Commit 8effc4a6 authored by Michael Hennerich's avatar Michael Hennerich Committed by Mike Frysinger

Blackfin: ad7160eval: new board port

Signed-off-by: default avatarMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: default avatarMike Frysinger <vapier@gentoo.org>
parent 27e9f0b4
......@@ -356,7 +356,7 @@ config MEM_MT48LC8M32B2B5_7
config MEM_MT48LC32M16A2TG_75
bool
depends on (BFIN527_EZKIT || BFIN527_EZKIT_V2 || BFIN532_IP0X || BLACKSTAMP)
depends on (BFIN527_EZKIT || BFIN527_EZKIT_V2 || BFIN532_IP0X || BLACKSTAMP || BFIN527_AD7160EVAL)
default y
config MEM_MT48H32M16LFCJ_75
......@@ -426,6 +426,7 @@ config CLKIN_HZ
default "25000000" # most people use this
default "27000000" if BFIN533_EZKIT
default "30000000" if BFIN561_EZKIT
default "24000000" if BFIN527_AD7160EVAL
help
The frequency of CLKIN crystal oscillator on the board in Hz.
Warning: This value should match the crystal on the board. Otherwise,
......@@ -463,6 +464,7 @@ config VCO_MULT
default "20" if (BFIN537_BLUETECHNIX_CM_E || BFIN537_BLUETECHNIX_CM_U || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
default "20" if BFIN561_EZKIT
default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN518F_EZBRD)
default "25" if BFIN527_AD7160EVAL
help
This controls the frequency of the on-chip PLL. This can be between 1 and 64.
PLL Frequency = (Crystal Frequency) * (this setting)
......
CONFIG_EXPERIMENTAL=y
CONFIG_SYSVIPC=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_BLK_DEV_INITRD=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_EMBEDDED=y
# CONFIG_ELF_CORE is not set
# CONFIG_AIO is not set
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_IOSCHED_DEADLINE is not set
CONFIG_PREEMPT=y
CONFIG_BF527=y
CONFIG_BF_REV_0_2=y
CONFIG_IRQ_TWI=7
CONFIG_IRQ_PORTH_INTA=7
CONFIG_IRQ_PORTH_INTB=7
CONFIG_BFIN527_AD7160EVAL=y
CONFIG_BF527_SPORT0_PORTF=y
CONFIG_BF527_UART1_PORTG=y
CONFIG_IRQ_USB_INT0=11
CONFIG_IRQ_USB_INT1=11
CONFIG_IRQ_USB_INT2=11
CONFIG_IRQ_USB_DMA=11
CONFIG_CMDLINE_BOOL=y
CONFIG_CMDLINE="bootargs=root=/dev/mtdblock0 rw clkin_hz=24000000 earlyprintk=serial,uart0,57600 console=tty0 console=ttyBF0,57600"
CONFIG_CLKIN_HZ=24000000
CONFIG_HZ_300=y
# CONFIG_CYCLES_CLOCKSOURCE is not set
CONFIG_IP_CHECKSUM_L1=y
CONFIG_SYSCALL_TAB_L1=y
CONFIG_CPLB_SWITCH_TAB_L1=y
CONFIG_BFIN_GPTIMERS=y
CONFIG_C_CDPRIO=y
CONFIG_BANK_1=0x5554
CONFIG_BANK_3=0xFFC0
CONFIG_BINFMT_FLAT=y
CONFIG_BINFMT_ZFLAT=y
CONFIG_NET=y
CONFIG_UNIX=y
# CONFIG_WIRELESS is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
# CONFIG_MISC_DEVICES is not set
# CONFIG_INPUT_MOUSEDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_AD7160=y
CONFIG_TOUCHSCREEN_AD7160_FW=y
# CONFIG_SERIO is not set
# CONFIG_BFIN_DMA_INTERFACE is not set
# CONFIG_DEVKMEM is not set
CONFIG_SERIAL_BFIN=y
CONFIG_SERIAL_BFIN_CONSOLE=y
CONFIG_SERIAL_BFIN_UART0=y
# CONFIG_LEGACY_PTYS is not set
# CONFIG_BFIN_OTP is not set
# CONFIG_HW_RANDOM is not set
CONFIG_I2C=y
# CONFIG_I2C_HELPER_AUTO is not set
CONFIG_I2C_ALGOBIT=y
CONFIG_I2C_BLACKFIN_TWI=y
CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=400
CONFIG_SPI=y
CONFIG_SPI_BFIN=y
CONFIG_GPIOLIB=y
CONFIG_GPIO_SYSFS=y
# CONFIG_HWMON is not set
CONFIG_FB=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
# CONFIG_LOGO_LINUX_CLUT224 is not set
# CONFIG_LOGO_BLACKFIN_VGA16 is not set
# CONFIG_HID_SUPPORT is not set
CONFIG_USB_MUSB_HDRC=y
CONFIG_USB_GADGET_MUSB_HDRC=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_VBUS_DRAW=500
CONFIG_USB_G_SERIAL=y
CONFIG_MMC=y
CONFIG_MMC_SPI=y
CONFIG_EXT2_FS=y
# CONFIG_DNOTIFY is not set
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
CONFIG_DEBUG_KERNEL=y
CONFIG_DETECT_HUNG_TASK=y
# CONFIG_SCHED_DEBUG is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
# CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE is not set
CONFIG_EARLY_PRINTK=y
CONFIG_CPLB_INFO=y
CONFIG_SECURITY=y
CONFIG_CRC_CCITT=m
......@@ -24,4 +24,9 @@ config BFIN526_EZBRD
help
BF526-EZBRD/EZKIT Lite board support.
config BFIN527_AD7160EVAL
bool "BF527-AD7160-EVAL"
help
BF527-AD7160-EVAL board support.
endchoice
......@@ -6,3 +6,4 @@ obj-$(CONFIG_BFIN527_EZKIT) += ezkit.o
obj-$(CONFIG_BFIN527_EZKIT_V2) += ezkit.o
obj-$(CONFIG_BFIN527_BLUETECHNIX_CM) += cm_bf527.o
obj-$(CONFIG_BFIN526_EZBRD) += ezbrd.o
obj-$(CONFIG_BFIN527_AD7160EVAL) += ad7160eval.o
This diff is collapsed.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment