Merge tag 'sunxi-h3-h5-for-4.20' of...

Merge tag 'sunxi-h3-h5-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Allwinner H3 and H5 DT additions for 4.20

This is our usual H3/H5 pull request

The most notable changes are:
  - the video decoding / encoding unit is finally enabled on the H3
  - Mali support for the H5
  - New boards: BananaPi M2+ v1.2, Orange Pi Zero Plus 2 H3 support

* tag 'sunxi-h3-h5-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees
  ARM: dts: sun8i-h3: Add Video Engine and reserved memory nodes
  arm64: dts: allwinner: h5: Add device tree for Bananapi M2 Plus H5
  ARM: dts: sun8i: h3: Split out non-SoC-specific parts of Bananapi M2 Plus
  ARM: dts: sun8i: h3: bpi-m2-plus: Fix address for external RGMII Ethernet PHY
  ARM: dts: sun8i: h3-h5: ir register size should be the whole memory block
  arm64: dts: allwinner: h5: Add device node for Mali-450 GPU
  ARM: dts: sun8i: Add initial Orangepi Zero Plus 2 H3 support
  nvmem: sunxi-sid: add support for H5's SID controller
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt

@@ -7,6 +7,7 @@ Required properties:
   "allwinner,sun8i-a83t-sid"
   "allwinner,sun8i-h3-sid"
   "allwinner,sun50i-a64-sid"
+  "allwinner,sun50i-h5-sid"
 
 - reg: Should contain registers location and length
 

arch/arm/boot/dts/Makefile

@@ -1035,6 +1035,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-h2-plus-orangepi-r1.dtb \
 	sun8i-h2-plus-orangepi-zero.dtb \
 	sun8i-h3-bananapi-m2-plus.dtb \
+	sun8i-h3-bananapi-m2-plus-v1.2.dtb \
 	sun8i-h3-beelink-x2.dtb \
 	sun8i-h3-libretech-all-h3-cc.dtb \
 	sun8i-h3-nanopi-m1.dtb	\
@@ -1048,6 +1049,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-h3-orangepi-pc-plus.dtb \
 	sun8i-h3-orangepi-plus.dtb \
 	sun8i-h3-orangepi-plus2e.dtb \
+	sun8i-h3-orangepi-zero-plus2.dtb \
 	sun8i-r16-bananapi-m2m.dtb \
 	sun8i-r16-nintendo-nes-classic.dtb \
 	sun8i-r16-nintendo-super-nes-classic.dtb \

arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus-v1.2.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 Chen-Yu Tsai <wens@csie.org>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-bananapi-m2-plus-v1.2.dtsi"
+
+/ {
+	model = "Banana Pi BPI-M2-Plus v1.2 H3";
+	compatible = "bananapi,bpi-m2-plus-v1.2", "allwinner,sun8i-h3";
+};

arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts

@@ -42,195 +42,9 @@
 
 /dts-v1/;
 #include "sun8i-h3.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "sunxi-bananapi-m2-plus.dtsi"
 
 / {
-	model = "Banana Pi BPI-M2-Plus";
+	model = "Banana Pi BPI-M2-Plus H3";
 	compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3";
-
-	aliases {
-		ethernet0 = &emac;
-		serial0 = &uart0;
-		serial1 = &uart1;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	connector {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_con_in: endpoint {
-				remote-endpoint = <&hdmi_out_con>;
-			};
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-
-		pwr_led {
-			label = "bananapi-m2-plus:red:pwr";
-			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
-			default-state = "on";
-		};
-	};
-
-	gpio_keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-
-		sw4 {
-			label = "power";
-			linux,code = <BTN_0>;
-			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	reg_gmac_3v3: gmac-3v3 {
-		      compatible = "regulator-fixed";
-		      regulator-name = "gmac-3v3";
-		      regulator-min-microvolt = <3300000>;
-		      regulator-max-microvolt = <3300000>;
-		      startup-delay-us = <100000>;
-		      enable-active-high;
-		      gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
-	};
-
-	wifi_pwrseq: wifi_pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
-		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-	};
-};
-
-&de {
-	status = "okay";
-};
-
-&ehci0 {
-	status = "okay";
-};
-
-&ehci1 {
-	status = "okay";
-};
-
-&ehci2 {
-	status = "okay";
-};
-
-&emac {
-	pinctrl-names = "default";
-	pinctrl-0 = <&emac_rgmii_pins>;
-	phy-supply = <&reg_gmac_3v3>;
-	phy-handle = <&ext_rgmii_phy>;
-	phy-mode = "rgmii";
-
-	status = "okay";
-};
-
-&external_mdio {
-	ext_rgmii_phy: ethernet-phy@1 {
-		compatible = "ethernet-phy-ieee802.3-c22";
-		reg = <0>;
-	};
-};
-
-&hdmi {
-	status = "okay";
-};
-
-&hdmi_out {
-	hdmi_out_con: endpoint {
-		remote-endpoint = <&hdmi_con_in>;
-	};
-};
-
-&ir {
-	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
-	status = "okay";
-};
-
-&mmc0 {
-	vmmc-supply = <&reg_vcc3v3>;
-	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
-	status = "okay";
-};
-
-&mmc1 {
-	vmmc-supply = <&reg_vcc3v3>;
-	vqmmc-supply = <&reg_vcc3v3>;
-	mmc-pwrseq = <&wifi_pwrseq>;
-	bus-width = <4>;
-	non-removable;
-	status = "okay";
-
-	brcmf: wifi@1 {
-		reg = <1>;
-		compatible = "brcm,bcm4329-fmac";
-		interrupt-parent = <&pio>;
-		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
-		interrupt-names = "host-wake";
-	};
-};
-
-&mmc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc2_8bit_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
-	vqmmc-supply = <&reg_vcc3v3>;
-	bus-width = <8>;
-	non-removable;
-	status = "okay";
-};
-
-&ohci0 {
-	status = "okay";
-};
-
-&ohci1 {
-	status = "okay";
-};
-
-&ohci2 {
-	status = "okay";
-};
-
-&reg_usb0_vbus {
-	gpio = <&pio 3 11 GPIO_ACTIVE_HIGH>; /* PD11 */
-	status = "okay";
-};
-
-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
-	status = "okay";
-};
-
-&usb_otg {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&usbphy {
-	usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
-	usb0_vbus-supply = <&reg_usb0_vbus>;
-	/* USB host VBUS is on as long as VCC-IO is on */
-	status = "okay";
 };

arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts

+/*
+ * Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
+ * Copyright (C) 2018 Diego Rondini <diego.rondini@kynetics.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "sun8i-h3.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "OrangePi Zero Plus2 H3";
+	compatible = "xunlong,orangepi-zero-plus2-h3", "allwinner,sun8i-h3";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&de {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>;	/* PL7 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};

arch/arm/boot/dts/sun8i-h3.dtsi

@@ -119,6 +119,20 @@ timer {
 			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
 	};
 
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		cma_pool: cma@4a000000 {
+			compatible = "shared-dma-pool";
+			size = <0x6000000>;
+			alloc-ranges = <0x4a000000 0x6000000>;
+			reusable;
+			linux,cma-default;
+		};
+	};
+
 	soc {
 		system-control@1c00000 {
 			compatible = "allwinner,sun8i-h3-system-control";
@@ -142,6 +156,17 @@ ve_sram: sram-section@0 {
 			};
 		};
 
+		video-codec@01c0e000 {
+			compatible = "allwinner,sun8i-h3-video-engine";
+			reg = <0x01c0e000 0x1000>;
+			clocks = <&ccu CLK_BUS_VE>, <&ccu CLK_VE>,
+				 <&ccu CLK_DRAM_VE>;
+			clock-names = "ahb", "mod", "ram";
+			resets = <&ccu RST_BUS_VE>;
+			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+			allwinner,sram = <&ve_sram 1>;
+		};
+
 		mali: gpu@1c40000 {
 			compatible = "allwinner,sun8i-h3-mali", "arm,mali-400";
 			reg = <0x01c40000 0x10000>;

arch/arm/boot/dts/sunxi-bananapi-m2-plus-v1.2.dtsi

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 Chen-Yu Tsai <wens@csie.org>
+ */
+
+#include "sunxi-bananapi-m2-plus.dtsi"
+
+/ {
+	/*
+	 * Bananapi M2+ v1.2 uses a GPIO line to change the effective
+	 * resistance on the CPU regulator's feedback pin.
+	 */
+	reg_vdd_cpux: vdd-cpux {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-cpux";
+		regulator-type = "voltage";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-ramp-delay = <50>; /* 4ms */
+		gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
+		gpios-states = <0x1>;
+		states = <1100000 0x0
+			  1300000 0x1>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};

arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi

+/*
+ * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	aliases {
+		ethernet0 = &emac;
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+
+		pwr_led {
+			label = "bananapi-m2-plus:red:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+			default-state = "on";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+
+		sw4 {
+			label = "power";
+			linux,code = <BTN_0>;
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	reg_gmac_3v3: gmac-3v3 {
+		      compatible = "regulator-fixed";
+		      regulator-name = "gmac-3v3";
+		      regulator-min-microvolt = <3300000>;
+		      regulator-max-microvolt = <3300000>;
+		      startup-delay-us = <100000>;
+		      enable-active-high;
+		      gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+	};
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir_pins_a>;
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&reg_usb0_vbus {
+	gpio = <&pio 3 11 GPIO_ACTIVE_HIGH>; /* PD11 */
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	/* USB host VBUS is on as long as VCC-IO is on */
+	status = "okay";
+};

arch/arm/boot/dts/sunxi-h3-h5.dtsi

@@ -816,7 +816,7 @@ ir: ir@1f02000 {
 			clock-names = "apb", "ir";
 			resets = <&r_ccu RST_APB0_IR>;
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
-			reg = <0x01f02000 0x40>;
+			reg = <0x01f02000 0x400>;
 			status = "disabled";
 		};
 

arch/arm64/boot/dts/allwinner/Makefile

@@ -8,6 +8,8 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-libretech-all-h3-cc.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo-plus2.dtb

arch/arm64/boot/dts/allwinner/sun50i-h5-bananapi-m2-plus-v1.2.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2018 Chen-Yu Tsai <wens@csie.org>
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+#include <arm/sunxi-bananapi-m2-plus-v1.2.dtsi>
+
+/ {
+	model = "Banana Pi BPI-M2-Plus v1.2 H5";
+	compatible = "bananapi,bpi-m2-plus-v1.2", "allwinner,sun50i-h5";
+};

arch/arm64/boot/dts/allwinner/sun50i-h5-bananapi-m2-plus.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2018 Chen-Yu Tsai <wens@csie.org>
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+#include <arm/sunxi-bananapi-m2-plus.dtsi>
+
+/ {
+	model = "Banana Pi BPI-M2-Plus H5";
+	compatible = "sinovoip,bpi-m2-plus", "allwinner,sun50i-h5";
+};

arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi

@@ -92,6 +92,49 @@ timer {
 			     <GIC_PPI 10
 				(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
 	};
+
+	soc {
+		mali: gpu@1e80000 {
+			compatible = "allwinner,sun50i-h5-mali", "arm,mali-450";
+			reg = <0x01e80000 0x30000>;
+			/*
+			 * While the datasheet lists an interrupt for the
+			 * PMU, the actual silicon does not have the PMU
+			 * block. Reads all return zero, and writes are
+			 * ignored.
+			 */
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "gp",
+					  "gpmmu",
+					  "pp",
+					  "pp0",
+					  "ppmmu0",
+					  "pp1",
+					  "ppmmu1",
+					  "pp2",
+					  "ppmmu2",
+					  "pp3",
+					  "ppmmu3",
+					  "pmu";
+			clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>;
+			clock-names = "bus", "core";
+			resets = <&ccu RST_BUS_GPU>;
+
+			assigned-clocks = <&ccu CLK_GPU>;
+			assigned-clock-rates = <384000000>;
+		};
+	};
 };
 
 &ccu {