Commit 86c35960 authored by Jon Hunter's avatar Jon Hunter Committed by Tony Lindgren

ARM: OMAP2420: Fix ethernet support for OMAP2420 H4

Ethernet is not currently working on the OMAP2420 H4 board. In commit
f6049312 (ARM: OMAP: abstract debug card setup (smc, leds)) the function
h4_init_smc91x() that initialised the ethernet controller was renamed to
h4_init_debug() but was never called when initialising the board.

Adding a call to h4_init_debug() fixes ethernet support, however,
instead of using the legacy H4 code migrate the H4 to use the
gpmc_smc91x_init() function instead and remove the legacy H4 code.
Signed-off-by: default avatarJon Hunter <jon-hunter@ti.com>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
parent 421e8450
......@@ -27,14 +27,12 @@
#include <linux/io.h>
#include <linux/input/matrix_keypad.h>
#include <linux/mfd/menelaus.h>
#include <linux/omap-dma.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <linux/omap-dma.h>
#include <plat/debug-devices.h>
#include <video/omapdss.h>
#include <video/omap-panel-generic-dpi.h>
......@@ -42,11 +40,9 @@
#include "mux.h"
#include "control.h"
#include "gpmc.h"
#include "gpmc-smc91x.h"
#define H4_FLASH_CS 0
#define H4_SMC91X_CS 1
#define H4_ETHR_GPIO_IRQ 92
#if defined(CONFIG_KEYBOARD_MATRIX) || defined(CONFIG_KEYBOARD_MATRIX_MODULE)
static const uint32_t board_matrix_keys[] = {
......@@ -250,71 +246,31 @@ static u32 is_gpmc_muxed(void)
return 0;
}
static inline void __init h4_init_debug(void)
{
int eth_cs;
unsigned long cs_mem_base;
unsigned int muxed, rate;
struct clk *gpmc_fck;
eth_cs = H4_SMC91X_CS;
#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91x_MODULE)
gpmc_fck = clk_get(NULL, "gpmc_fck"); /* Always on ENABLE_ON_INIT */
if (IS_ERR(gpmc_fck)) {
WARN_ON(1);
return;
}
clk_prepare_enable(gpmc_fck);
rate = clk_get_rate(gpmc_fck);
clk_disable_unprepare(gpmc_fck);
clk_put(gpmc_fck);
static struct omap_smc91x_platform_data board_smc91x_data = {
.cs = 1,
.gpio_irq = 92,
.flags = GPMC_TIMINGS_SMC91C96 | IORESOURCE_IRQ_LOWLEVEL,
};
static void __init board_smc91x_init(void)
{
if (is_gpmc_muxed())
muxed = 0x200;
else
muxed = 0;
/* Make sure CS1 timings are correct */
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG1,
0x00011000 | muxed);
if (rate >= 160000000) {
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f01);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080803);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1c0b1c0a);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
} else if (rate >= 130000000) {
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
} else {/* rate = 100000000 */
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x031A1F1F);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000003C2);
}
if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
printk(KERN_ERR "Failed to request GPMC mem for smc91x\n");
goto out;
}
board_smc91x_data.flags |= GPMC_MUX_ADD_DATA;
udelay(100);
omap_mux_init_gpio(board_smc91x_data.gpio_irq, OMAP_PIN_INPUT);
gpmc_smc91x_init(&board_smc91x_data);
}
omap_mux_init_gpio(92, 0);
if (debug_card_init(cs_mem_base, H4_ETHR_GPIO_IRQ) < 0)
gpmc_cs_free(eth_cs);
#else
out:
clk_disable_unprepare(gpmc_fck);
clk_put(gpmc_fck);
static inline void board_smc91x_init(void)
{
}
#endif
static void __init h4_init_flash(void)
{
unsigned long base;
......@@ -371,6 +327,7 @@ static void __init omap_h4_init(void)
omap_serial_init();
omap_sdrc_init(NULL, NULL);
h4_init_flash();
board_smc91x_init();
omap_display_init(&h4_dss_data);
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment