Merge series "Enable VBUS current boost on pm8150b platforms" from Bryan...

Merge series "Enable VBUS current boost on pm8150b platforms" from Bryan O'Donoghue <bryan.odonoghue@linaro.org>:

V3:
- Drop the SoC regulator constraints for
  regulator-min-microamp
  regulator-max-microamp
  These will be applied on a per-board basis - Mark Brown

V2:
The first version of this patch set the current limit to 3 amps as was done
in downstream. Mark indicated a preference to set this on a per-system
basis instead of blitzing it, as in downstream.

Looking at what was upstream versus what was in my working tree I saw that
in fact the VBUS boost driver had been upstreamed minus accompanying DTS in
pm8150b.

So there's no need for a fixes as this driver doesn't appear to be in use.
A subsequent patchset will enable the VBUS boost for the two relevant
upstream platforms.

First thing though, is the driver + dts change.

- Use regulator_set_current_limit_regmap/regulator_get_current_limit_regmap
  with a relevant current-to-bitmap lookup.

- Add a parallel DTS entry to the pm8150b
  It looks like this was submitted upstream but not followed up on

  I've add regulator-min-microamp/regulator-max-microamp to Wesley's
  original work.

I've made sure to test that its possible to set the current to anything in
the range of 500 mA to 3 A and confirmed the output on a scope.

Once these two patches are in, I'll send out board enablement for the
sm8150-mtp and qrb5165-rb5.

https://lore.kernel.org/linux-arm-msm/8687acdb-75e9-5fc5-dd3e-9a19615676b5@linaro.org/T/#t

Bryan O'Donoghue (1):
  regulator: Add a routine to set the current limit for QCOM PMIC VBUS

Wesley Cheng (1):
  arm64: boot: dts: qcom: pm8150b: Add DTS node for PMIC VBUS booster

 arch/arm64/boot/dts/qcom/pm8150b.dtsi       |  6 ++++++
 drivers/regulator/qcom_usb_vbus-regulator.c | 12 ++++++++++++
 2 files changed, 18 insertions(+)

--
2.30.1

drivers/regulator/qcom_usb_vbus-regulator.c

@@ -16,13 +16,21 @@
 
 #define CMD_OTG				0x40
 #define OTG_EN				BIT(0)
+#define OTG_CURRENT_LIMIT_CFG		0x52
+#define OTG_CURRENT_LIMIT_MASK		GENMASK(2, 0)
 #define OTG_CFG				0x53
 #define OTG_EN_SRC_CFG			BIT(1)
 
+static const unsigned int curr_table[] = {
+	500000, 1000000, 1500000, 2000000, 2500000, 3000000,
+};
+
 static const struct regulator_ops qcom_usb_vbus_reg_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
+	.get_current_limit = regulator_get_current_limit_regmap,
+	.set_current_limit = regulator_set_current_limit_regmap,
 };
 
 static struct regulator_desc qcom_usb_vbus_rdesc = {
@@ -30,6 +38,8 @@ static struct regulator_desc qcom_usb_vbus_rdesc = {
 	.ops = &qcom_usb_vbus_reg_ops,
 	.owner = THIS_MODULE,
 	.type = REGULATOR_VOLTAGE,
+	.curr_table = curr_table,
+	.n_current_limits = ARRAY_SIZE(curr_table),
 };
 
 static int qcom_usb_vbus_regulator_probe(struct platform_device *pdev)
@@ -61,6 +71,8 @@ static int qcom_usb_vbus_regulator_probe(struct platform_device *pdev)
 
 	qcom_usb_vbus_rdesc.enable_reg = base + CMD_OTG;
 	qcom_usb_vbus_rdesc.enable_mask = OTG_EN;
+	qcom_usb_vbus_rdesc.csel_reg = base + OTG_CURRENT_LIMIT_CFG;
+	qcom_usb_vbus_rdesc.csel_mask = OTG_CURRENT_LIMIT_MASK;
 	config.dev = dev;
 	config.init_data = init_data;
 	config.of_node = dev->of_node;