Commit 7db9af4b authored by Heiko Stübner's avatar Heiko Stübner Committed by Linus Walleij

pinctrl: add function to parse generic pinconfig properties from a dt node

pinconf_generic_parse_dt_config() takes a node as input and generates an
array of generic pinconfig values from the properties of this node.

As I couldn't find a mechanism to count the number of properties of a node
the function uses internally an array to accept one of parameter and copies
the real present options to a smaller variable at its end.
Signed-off-by: default avatarHeiko Stuebner <heiko@sntech.de>
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
parent 5c0e3580
......@@ -126,3 +126,41 @@ device; they may be grandchildren, for example. Whether this is legal, and
whether there is any interaction between the child and intermediate parent
nodes, is again defined entirely by the binding for the individual pin
controller device.
== Using generic pinconfig options ==
Generic pinconfig parameters can be used by defining a separate node containing
the applicable parameters (and optional values), like:
pcfg_pull_up: pcfg_pull_up {
bias-pull-up;
drive-strength = <20>;
};
This node should then be referenced in the appropriate pinctrl node as a phandle
and parsed in the driver using the pinconf_generic_parse_dt_config function.
Supported configuration parameters are:
bias-disable - disable any pin bias
bias-high-impedance - high impedance mode ("third-state", "floating")
bias-bus-hold - latch weakly
bias-pull-up - pull up the pin
bias-pull-down - pull down the pin
bias-pull-pin-default - use pin-default pull state
drive-push-pull - drive actively high and low
drive-open-drain - drive with open drain
drive-open-source - drive with open source
drive-strength - sink or source at most X mA
input-schmitt-enable - enable schmitt-trigger mode
input-schmitt-disable - disable schmitt-trigger mode
input-schmitt - run in schmitt-trigger mode with hysteresis X
input-debounce - debounce mode with debound time X
power-source - select power source X
slew-rate - use slew-rate X
low-power-mode - low power mode
output-low - set the pin to output mode with low level
output-high - set the pin to output mode with high level
More in-depth documentation on these parameters can be found in
<include/linux/pinctrl/pinconfig-generic.h>
......@@ -21,6 +21,7 @@
#include <linux/pinctrl/pinctrl.h>
#include <linux/pinctrl/pinconf.h>
#include <linux/pinctrl/pinconf-generic.h>
#include <linux/of.h>
#include "core.h"
#include "pinconf.h"
......@@ -139,3 +140,83 @@ void pinconf_generic_dump_config(struct pinctrl_dev *pctldev,
}
EXPORT_SYMBOL_GPL(pinconf_generic_dump_config);
#endif
#ifdef CONFIG_OF
struct pinconf_generic_dt_params {
const char * const property;
enum pin_config_param param;
u32 default_value;
};
static struct pinconf_generic_dt_params dt_params[] = {
{ "bias-disable", PIN_CONFIG_BIAS_DISABLE, 0 },
{ "bias-high-impedance", PIN_CONFIG_BIAS_HIGH_IMPEDANCE, 0 },
{ "bias-bus-hold", PIN_CONFIG_BIAS_BUS_HOLD, 0 },
{ "bias-pull-up", PIN_CONFIG_BIAS_PULL_UP, 0 },
{ "bias-pull-down", PIN_CONFIG_BIAS_PULL_DOWN, 0 },
{ "bias-pull-pin-default", PIN_CONFIG_BIAS_PULL_PIN_DEFAULT, 0 },
{ "drive-push-pull", PIN_CONFIG_DRIVE_PUSH_PULL, 0 },
{ "drive-open-drain", PIN_CONFIG_DRIVE_OPEN_DRAIN, 0 },
{ "drive-open-source", PIN_CONFIG_DRIVE_OPEN_SOURCE, 0 },
{ "drive-strength", PIN_CONFIG_DRIVE_STRENGTH, 0 },
{ "input-schmitt-enable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 1 },
{ "input-schmitt-disable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 0 },
{ "input-schmitt", PIN_CONFIG_INPUT_SCHMITT, 0 },
{ "input-debounce", PIN_CONFIG_INPUT_DEBOUNCE, 0 },
{ "power-source", PIN_CONFIG_POWER_SOURCE, 0 },
{ "slew-rate", PIN_CONFIG_SLEW_RATE, 0 },
{ "low-power-mode", PIN_CONFIG_LOW_POWER_MODE, 0 },
{ "output-low", PIN_CONFIG_OUTPUT, 0, },
{ "output-high", PIN_CONFIG_OUTPUT, 1, },
};
/**
* pinconf_generic_parse_dt_config()
* parse the config properties into generic pinconfig values.
* @np: node containing the pinconfig properties
* @configs: array with nconfigs entries containing the generic pinconf values
* @nconfigs: umber of configurations
*/
int pinconf_generic_parse_dt_config(struct device_node *np,
unsigned long **configs,
unsigned int *nconfigs)
{
unsigned long cfg[ARRAY_SIZE(dt_params)];
unsigned int ncfg = 0;
int ret;
int i;
u32 val;
if (!np)
return -EINVAL;
for (i = 0; i < ARRAY_SIZE(dt_params); i++) {
struct pinconf_generic_dt_params *par = &dt_params[i];
ret = of_property_read_u32(np, par->property, &val);
/* property not found */
if (ret == -EINVAL)
continue;
/* use default value, when no value is specified */
if (ret)
val = par->default_value;
pr_debug("found %s with value %u\n", par->property, val);
cfg[ncfg] = pinconf_to_config_packed(par->param, val);
ncfg++;
}
/*
* Now limit the number of configs to the real number of
* found properties.
*/
*configs = kzalloc(ncfg * sizeof(unsigned long), GFP_KERNEL);
if (!*configs)
return -ENOMEM;
memcpy(*configs, &cfg, ncfg * sizeof(unsigned long));
*nconfigs = ncfg;
return 0;
}
#endif
......@@ -123,3 +123,9 @@ static inline void pinconf_generic_dump_config(struct pinctrl_dev *pctldev,
return;
}
#endif
#if defined(CONFIG_GENERIC_PINCONF) && defined(CONFIG_OF)
int pinconf_generic_parse_dt_config(struct device_node *np,
unsigned long **configs,
unsigned int *nconfigs);
#endif
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment