dt-bindings: display: bridge: Add documentation for LT9611

Lontium LT9611 is a DSI to HDMI bridge which supports 2 DSI ports
and I2S port as input and one HDMI port as output
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200723163442.1280414-3-vkoul@kernel.org

Documentation/devicetree/bindings/display/bridge/lontium,lt9611.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/lontium,lt9611.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Lontium LT9611 2 Port MIPI to HDMI Bridge
+
+maintainers:
+  - Vinod Koul <vkoul@kernel.org>
+
+description: |
+  The LT9611 is a bridge device which converts DSI to HDMI
+
+properties:
+  compatible:
+    enum:
+      - lontium,lt9611
+
+  reg:
+    maxItems: 1
+
+  "#sound-dai-cells":
+    const: 1
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+    description: GPIO connected to active high RESET pin.
+
+  vdd-supply:
+    description: Regulator for 1.8V MIPI phy power.
+
+  vcc-supply:
+    description: Regulator for 3.3V IO power.
+
+  ports:
+    type: object
+
+    properties:
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 0
+
+      port@0:
+        type: object
+        description: |
+          Primary MIPI port-1 for MIPI input
+
+        properties:
+          reg:
+            const: 0
+
+        patternProperties:
+          "^endpoint(@[0-9])$":
+            type: object
+            additionalProperties: false
+
+            properties:
+              remote-endpoint:
+                $ref: /schemas/types.yaml#/definitions/phandle
+
+        required:
+          - reg
+
+      port@1:
+        type: object
+        description: |
+          Additional MIPI port-2 for MIPI input, used in combination
+          with primary MIPI port-1 to drive higher resolution displays
+
+        properties:
+          reg:
+            const: 1
+
+        patternProperties:
+          "^endpoint(@[0-9])$":
+            type: object
+            additionalProperties: false
+
+            properties:
+              remote-endpoint:
+                $ref: /schemas/types.yaml#/definitions/phandle
+
+        required:
+          - reg
+
+      port@2:
+        type: object
+        description: |
+          HDMI port for HDMI output
+
+        properties:
+          reg:
+            const: 2
+
+        patternProperties:
+          "^endpoint(@[0-9])$":
+            type: object
+            additionalProperties: false
+
+            properties:
+              remote-endpoint:
+                $ref: /schemas/types.yaml#/definitions/phandle
+
+        required:
+          - reg
+
+    required:
+      - "#address-cells"
+      - "#size-cells"
+      - port@0
+      - port@2
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - vdd-supply
+  - vcc-supply
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c10 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      hdmi-bridge@3b {
+        compatible = "lontium,lt9611";
+        reg = <0x3b>;
+
+        reset-gpios = <&tlmm 128 GPIO_ACTIVE_HIGH>;
+        interrupts-extended = <&tlmm 84 IRQ_TYPE_EDGE_FALLING>;
+
+        vdd-supply = <&lt9611_1v8>;
+        vcc-supply = <&lt9611_3v3>;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+            reg = <0>;
+            lt9611_a: endpoint {
+              remote-endpoint = <&dsi0_out>;
+            };
+          };
+
+          port@1 {
+            reg = <1>;
+            lt9611_b: endpoint {
+              remote-endpoint = <&dsi1_out>;
+            };
+          };
+
+          port@2 {
+            reg = <2>;
+            lt9611_out: endpoint {
+              remote-endpoint = <&hdmi_con>;
+            };
+          };
+        };
+      };
+    };
+
+...