ARM: dts: sun8i-a?3-q8-tablet.dts: Add full otg support

Now that we've all the necessary bits in place we can enable
full otg support on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

arch/arm/boot/dts/sun8i-a23-q8-tablet.dts

@@ -48,18 +48,3 @@ / {
 	model = "Q8 A23 Tablet";
 	compatible = "allwinner,q8-a23", "allwinner,sun8i-a23";
 };
-
-/*
- * FIXME for now we only support host mode and rely on u-boot to have
- * turned on Vbus which is controlled by the axp223 pmic on the board.
- *
- * Once we have axp223 support we should switch to fully supporting otg.
- */
-&usb_otg {
-	dr_mode = "host";
-	status = "okay";
-};
-
-&usbphy {
-	status = "okay";
-};

arch/arm/boot/dts/sun8i-a33-q8-tablet.dts

@@ -48,18 +48,3 @@ / {
 	model = "Q8 A33 Tablet";
 	compatible = "allwinner,q8-a33", "allwinner,sun8i-a33";
 };
-
-/*
- * FIXME for now we only support host mode and rely on u-boot to have
- * turned on Vbus which is controlled by the axp223 pmic on the board.
- *
- * Once we have axp223 support we should switch to fully supporting otg.
- */
-&usb_otg {
-	dr_mode = "host";
-	status = "okay";
-};
-
-&usbphy {
-	status = "okay";
-};

arch/arm/boot/dts/sun8i-q8-common.dtsi

@@ -87,6 +87,13 @@ mmc0_cd_pin_q8: mmc0_cd_pin@0 {
 		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
 		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 	};
+
+	usb0_id_detect_pin: usb0_id_detect_pin@0 {
+		allwinner,pins = "PH8";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
 };
 
 &r_rsb {
@@ -98,6 +105,7 @@ axp22x: pmic@3a3 {
 		interrupt-parent = <&nmi_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		eldoin-supply = <&reg_dcdc1>;
+		x-powers,drive-vbus-en;
 	};
 };
 
@@ -163,6 +171,11 @@ &reg_dcdc5 {
 	regulator-name = "vcc-dram";
 };
 
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
 &reg_rtc_ldo {
 	regulator-name = "vcc-rtc";
 };
@@ -176,3 +189,21 @@ &r_uart {
 &simplefb_lcd {
 	vcc-lcd-supply = <&reg_dc1sw>;
 };
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_id_detect_pin>;
+	usb0_id_det-gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+	usb0_vbus_power-supply = <&usb_power_supply>;
+	usb0_vbus-supply = <&reg_drivevbus>;
+	status = "okay";
+};