ata: add platform driver for Calxeda AHCI controller

Calxeda highbank SATA phy has intermittent problems bringing up a link
with Gen3 drives. Retrying the phy hard reset can work-around this issue,
but each reset also disables spread spectrum support. The reset function
also needs to reprogram the phy to enable spread spectrum support.

Create a new driver based on ahci_platform to support the Calxeda Highbank
SATA controller.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Documentation/devicetree/bindings/arm/calxeda/combophy.txt

+Calxeda Highbank Combination Phys for SATA
+
+Properties:
+- compatible : Should be "calxeda,hb-combophy"
+- #phy-cells: Should be 1.
+- reg : Address and size for Combination Phy registers.
+- phydev: device ID for programming the combophy.
+
+Example:
+
+	combophy5: combo-phy@fff5d000 {
+		compatible = "calxeda,hb-combophy";
+		#phy-cells = <1>;
+		reg = <0xfff5d000 0x1000>;
+		phydev = <31>;
+	};
+

Documentation/devicetree/bindings/ata/ahci-platform.txt

@@ -8,9 +8,17 @@ Required properties:
 - interrupts        : <interrupt mapping for SATA IRQ>
 - reg               : <registers mapping>
 
+Optional properties:
+- calxeda,port-phys: phandle-combophy and lane assignment, which maps each
+			SATA port to a combophy and a lane within that
+			combophy
+
 Example:
         sata@ffe08000 {
 		compatible = "calxeda,hb-ahci";
                 reg = <0xffe08000 0x1000>;
                 interrupts = <115>;
+		calxeda,port-phys = <&combophy5 0 &combophy0 0 &combophy0 1
+					&combophy0 2 &combophy0 3>;
+
         };

arch/arm/boot/dts/highbank.dts

@@ -121,6 +121,9 @@ sata@ffe08000 {
 			compatible = "calxeda,hb-ahci";
 			reg = <0xffe08000 0x10000>;
 			interrupts = <0 83 4>;
+			calxeda,port-phys = <&combophy5 0 &combophy0 0
+					     &combophy0 1 &combophy0 2
+					     &combophy0 3>;
 		};
 
 		sdhci@ffe0e000 {
@@ -306,5 +309,19 @@ ethernet@fff51000 {
 			reg = <0xfff51000 0x1000>;
 			interrupts = <0 80 4  0 81 4  0 82 4>;
 		};
+
+		combophy0: combo-phy@fff58000 {
+			compatible = "calxeda,hb-combophy";
+			#phy-cells = <1>;
+			reg = <0xfff58000 0x1000>;
+			phydev = <5>;
+		};
+
+		combophy5: combo-phy@fff5d000 {
+			compatible = "calxeda,hb-combophy";
+			#phy-cells = <1>;
+			reg = <0xfff5d000 0x1000>;
+			phydev = <31>;
+		};
 	};
 };

drivers/ata/Kconfig

@@ -214,6 +214,14 @@ config SATA_DWC_VDEBUG
 	help
 	  This option enables the taskfile dumping and NCQ debugging.
 
+config SATA_HIGHBANK
+	tristate "Calxeda Highbank SATA support"
+	help
+	  This option enables support for the Calxeda Highbank SoC's
+	  onboard SATA.
+
+	  If unsure, say N.
+
 config SATA_MV
 	tristate "Marvell SATA support"
 	help

drivers/ata/Makefile

@@ -9,6 +9,7 @@ obj-$(CONFIG_SATA_FSL)		+= sata_fsl.o
 obj-$(CONFIG_SATA_INIC162X)	+= sata_inic162x.o
 obj-$(CONFIG_SATA_SIL24)	+= sata_sil24.o
 obj-$(CONFIG_SATA_DWC)		+= sata_dwc_460ex.o
+obj-$(CONFIG_SATA_HIGHBANK)	+= sata_highbank.o
 
 # SFF w/ custom DMA
 obj-$(CONFIG_PDC_ADMA)		+= pdc_adma.o

drivers/ata/ahci_platform.c

@@ -277,7 +277,6 @@ static int ahci_resume(struct device *dev)
 SIMPLE_DEV_PM_OPS(ahci_pm_ops, ahci_suspend, ahci_resume);
 
 static const struct of_device_id ahci_of_match[] = {
-	{ .compatible = "calxeda,hb-ahci", },
 	{ .compatible = "snps,spear-ahci", },
 	{},
 };