Commit 77d28a4f authored by Jeff Garzik's avatar Jeff Garzik

Add several new ethtool commands:

coalescing, ring params, pause params, hw csum disable/enable,
scatter-gather enable/disable
parent 041cc5cb
......@@ -72,6 +72,144 @@ struct ethtool_eeprom {
u32 len; /* in bytes */
u8 data[0];
};
/* for configuring coalescing parameters of chip */
struct ethtool_coalesce {
u32 cmd; /* ETHTOOL_{G,S}COALESCE */
/* How many usecs to delay an RX interrupt after
* a packet arrives. If 0, only rx_max_coalesced_frames
* is used.
*/
u32 rx_coalesce_usecs;
/* How many packets to delay an RX interrupt after
* a packet arrives. If 0, only rx_coalesce_usecs is
* used. It is illegal to set both usecs and max frames
* to zero as this would cause RX interrupts to never be
* generated.
*/
u32 rx_max_coalesced_frames;
/* Same as above two parameters, except that these values
* apply while an IRQ is being services by the host. Not
* all cards support this feature and the values are ignored
* in that case.
*/
u32 rx_coalesce_usecs_irq;
u32 rx_max_coalesced_frames_irq;
/* How many usecs to delay a TX interrupt after
* a packet is sent. If 0, only tx_max_coalesced_frames
* is used.
*/
u32 tx_coalesce_usecs;
/* How many packets to delay a TX interrupt after
* a packet is sent. If 0, only tx_coalesce_usecs is
* used. It is illegal to set both usecs and max frames
* to zero as this would cause TX interrupts to never be
* generated.
*/
u32 tx_max_coalesced_frames;
/* Same as above two parameters, except that these values
* apply while an IRQ is being services by the host. Not
* all cards support this feature and the values are ignored
* in that case.
*/
u32 tx_coalesce_usecs_irq;
u32 tx_max_coalesced_frames_irq;
/* How many usecs to delay in-memory statistics
* block updates. Some drivers do not have an in-memory
* statistic block, and in such cases this value is ignored.
* This value must not be zero.
*/
u32 stats_block_coalesce_usecs;
/* Adaptive RX/TX coalescing is an algorithm implemented by
* some drivers to improve latency under low packet rates and
* improve throughput under high packet rates. Some drivers
* only implement one of RX or TX adaptive coalescing. Anything
* not implemented by the driver causes these values to be
* silently ignored.
*/
u32 use_adaptive_rx_coalesce;
u32 use_adaptive_tx_coalesce;
/* When the packet rate (measured in packets per second)
* is below pkt_rate_low, the {rx,tx}_*_low parameters are
* used.
*/
u32 pkt_rate_low;
u32 rx_coalesce_usecs_low;
u32 rx_max_coalesced_frames_low;
u32 tx_coalesce_usecs_low;
u32 tx_max_coalesced_frames_low;
/* When the packet rate is below pkt_rate_high but above
* pkt_rate_low (both measured in packets per second) the
* normal {rx,tx}_* coalescing parameters are used.
*/
/* When the packet rate is (measured in packets per second)
* is above pkt_rate_high, the {rx,tx}_*_high parameters are
* used.
*/
u32 pkt_rate_high;
u32 rx_coalesce_usecs_high;
u32 rx_max_coalesced_frames_high;
u32 tx_coalesce_usecs_high;
u32 tx_max_coalesced_frames_high;
/* How often to do adaptive coalescing packet rate sampling,
* measured in seconds. Must not be zero.
*/
u32 rate_sample_interval;
};
/* for configuring RX/TX ring parameters */
struct ethtool_ringparam {
u32 cmd; /* ETHTOOL_{G,S}RINGPARAM */
/* Read only attributes. These indicate the maximum number
* of pending RX/TX ring entries the driver will allow the
* user to set.
*/
u32 rx_max_pending;
u32 rx_mini_max_pending;
u32 rx_jumbo_max_pending;
u32 tx_max_pending;
/* Values changeable by the user. The valid values are
* in the range 1 to the "*_max_pending" counterpart above.
*/
u32 rx_pending;
u32 rx_mini_pending;
u32 rx_jumbo_pending;
u32 tx_pending;
};
/* for configuring link flow control parameters */
struct ethtool_pauseparam {
u32 cmd; /* ETHTOOL_{G,S}PAUSEPARAM */
/* If the link is being auto-negotiated (via ethtool_cmd.autoneg
* being true) the user may set 'autonet' here non-zero to have the
* pause parameters be auto-negotiated too. In such a case, the
* {rx,tx}_pause values below determine what capabilities are
* advertised.
*
* If 'autoneg' is zero or the link is not being auto-negotiated,
* then {rx,tx}_pause force the driver to use/not-use pause
* flow control.
*/
u32 autoneg;
u32 rx_pause;
u32 tx_pause;
};
/* CMDs currently supported */
#define ETHTOOL_GSET 0x00000001 /* Get settings. */
#define ETHTOOL_SSET 0x00000002 /* Set settings, privileged. */
......@@ -82,9 +220,23 @@ struct ethtool_eeprom {
#define ETHTOOL_GMSGLVL 0x00000007 /* Get driver message level */
#define ETHTOOL_SMSGLVL 0x00000008 /* Set driver msg level, priv. */
#define ETHTOOL_NWAY_RST 0x00000009 /* Restart autonegotiation, priv. */
#define ETHTOOL_GLINK 0x0000000a /* Get link status */
#define ETHTOOL_GLINK 0x0000000a /* Get link status (ethtool_value) */
#define ETHTOOL_GEEPROM 0x0000000b /* Get EEPROM data */
#define ETHTOOL_SEEPROM 0x0000000c /* Set EEPROM data */
#define ETHTOOL_GCOALESCE 0x0000000e /* Get coalesce config */
#define ETHTOOL_SCOALESCE 0x0000000f /* Set coalesce config */
#define ETHTOOL_GRINGPARAM 0x00000010 /* Get ring parameters */
#define ETHTOOL_SRINGPARAM 0x00000011 /* Set ring parameters */
#define ETHTOOL_GPAUSEPARAM 0x00000012 /* Get pause parameters */
#define ETHTOOL_SPAUSEPARAM 0x00000013 /* Set pause parameters */
#define ETHTOOL_GRXCSUM 0x00000014 /* Get RX hw csum enable (ethtool_value) */
#define ETHTOOL_SRXCSUM 0x00000015 /* Set RX hw csum enable (ethtool_value) */
#define ETHTOOL_GTXCSUM 0x00000016 /* Get TX hw csum enable (ethtool_value) */
#define ETHTOOL_STXCSUM 0x00000017 /* Set TX hw csum enable (ethtool_value) */
#define ETHTOOL_GSG 0x00000018 /* Get scatter-gather enable
* (ethtool_value) */
#define ETHTOOL_SSG 0x00000019 /* Set scatter-gather enable
* (ethtool_value) */
/* compatibility with older code */
#define SPARC_ETH_GSET ETHTOOL_GSET
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment