Commit 800974ac authored by Dongjin Kim's avatar Dongjin Kim Committed by Kukjin Kim

ARM: dts: Add board dts file for ODROID-X

Add initial DT for Hardkernel's ODROID-X board based on EXYNOS4412
SoC. This patch including adds the node to support fixed voltage for
peripherals like LED, ethernet controller, and this patch adds GPIO
connected LEDS on ODROID-X board and configure its properties like
following:
LED1: use 'heartbeat' trigger, blinking while the board is running.
LED2: use 'mmc0' trigger, on when mmc0 is accessing.

And adds the device node to support eMMC storage on SDCARD4 ports,
controlled by MSHC.
Signed-off-by: default avatarDongjin Kim <tobetter@gmail.com>
Acked-by: default avatarOlof Johansson <olof@lixom.net>
[kgene.kim@samsung.com: squashed into one commit as per Olof's comment]
Signed-off-by: default avatarKukjin Kim <kgene.kim@samsung.com>
parent 2107673e
...@@ -42,6 +42,7 @@ dtb-$(CONFIG_ARCH_DOVE) += dove-cm-a510.dtb \ ...@@ -42,6 +42,7 @@ dtb-$(CONFIG_ARCH_DOVE) += dove-cm-a510.dtb \
dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
exynos4210-smdkv310.dtb \ exynos4210-smdkv310.dtb \
exynos4210-trats.dtb \ exynos4210-trats.dtb \
exynos4412-odroidx.dtb \
exynos4412-smdk4412.dtb \ exynos4412-smdk4412.dtb \
exynos4412-origen.dtb \ exynos4412-origen.dtb \
exynos5250-smdk5250.dtb \ exynos5250-smdk5250.dtb \
......
/*
* Hardkernel's Exynos4412 based ODROID-X board device tree source
*
* Copyright (c) 2012 Dongjin Kim <tobetter@gmail.com>
*
* Device tree source file for Hardkernel's ODROID-X board which is based on
* Samsung's Exynos4412 SoC.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/dts-v1/;
/include/ "exynos4412.dtsi"
/ {
model = "Hardkernel ODROID-X board based on Exynos4412";
compatible = "hardkernel,odroid-x", "samsung,exynos4412";
memory {
reg = <0x40000000 0x40000000>;
};
leds {
compatible = "gpio-leds";
led1 {
label = "led1:heart";
gpios = <&gpc1 0 1>;
default-state = "on";
linux,default-trigger = "heartbeat";
};
led2 {
label = "led2:mmc0";
gpios = <&gpc1 2 1>;
default-state = "on";
linux,default-trigger = "mmc0";
};
};
mshc@12550000 {
pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
pinctrl-names = "default";
status = "okay";
num-slots = <1>;
supports-highspeed;
broken-cd;
fifo-depth = <0x80>;
card-detect-delay = <200>;
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <2 3 3>;
samsung,dw-mshc-ddr-timing = <1 2 3>;
slot@0 {
reg = <0>;
bus-width = <8>;
};
};
regulator_p3v3 {
compatible = "regulator-fixed";
regulator-name = "p3v3_en";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpa1 1 1>;
enable-active-high;
regulator-boot-on;
};
sdhci@12530000 {
bus-width = <4>;
pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
pinctrl-names = "default";
status = "okay";
};
serial@13800000 {
status = "okay";
};
serial@13810000 {
status = "okay";
};
serial@13820000 {
status = "okay";
};
serial@13830000 {
status = "okay";
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment