Commit 76bf85cc authored by William Wu's avatar William Wu Committed by Felipe Balbi

usb: dwc3: rockchip: add devicetree bindings documentation

This patch adds the devicetree documentation required for Rockchip
USB3.0 core wrapper consisting of USB3.0 IP from Synopsys.

It supports DRD mode, and could operate in device mode (SS, HS, FS)
and host mode (SS, HS, FS, LS).
Signed-off-by: default avatarWilliam Wu <william.wu@rock-chips.com>
Acked-by: default avatarRob Herring <robh@kernel.org>
Signed-off-by: default avatarFelipe Balbi <felipe.balbi@linux.intel.com>
parent 00fe081d
Rockchip SuperSpeed DWC3 USB SoC controller
Required properties:
- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC
- clocks: A list of phandle + clock-specifier pairs for the
clocks listed in clock-names
- clock-names: Should contain the following:
"ref_clk" Controller reference clk, have to be 24 MHz
"suspend_clk" Controller suspend clk, have to be 24 MHz or 32 KHz
"bus_clk" Master/Core clock, have to be >= 62.5 MHz for SS
operation and >= 30MHz for HS operation
"grf_clk" Controller grf clk
Required child node:
A child node must exist to represent the core DWC3 IP block. The name of
the node is not important. The content of the node is defined in dwc3.txt.
Phy documentation is provided in the following places:
Documentation/devicetree/bindings/phy/rockchip,dwc3-usb-phy.txt
Example device nodes:
usbdrd3_0: usb@fe800000 {
compatible = "rockchip,rk3399-dwc3";
clocks = <&cru SCLK_USB3OTG0_REF>, <&cru SCLK_USB3OTG0_SUSPEND>,
<&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_GRF>;
clock-names = "ref_clk", "suspend_clk",
"bus_clk", "grf_clk";
#address-cells = <2>;
#size-cells = <2>;
ranges;
status = "disabled";
usbdrd_dwc3_0: dwc3@fe800000 {
compatible = "snps,dwc3";
reg = <0x0 0xfe800000 0x0 0x100000>;
interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
dr_mode = "otg";
status = "disabled";
};
};
usbdrd3_1: usb@fe900000 {
compatible = "rockchip,rk3399-dwc3";
clocks = <&cru SCLK_USB3OTG1_REF>, <&cru SCLK_USB3OTG1_SUSPEND>,
<&cru ACLK_USB3OTG1>, <&cru ACLK_USB3_GRF>;
clock-names = "ref_clk", "suspend_clk",
"bus_clk", "grf_clk";
#address-cells = <2>;
#size-cells = <2>;
ranges;
status = "disabled";
usbdrd_dwc3_1: dwc3@fe900000 {
compatible = "snps,dwc3";
reg = <0x0 0xfe900000 0x0 0x100000>;
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
dr_mode = "otg";
status = "disabled";
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment