pmdomain: arm_scmi: Move Kconfig options to the pmdomain subsystem

The Kconfig options belongs closer to the corresponding implementations,
hence let's move them from the firmware to the pmdomain subsystem.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20231123120847.2825444-1-sudeep.holla@arm.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

drivers/firmware/arm_scmi/Kconfig

@@ -168,31 +168,6 @@ config ARM_SCMI_TRANSPORT_VIRTIO_ATOMIC_ENABLE
 
 endif #ARM_SCMI_PROTOCOL
 
-config ARM_SCMI_POWER_DOMAIN
-	tristate "SCMI power domain driver"
-	depends on ARM_SCMI_PROTOCOL || (COMPILE_TEST && OF)
-	default y
-	select PM_GENERIC_DOMAINS if PM
-	help
-	  This enables support for the SCMI power domains which can be
-	  enabled or disabled via the SCP firmware
-
-	  This driver can also be built as a module.  If so, the module
-	  will be called scmi_pm_domain. Note this may needed early in boot
-	  before rootfs may be available.
-
-config ARM_SCMI_PERF_DOMAIN
-	tristate "SCMI performance domain driver"
-	depends on ARM_SCMI_PROTOCOL || (COMPILE_TEST && OF)
-	default y
-	select PM_GENERIC_DOMAINS if PM
-	help
-	  This enables support for the SCMI performance domains which can be
-	  enabled or disabled via the SCP firmware.
-
-	  This driver can also be built as a module. If so, the module will be
-	  called scmi_perf_domain.
-
 config ARM_SCMI_POWER_CONTROL
 	tristate "SCMI system power control driver"
 	depends on ARM_SCMI_PROTOCOL || (COMPILE_TEST && OF)

drivers/pmdomain/Kconfig

@@ -4,6 +4,7 @@ menu "PM Domains"
 source "drivers/pmdomain/actions/Kconfig"
 source "drivers/pmdomain/amlogic/Kconfig"
 source "drivers/pmdomain/apple/Kconfig"
+source "drivers/pmdomain/arm/Kconfig"
 source "drivers/pmdomain/bcm/Kconfig"
 source "drivers/pmdomain/imx/Kconfig"
 source "drivers/pmdomain/mediatek/Kconfig"

drivers/pmdomain/arm/Kconfig

+# SPDX-License-Identifier: GPL-2.0-only
+config ARM_SCMI_PERF_DOMAIN
+	tristate "SCMI performance domain driver"
+	depends on ARM_SCMI_PROTOCOL || (COMPILE_TEST && OF)
+	default y
+	select PM_GENERIC_DOMAINS if PM
+	help
+	  This enables support for the SCMI performance domains which can be
+	  enabled or disabled via the SCP firmware.
+
+	  This driver can also be built as a module. If so, the module will be
+	  called scmi_perf_domain.
+
+config ARM_SCMI_POWER_DOMAIN
+	tristate "SCMI power domain driver"
+	depends on ARM_SCMI_PROTOCOL || (COMPILE_TEST && OF)
+	default y
+	select PM_GENERIC_DOMAINS if PM
+	help
+	  This enables support for the SCMI power domains which can be
+	  enabled or disabled via the SCP firmware
+
+	  This driver can also be built as a module. If so, the module
+	  will be called scmi_pm_domain. Note this may needed early in boot
+	  before rootfs may be available.