Merge tag 'x86-entry-2024-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull x86 entry update from Thomas Gleixner:
 "A single update for the x86 entry code:

  The current CR3 handling for kernel page table isolation in the
  paranoid return paths which are relevant for #NMI, #MCE, #VC, #DB and
  #DF is unconditionally writing CR3 with the value retrieved on
  exception entry.

  In the vast majority of cases when returning to the kernel this is a
  pointless exercise because CR3 was not modified on exception entry.
  The only situation where this is necessary is when the exception
  interrupts a entry from user before switching to kernel CR3 or
  interrupts an exit to user after switching back to user CR3.

  As CR3 writes can be expensive on some systems this becomes measurable
  overhead with high frequency #NMIs such as perf.

  Avoid this overhead by checking the CR3 value, which was saved on
  entry, and write it back to CR3 only when it is a user CR3"

* tag 'x86-entry-2024-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/entry: Avoid redundant CR3 write on paranoid returns

arch/x86/entry/calling.h

@@ -244,17 +244,19 @@ For 32-bit we have the following conventions - kernel is built with
 .Ldone_\@:
 .endm
 
-.macro RESTORE_CR3 scratch_reg:req save_reg:req
+/* Restore CR3 from a kernel context. May restore a user CR3 value. */
+.macro PARANOID_RESTORE_CR3 scratch_reg:req save_reg:req
 	ALTERNATIVE "jmp .Lend_\@", "", X86_FEATURE_PTI
 
-	ALTERNATIVE "jmp .Lwrcr3_\@", "", X86_FEATURE_PCID
-
 	/*
-	 * KERNEL pages can always resume with NOFLUSH as we do
-	 * explicit flushes.
+	 * If CR3 contained the kernel page tables at the paranoid exception
+	 * entry, then there is nothing to restore as CR3 is not modified while
+	 * handling the exception.
 	 */
 	bt	$PTI_USER_PGTABLE_BIT, \save_reg
-	jnc	.Lnoflush_\@
+	jnc	.Lend_\@
+
+	ALTERNATIVE "jmp .Lwrcr3_\@", "", X86_FEATURE_PCID
 
 	/*
 	 * Check if there's a pending flush for the user ASID we're
@@ -262,20 +264,12 @@ For 32-bit we have the following conventions - kernel is built with
 	 */
 	movq	\save_reg, \scratch_reg
 	andq	$(0x7FF), \scratch_reg
-	bt	\scratch_reg, THIS_CPU_user_pcid_flush_mask
-	jnc	.Lnoflush_\@
-
 	btr	\scratch_reg, THIS_CPU_user_pcid_flush_mask
-	jmp	.Lwrcr3_\@
+	jc	.Lwrcr3_\@
 
-.Lnoflush_\@:
 	SET_NOFLUSH_BIT \save_reg
 
 .Lwrcr3_\@:
-	/*
-	 * The CR3 write could be avoided when not changing its value,
-	 * but would require a CR3 read *and* a scratch register.
-	 */
 	movq	\save_reg, %cr3
 .Lend_\@:
 .endm
@@ -290,7 +284,7 @@ For 32-bit we have the following conventions - kernel is built with
 .endm
 .macro SAVE_AND_SWITCH_TO_KERNEL_CR3 scratch_reg:req save_reg:req
 .endm
-.macro RESTORE_CR3 scratch_reg:req save_reg:req
+.macro PARANOID_RESTORE_CR3 scratch_reg:req save_reg:req
 .endm
 
 #endif

arch/x86/entry/entry_64.S

@@ -970,14 +970,14 @@ SYM_CODE_START_LOCAL(paranoid_exit)
 	IBRS_EXIT save_reg=%r15
 
 	/*
-	 * The order of operations is important. RESTORE_CR3 requires
+	 * The order of operations is important. PARANOID_RESTORE_CR3 requires
 	 * kernel GSBASE.
 	 *
 	 * NB to anyone to try to optimize this code: this code does
 	 * not execute at all for exceptions from user mode. Those
 	 * exceptions go through error_return instead.
 	 */
-	RESTORE_CR3	scratch_reg=%rax save_reg=%r14
+	PARANOID_RESTORE_CR3 scratch_reg=%rax save_reg=%r14
 
 	/* Handle the three GSBASE cases */
 	ALTERNATIVE "jmp .Lparanoid_exit_checkgs", "", X86_FEATURE_FSGSBASE
@@ -1406,8 +1406,7 @@ end_repeat_nmi:
 	/* Always restore stashed SPEC_CTRL value (see paranoid_entry) */
 	IBRS_EXIT save_reg=%r15
 
-	/* Always restore stashed CR3 value (see paranoid_entry) */
-	RESTORE_CR3 scratch_reg=%r15 save_reg=%r14
+	PARANOID_RESTORE_CR3 scratch_reg=%r15 save_reg=%r14
 
 	/*
 	 * The above invocation of paranoid_entry stored the GSBASE