Commit 768716f4 authored by Michael Heimpold's avatar Michael Heimpold Committed by Shawn Guo

ARM: dts: imx28-duckbill: update to match vendor distributed DT

This patch updates the Duckbill device tree and synchronize it with
the vendor distributed file. The changes in mostly pin-muxing stuff,
but also some minor fixes. In detail:
- enable SPI pins
- enable I2C pins
- enable UART pins
- enable LRADC pin
- adjust USB DR mode
- add default triggers for LEDs
- get rid of regulators simple-bus container
- adjust phy reset duration
  According to phy datasheet, 25ms are sufficient. This also reduces
  the time to boot the system.
Signed-off-by: default avatarMichael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: default avatarShawn Guo <shawnguo@kernel.org>
parent 620885e8
/*
* Copyright (C) 2013 Michael Heimpold <mhei@heimpold.de>
* Copyright (C) 2013-2014,2016 Michael Heimpold <mhei@heimpold.de>
* Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
......@@ -10,6 +11,7 @@
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include "imx28.dtsi"
/ {
......@@ -32,6 +34,13 @@ ssp0: ssp@80010000 {
status = "okay";
};
ssp2: ssp@80014000 {
compatible = "fsl,imx28-spi";
pinctrl-names = "default";
pinctrl-0 = <&spi2_pins_a>;
status = "okay";
};
pinctrl@80018000 {
pinctrl-names = "default";
pinctrl-0 = <&hog_pins_a>;
......@@ -39,14 +48,24 @@ pinctrl@80018000 {
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */
MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_phy_reset_pin: mac0-phy-reset@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
led_pins_a: led_gpio@0 {
led_pins: leds@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_AUART1_RX__GPIO_3_4
......@@ -60,6 +79,22 @@ MX28_PAD_AUART1_TX__GPIO_3_5
};
apbx@80040000 {
lradc@80050000 {
status = "okay";
};
i2c0: i2c@80058000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
};
auart0: serial@8006a000 {
pinctrl-names = "default";
pinctrl-0 = <&auart0_2pins_a>;
status = "okay";
};
duart: serial@80074000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_a>;
......@@ -75,47 +110,43 @@ usbphy0: usbphy@8007c000 {
ahb@80080000 {
usb0: usb@80080000 {
status = "okay";
dr_mode = "peripheral";
};
mac0: ethernet@800f0000 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>;
pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
phy-supply = <&reg_3p3v>;
phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
phy-reset-duration = <100>;
phy-reset-duration = <25>;
status = "okay";
};
};
regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
reg_3p3v: regulator@0 {
compatible = "regulator-fixed";
reg = <0>;
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pins_a>;
pinctrl-0 = <&led_pins>;
status {
label = "duckbill:green:status";
gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
};
failure {
status-red {
label = "duckbill:red:status";
gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "default-on";
};
status-green {
label = "duckbill:green:status";
gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment