Commit 86c62fab authored by Ben Dooks's avatar Ben Dooks Committed by Jeff Garzik

DM9000: Remove barely used SROM array read.

The srom array in the board data is only being used in the device probe
routines. The probe also only uses the first 6 bytes of an array
we spend 512ms reading 128 bytes from. Change to reading the
MAC area directly to the MAC address structure.

As a side product, we rename the read_srom_word to dm9000_read_eeprom
to bring it into line with the rest of the driver. No change is made
to the delay in this function, which will be dealt with in a later
patch.
Signed-off-by: default avatarBen Dooks <ben-linux@fluff.org>
Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
parent 321f69a4
......@@ -132,7 +132,6 @@ typedef struct board_info {
struct resource *data_req;
struct resource *irq_res;
unsigned char srom[128];
spinlock_t lock;
struct mii_if_info mii;
......@@ -166,7 +165,8 @@ static irqreturn_t dm9000_interrupt(int, void *);
static int dm9000_phy_read(struct net_device *dev, int phyaddr_unsused, int reg);
static void dm9000_phy_write(struct net_device *dev, int phyaddr_unused, int reg,
int value);
static u16 read_srom_word(board_info_t *, int);
static void dm9000_read_eeprom(board_info_t *, int addr, unsigned char *to);
static void dm9000_rx(struct net_device *);
static void dm9000_hash_table(struct net_device *);
......@@ -630,13 +630,9 @@ dm9000_probe(struct platform_device *pdev)
db->mii.mdio_read = dm9000_phy_read;
db->mii.mdio_write = dm9000_phy_write;
/* Read SROM content */
for (i = 0; i < 64; i++)
((u16 *) db->srom)[i] = read_srom_word(db, i);
/* Set Node Address */
for (i = 0; i < 6; i++)
ndev->dev_addr[i] = db->srom[i];
/* try reading the node address from the attached EEPROM */
for (i = 0; i < 6; i += 2)
dm9000_read_eeprom(db, i / 2, ndev->dev_addr+i);
if (!is_valid_ether_addr(ndev->dev_addr)) {
/* try reading from mac */
......@@ -998,17 +994,19 @@ dm9000_rx(struct net_device *dev)
}
/*
* Read a word data from SROM
* Read a word data from EEPROM
*/
static u16
read_srom_word(board_info_t * db, int offset)
static void
dm9000_read_eeprom(board_info_t * db, int offset, unsigned char *to)
{
iow(db, DM9000_EPAR, offset);
iow(db, DM9000_EPCR, EPCR_ERPRR);
mdelay(8); /* according to the datasheet 200us should be enough,
but it doesn't work */
iow(db, DM9000_EPCR, 0x0);
return (ior(db, DM9000_EPDRL) + (ior(db, DM9000_EPDRH) << 8));
to[0] = ior(db, DM9000_EPDRL);
to[1] = ior(db, DM9000_EPDRH);
}
#ifdef DM9000_PROGRAM_EEPROM
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment