Commit 75f2d3ea authored by Ben Hutchings's avatar Ben Hutchings Committed by Jeff Garzik

[netdrvr] sfc: Add phy_flash_cfg module parameter and implementation

The 10Xpress PHY supports flash upgrades through MDIO, but needs to be
put in upgrade mode at power-up.  This adds a module parameter and other
logic to support that.
Signed-off-by: default avatarBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: default avatarJeff Garzik <jgarzik@redhat.com>
parent b9b39b62
......@@ -22,5 +22,7 @@ enum efx_board_type {
extern int efx_set_board_info(struct efx_nic *efx, u16 revision_info);
extern int sfe4001_poweron(struct efx_nic *efx);
extern void sfe4001_poweroff(struct efx_nic *efx);
/* Are we putting the PHY into flash config mode */
extern unsigned int sfe4001_phy_flash_cfg;
#endif
......@@ -69,6 +69,10 @@ static int falcon_reset_xmac(struct efx_nic *efx)
udelay(10);
}
/* This often fails when DSP is disabled, ignore it */
if (sfe4001_phy_flash_cfg != 0)
return 0;
EFX_ERR(efx, "timed out waiting for XMAC core reset\n");
return -ETIMEDOUT;
}
......
......@@ -130,6 +130,15 @@ void sfe4001_poweroff(struct efx_nic *efx)
(void) efx_i2c_read(i2c, MAX6647, RSL, &in, 1);
}
/* The P0_EN_3V3X line on SFE4001 boards (from A2 onward) is connected
* to the FLASH_CFG_1 input on the DSP. We must keep it high at power-
* up to allow writing the flash (done through MDIO from userland).
*/
unsigned int sfe4001_phy_flash_cfg;
module_param_named(phy_flash_cfg, sfe4001_phy_flash_cfg, uint, 0444);
MODULE_PARM_DESC(phy_flash_cfg,
"Force PHY to enter flash configuration mode");
/* This board uses an I2C expander to provider power to the PHY, which needs to
* be turned on before the PHY can be used.
* Context: Process context, rtnl lock held
......@@ -203,6 +212,8 @@ int sfe4001_poweron(struct efx_nic *efx)
out = 0xff & ~((1 << P0_EN_1V2_LBN) | (1 << P0_EN_2V5_LBN) |
(1 << P0_EN_3V3X_LBN) | (1 << P0_EN_5V_LBN) |
(1 << P0_X_TRST_LBN));
if (sfe4001_phy_flash_cfg)
out |= 1 << P0_EN_3V3X_LBN;
rc = efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1);
if (rc)
......@@ -226,6 +237,9 @@ int sfe4001_poweron(struct efx_nic *efx)
if (in & (1 << P1_AFE_PWD_LBN))
goto done;
/* DSP doesn't look powered in flash config mode */
if (sfe4001_phy_flash_cfg)
goto done;
} while (++count < 20);
EFX_INFO(efx, "timed out waiting for power\n");
......
......@@ -199,10 +199,12 @@ static int tenxpress_phy_init(struct efx_nic *efx)
tenxpress_set_state(efx, TENXPRESS_STATUS_NORMAL);
rc = mdio_clause45_wait_reset_mmds(efx,
TENXPRESS_REQUIRED_DEVS);
if (rc < 0)
goto fail;
if (!sfe4001_phy_flash_cfg) {
rc = mdio_clause45_wait_reset_mmds(efx,
TENXPRESS_REQUIRED_DEVS);
if (rc < 0)
goto fail;
}
rc = mdio_clause45_check_mmds(efx, TENXPRESS_REQUIRED_DEVS, 0);
if (rc < 0)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment