pinctrl: generic: Add bi-directional and output-enable

Add bi-directional and output-enable pin configuration properties.

bi-directional allows to specify when a pin shall operate in input and
output mode at the same time. This is particularly useful in platforms
where input and output buffers have to be manually enabled.

output-enable is just syntactic sugar to specify that a pin shall
operate in output mode, ignoring the provided argument.
This pairs with input-enable pin configuration option.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt

@@ -247,6 +247,7 @@ bias-bus-hold		- latch weakly
 bias-pull-up		- pull up the pin
 bias-pull-down		- pull down the pin
 bias-pull-pin-default	- use pin-default pull state
+bi-directional		- pin supports simultaneous input/output operations
 drive-push-pull		- drive actively high and low
 drive-open-drain	- drive with open drain
 drive-open-source	- drive with open source
@@ -259,6 +260,7 @@ input-debounce		- debounce mode with debound time X
 power-source		- select between different power supplies
 low-power-enable	- enable low power mode
 low-power-disable	- disable low power mode
+output-enable		- enable output on pin regardless of output value
 output-low		- set the pin to output mode with low level
 output-high		- set the pin to output mode with high level
 slew-rate		- set the slew rate

drivers/pinctrl/pinconf-generic.c

@@ -35,6 +35,7 @@ static const struct pin_config_item conf_items[] = {
 	PCONFDUMP(PIN_CONFIG_BIAS_PULL_PIN_DEFAULT,
 				"input bias pull to pin specific state", NULL, false),
 	PCONFDUMP(PIN_CONFIG_BIAS_PULL_UP, "input bias pull up", NULL, false),
+	PCONFDUMP(PIN_CONFIG_BIDIRECTIONAL, "bi-directional pin operations", NULL, false),
 	PCONFDUMP(PIN_CONFIG_DRIVE_OPEN_DRAIN, "output drive open drain", NULL, false),
 	PCONFDUMP(PIN_CONFIG_DRIVE_OPEN_SOURCE, "output drive open source", NULL, false),
 	PCONFDUMP(PIN_CONFIG_DRIVE_PUSH_PULL, "output drive push pull", NULL, false),
@@ -160,6 +161,7 @@ static const struct pinconf_generic_params dt_params[] = {
 	{ "bias-pull-up", PIN_CONFIG_BIAS_PULL_UP, 1 },
 	{ "bias-pull-pin-default", PIN_CONFIG_BIAS_PULL_PIN_DEFAULT, 1 },
 	{ "bias-pull-down", PIN_CONFIG_BIAS_PULL_DOWN, 1 },
+	{ "bi-directional", PIN_CONFIG_BIDIRECTIONAL, 1 },
 	{ "drive-open-drain", PIN_CONFIG_DRIVE_OPEN_DRAIN, 0 },
 	{ "drive-open-source", PIN_CONFIG_DRIVE_OPEN_SOURCE, 0 },
 	{ "drive-push-pull", PIN_CONFIG_DRIVE_PUSH_PULL, 0 },
@@ -172,6 +174,7 @@ static const struct pinconf_generic_params dt_params[] = {
 	{ "input-schmitt-enable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 1 },
 	{ "low-power-disable", PIN_CONFIG_LOW_POWER_MODE, 0 },
 	{ "low-power-enable", PIN_CONFIG_LOW_POWER_MODE, 1 },
+	{ "output-enable", PIN_CONFIG_OUTPUT, 1, },
 	{ "output-high", PIN_CONFIG_OUTPUT, 1, },
 	{ "output-low", PIN_CONFIG_OUTPUT, 0, },
 	{ "power-source", PIN_CONFIG_POWER_SOURCE, 0 },

include/linux/pinctrl/pinconf-generic.h

@@ -42,6 +42,8 @@
  * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high
  *	impedance to VDD). If the argument is != 0 pull-up is enabled,
  *	if it is 0, pull-up is total, i.e. the pin is connected to VDD.
+ * @PIN_CONFIG_BIDIRECTIONAL: the pin will be configured to allow simultaneous
+ *	input and output operations.
  * @PIN_CONFIG_DRIVE_OPEN_DRAIN: the pin will be driven with open drain (open
  *	collector) which means it is usually wired with other output ports
  *	which are then pulled up with an external resistor. Setting this
@@ -96,6 +98,7 @@ enum pin_config_param {
 	PIN_CONFIG_BIAS_PULL_DOWN,
 	PIN_CONFIG_BIAS_PULL_PIN_DEFAULT,
 	PIN_CONFIG_BIAS_PULL_UP,
+	PIN_CONFIG_BIDIRECTIONAL,
 	PIN_CONFIG_DRIVE_OPEN_DRAIN,
 	PIN_CONFIG_DRIVE_OPEN_SOURCE,
 	PIN_CONFIG_DRIVE_PUSH_PULL,