUG_FS is not set.
......@@ -359,12 +374,33 @@ static int atmci_regs_show(struct seq_file *s, void *v)
buf[MCI_BLKR / 4],
buf[MCI_BLKR / 4] & 0xffff,
(buf[MCI_BLKR / 4] >> 16) & 0xffff);
if (atmci_is_mci2())
seq_printf(s, "CSTOR:\t0x%08x\n", buf[MCI_CSTOR / 4]);
/* Don't read RSPR and RDR; it will consume the data there */
atmci_show_status_reg(s, "SR", buf[MCI_SR / 4]);
atmci_show_status_reg(s, "IMR", buf[MCI_IMR / 4]);
if (atmci_is_mci2()) {
u32 val;
val = buf[MCI_DMA / 4];
seq_printf(s, "DMA:\t0x%08x OFFSET=%u CHKSIZE=%u%s\n",
val, val & 3,
((val >> 4) & 3) ?
1 << (((val >> 4) & 3) + 1) : 1,
val & MCI_DMAEN ? " DMAEN" : "");
val = buf[MCI_CFG / 4];
seq_printf(s, "CFG:\t0x%08x%s%s%s%s\n",
val,
val & MCI_CFG_FIFOMODE_1DATA ? " FIFOMODE_ONE_DATA" : "",
val & MCI_CFG_FERRCTRL_COR ? " FERRCTRL_CLEAR_ON_READ" : "",
val & MCI_CFG_HSMODE ? " HSMODE" : "",
val & MCI_CFG_LSYNC ? " LSYNC" : "");
}
kfree(buf);
return 0;
......@@ -559,6 +595,10 @@ static void atmci_dma_complete(void *arg)
dev_vdbg(&host->pdev->dev, "DMA complete\n");
if (atmci_is_mci2())
/* Disable DMA hardware handshaking on MCI */
mci_writel(host, DMA, mci_readl(host, DMA) & ~MCI_DMAEN);
atmci_dma_cleanup(host);
/*
......@@ -594,7 +634,7 @@ static void atmci_dma_complete(void *arg)
}
static int
atmci_submit_data_dma(struct atmel_mci *host, struct mmc_data *data)
atmci_prepare_data_dma(struct atmel_mci *host, struct mmc_data *data)
{
struct dma_chan *chan;
struct dma_async_tx_descriptor *desc;
......@@ -626,6 +666,9 @@ atmci_submit_data_dma(struct atmel_mci *host, struct mmc_data *data)
if (!chan)
return -ENODEV;
if (atmci_is_mci2())
mci_writel(host, DMA, MCI_DMA_CHKSIZE(3) | MCI_DMAEN);
if (data->flags & MMC_DATA_READ)
direction = DMA_FROM_DEVICE;
else
......@@ -643,10 +686,6 @@ atmci_submit_data_dma(struct atmel_mci *host, struct mmc_data *data)
host->dma.data_desc = desc;
desc->callback = atmci_dma_complete;
desc->callback_param = host;
desc->tx_submit(desc);
/* Go! */
chan->device->device_issue_pending(chan);
return 0;
unmap_exit:
......@@ -654,13 +693,26 @@ atmci_submit_data_dma(struct atmel_mci *host, struct mmc_data *data)
return -ENOMEM;
}
static void atmci_submit_data(struct atmel_mci *host)
{
struct dma_chan *chan = host->data_chan;
struct dma_async_tx_descriptor *desc = host->dma.data_desc;
if (chan) {
desc->tx_submit(desc);
chan->device->device_issue_pending(chan);
}
}
#else /* CONFIG_MMC_ATMELMCI_DMA */
static int atmci_submit_data_dma(struct atmel_mci *host, struct mmc_data *data)
static int atmci_prepare_data_dma(struct atmel_mci *host, struct mmc_data *data)
{
return -ENOSYS;
}
static void atmci_submit_data(struct atmel_mci *host) {}
static void atmci_stop_dma(struct atmel_mci *host)
{
/* Data transfer was stopped by the interrupt handler */
......@@ -674,7 +726,7 @@ static void atmci_stop_dma(struct atmel_mci *host)
* Returns a mask of interrupt flags to be enabled after the whole
* request has been prepared.
*/
static u32 atmci_submit_data(struct atmel_mci *host, struct mmc_data *data)
static u32 atmci_prepare_data(struct atmel_mci *host, struct mmc_data *data)
{
u32 iflags;
......@@ -685,7 +737,7 @@ static u32 atmci_submit_data(struct atmel_mci *host, struct mmc_data *data)
host->data = data;
iflags = ATMCI_DATA_ERROR_FLAGS;
if (atmci_submit_data_dma(host, data)) {
if (atmci_prepare_data_dma(host, data)) {
host->data_chan = NULL;
/*
......@@ -731,6 +783,8 @@ static void atmci_start_request(struct atmel_mci *host,
mci_writel(host, CR, MCI_CR_SWRST);
mci_writel(host, CR, MCI_CR_MCIEN);
mci_writel(host, MR, host->mode_reg);
if (atmci_is_mci2())
mci_writel(host, CFG, host->cfg_reg);
host->need_reset = false;
}
mci_writel(host, SDCR, slot->sdc_reg);
......@@ -746,6 +800,7 @@ static void atmci_start_request(struct atmel_mci *host,
while (!(mci_readl(host, SR) & MCI_CMDRDY))
cpu_relax();
}
iflags = 0;
data = mrq->data;
if (data) {
atmci_set_timeout(host, slot, data);
......@@ -755,15 +810,17 @@ static void atmci_start_request(struct atmel_mci *host,
| MCI_BLKLEN(data->blksz));
dev_vdbg(&slot->mmc->class_dev, "BLKR=0x%08x\n",
MCI_BCNT(data->blocks) | MCI_BLKLEN(data->blksz));
iflags |= atmci_prepare_data(host, data);
}
iflags = MCI_CMDRDY;
iflags |= MCI_CMDRDY;
cmd = mrq->cmd;
cmdflags = atmci_prepare_command(slot->mmc, cmd);
atmci_start_command(host, cmd, cmdflags);
if (data)
iflags |= atmci_submit_data(host, data);
atmci_submit_data(host);
if (mrq->stop) {
host->stop_cmdr = atmci_prepare_command(slot->mmc, mrq->stop);
......@@ -859,6 +916,8 @@ static void atmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
clk_enable(host->mck);
mci_writel(host, CR, MCI_CR_SWRST);
mci_writel(host, CR, MCI_CR_MCIEN);
if (atmci_is_mci2())
mci_writel(host, CFG, host->cfg_reg);
}
/*
......@@ -1097,6 +1156,8 @@ static void atmci_detect_change(unsigned long data)
mci_writel(host, CR, MCI_CR_SWRST);
mci_writel(host, CR, MCI_CR_MCIEN);
mci_writel(host, MR, host->mode_reg);
if (atmci_is_mci2())
mci_writel(host, CFG, host->cfg_reg);
host->data = NULL;
host->cmd = NULL;
......@@ -1620,6 +1681,10 @@ static void atmci_configure_dma(struct atmel_mci *host)
}
if (!host->dma.chan)
dev_notice(&host->pdev->dev, "DMA not available, using PIO\n");
else
dev_info(&host->pdev->dev,
"Using %s for DMA transfers\n",
dma_chan_name(host->dma.chan));
}
#else
static void atmci_configure_dma(struct atmel_mci *host) {}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment