Commit 8d9e53b9 authored by Chris Metcalf's avatar Chris Metcalf

tile PCI RC: use proper accessor function

Using the low-level hv_dev_pread() API makes assumptions about the
layout of datastructures in the Tilera hypervisor API; it's better to
use the gxio_XXX accessor and the pcie_trio_ports_property struct.
Signed-off-by: default avatarChris Metcalf <cmetcalf@tilera.com>
parent eafa5c8a
......@@ -91,7 +91,7 @@ static int rc_delay[TILEGX_NUM_TRIO][TILEGX_TRIO_PCIES];
TRIO_PCIE_INTFC_PORT_CONFIG__STRAP_STATE_VAL_AUTO_CONFIG_ENDPOINT_G1
/* Array of the PCIe ports configuration info obtained from the BIB. */
struct pcie_port_property pcie_ports[TILEGX_NUM_TRIO][TILEGX_TRIO_PCIES];
struct pcie_trio_ports_property pcie_ports[TILEGX_NUM_TRIO];
/* Number of configured TRIO instances. */
int num_trio_shims;
......@@ -195,10 +195,7 @@ static int tile_pcie_open(int trio_index)
#endif
/* Get the properties of the PCIe ports on this TRIO instance. */
ret = hv_dev_pread(context->fd, 0,
(HV_VirtAddr)&pcie_ports[trio_index][0],
sizeof(struct pcie_port_property) * TILEGX_TRIO_PCIES,
GXIO_TRIO_OP_GET_PORT_PROPERTY);
ret = gxio_trio_get_port_property(context, &pcie_ports[trio_index]);
if (ret < 0) {
pr_err("PCI: PCIE_GET_PORT_PROPERTY failure, error %d,"
" on TRIO %d\n", ret, trio_index);
......@@ -221,8 +218,8 @@ static int tile_pcie_open(int trio_index)
unsigned int reg_offset;
/* Ignore ports that are not specified in the BIB. */
if (!pcie_ports[trio_index][mac].allow_rc &&
!pcie_ports[trio_index][mac].allow_ep)
if (!pcie_ports[trio_index].ports[mac].allow_rc &&
!pcie_ports[trio_index].ports[mac].allow_ep)
continue;
reg_offset =
......@@ -243,7 +240,7 @@ static int tile_pcie_open(int trio_index)
*/
if (port_config.strap_state == AUTO_CONFIG_EP ||
port_config.strap_state == AUTO_CONFIG_EP_G1)
pcie_ports[trio_index][mac].allow_ep = 1;
pcie_ports[trio_index].ports[mac].allow_ep = 1;
}
}
......@@ -438,9 +435,10 @@ int __init tile_pci_init(void)
return 0;
/*
* Now determine which PCIe ports are configured to operate in RC mode.
* We look at the Board Information Block first and then see if there
* are any overriding configuration by the HW strapping pin.
* Now determine which PCIe ports are configured to operate in RC
* mode. To use a port, it must be allowed to be in RC mode by the
* Board Information Block, and the hardware strapping pins must be
* set to RC mode.
*/
for (i = 0; i < TILEGX_NUM_TRIO; i++) {
gxio_trio_context_t *context = &trio_contexts[i];
......@@ -449,7 +447,7 @@ int __init tile_pci_init(void)
continue;
for (j = 0; j < TILEGX_TRIO_PCIES; j++) {
if (pcie_ports[i][j].allow_rc &&
if (pcie_ports[i].ports[j].allow_rc &&
strapped_for_rc(context, j)) {
pcie_rc[i][j] = 1;
num_rc_controllers++;
......@@ -736,7 +734,7 @@ int __init pcibios_init(void)
__gxio_mmio_read(trio_context->mmio_base_mac +
reg_offset);
if (!port_status.dl_up) {
if (pcie_ports[trio_index][mac].removable) {
if (pcie_ports[trio_index].ports[mac].removable) {
pr_info("PCI: link is down, MAC %d on TRIO %d\n",
mac, trio_index);
pr_info("This is expected if no PCIe card"
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment