Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC fixes from Arnd Bergmann:
 "A couple of minor fixes only for now

   - fix for incorrect DMA channels on Renesas R-Car

   - Broadcom bcm2835 error handling fixes

   - Kconfig dependency fixes for bcm2835 and davinci

   - CPU idle wakeup fix for i.MX6

   - MMC regression on Tegra186

   - fix incorrect phy settings on one imx board"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  arm64: tegra: Disable CQE Support for SDMMC4 on Tegra186
  ARM: dts: nomadik: Fix polarity of SPI CS
  ARM: davinci: fix build failure with allnoconfig
  ARM: imx_v4_v5_defconfig: enable PWM driver
  ARM: imx_v6_v7_defconfig: continue compiling the pwm driver
  ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch
  ARM: dts: imx6qdl: Fix typo in imx6qdl-icore-rqs.dtsi
  ARM: dts: imx6ull: Use the correct style for SPDX License Identifier
  ARM: dts: pfla02: increase phy reset duration
  ARM: imx6q: cpuidle: fix bug that CPU might not wake up at expected time
  ARM: imx51: fix a leaked reference by adding missing of_node_put
  ARM: dts: imx6dl-yapp4: Use rgmii-id phy mode on the cpu port
  arm64: bcm2835: Add missing dependency on MFD_CORE.
  ARM: dts: bcm283x: Fix hdmi hpd gpio pull
  soc: bcm: bcm2835-pm: Fix error paths of initialization.
  soc: bcm: bcm2835-pm: Fix PM_IMAGE_PERI power domain support.
  arm64: dts: renesas: r8a774c0: Fix SCIF5 DMA channels
  arm64: dts: renesas: r8a77990: Fix SCIF5 DMA channels

arch/arm/Kconfig

@@ -596,6 +596,7 @@ config ARCH_DAVINCI
 	select HAVE_IDE
 	select PM_GENERIC_DOMAINS if PM
 	select PM_GENERIC_DOMAINS_OF if PM && OF
+	select REGMAP_MMIO
 	select RESET_CONTROLLER
 	select SPARSE_IRQ
 	select USE_OF

arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts

@@ -93,7 +93,7 @@ i2s_alt2: i2s_alt2 {
 };
 
 &hdmi {
-	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
 };
 
 &pwm {

arch/arm/boot/dts/imx6dl-yapp4-common.dtsi

@@ -114,9 +114,9 @@ phy_port3: phy@2 {
 			reg = <2>;
 		};
 
-		switch@0 {
+		switch@10 {
 			compatible = "qca,qca8334";
-			reg = <0>;
+			reg = <10>;
 
 			switch_ports: ports {
 				#address-cells = <1>;
@@ -125,7 +125,7 @@ switch_ports: ports {
 				ethphy0: port@0 {
 					reg = <0>;
 					label = "cpu";
-					phy-mode = "rgmii";
+					phy-mode = "rgmii-id";
 					ethernet = <&fec>;
 
 					fixed-link {

arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi

@@ -264,7 +264,7 @@ &usdhc3 {
 	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
 	vmcc-supply = <&reg_sd3_vmmc>;
 	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
-	bus-witdh = <4>;
+	bus-width = <4>;
 	no-1-8-v;
 	status = "okay";
 };
@@ -275,7 +275,7 @@ &usdhc4 {
 	pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
 	pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
 	vmcc-supply = <&reg_sd4_vmmc>;
-	bus-witdh = <8>;
+	bus-width = <8>;
 	no-1-8-v;
 	non-removable;
 	status = "okay";

arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi

@@ -91,6 +91,7 @@ &fec {
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-handle = <&ethphy>;
 	phy-mode = "rgmii";
+	phy-reset-duration = <10>; /* in msecs */
 	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
 	phy-supply = <&vdd_eth_io_reg>;
 	status = "disabled";

arch/arm/boot/dts/imx6ull-pinfunc-snvs.h

-// SPDX-License-Identifier: GPL-2.0
+/* SPDX-License-Identifier: GPL-2.0 */
 /*
  * Copyright (C) 2016 Freescale Semiconductor, Inc.
  * Copyright (C) 2017 NXP

arch/arm/boot/dts/ste-nomadik-nhk15.dts

@@ -213,12 +213,13 @@ spi {
 		gpio-sck = <&gpio0 5 GPIO_ACTIVE_HIGH>;
 		gpio-mosi = <&gpio0 4 GPIO_ACTIVE_HIGH>;
 		/*
-		 * It's not actually active high, but the frameworks assume
-		 * the polarity of the passed-in GPIO is "normal" (active
-		 * high) then actively drives the line low to select the
-		 * chip.
+		 * This chipselect is active high. Just setting the flags
+		 * to GPIO_ACTIVE_HIGH is not enough for the SPI DT bindings,
+		 * it will be ignored, only the special "spi-cs-high" flag
+		 * really counts.
 		 */
 		cs-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+		spi-cs-high;
 		num-chipselects = <1>;
 
 		/*

arch/arm/configs/imx_v4_v5_defconfig

@@ -170,6 +170,9 @@ CONFIG_IMX_SDMA=y
 # CONFIG_IOMMU_SUPPORT is not set
 CONFIG_IIO=y
 CONFIG_FSL_MX25_ADC=y
+CONFIG_PWM=y
+CONFIG_PWM_IMX1=y
+CONFIG_PWM_IMX27=y
 CONFIG_EXT4_FS=y
 # CONFIG_DNOTIFY is not set
 CONFIG_VFAT_FS=y

arch/arm/configs/imx_v6_v7_defconfig

@@ -398,7 +398,7 @@ CONFIG_MAG3110=y
 CONFIG_MPL3115=y
 CONFIG_PWM=y
 CONFIG_PWM_FSL_FTM=y
-CONFIG_PWM_IMX=y
+CONFIG_PWM_IMX27=y
 CONFIG_NVMEM_IMX_OCOTP=y
 CONFIG_NVMEM_VF610_OCOTP=y
 CONFIG_TEE=y

arch/arm/mach-imx/cpuidle-imx6q.c

@@ -16,30 +16,23 @@
 #include "cpuidle.h"
 #include "hardware.h"
 
-static atomic_t master = ATOMIC_INIT(0);
-static DEFINE_SPINLOCK(master_lock);
+static int num_idle_cpus = 0;
+static DEFINE_SPINLOCK(cpuidle_lock);
 
 static int imx6q_enter_wait(struct cpuidle_device *dev,
 			    struct cpuidle_driver *drv, int index)
 {
-	if (atomic_inc_return(&master) == num_online_cpus()) {
-		/*
-		 * With this lock, we prevent other cpu to exit and enter
-		 * this function again and become the master.
-		 */
-		if (!spin_trylock(&master_lock))
-			goto idle;
+	spin_lock(&cpuidle_lock);
+	if (++num_idle_cpus == num_online_cpus())
 		imx6_set_lpm(WAIT_UNCLOCKED);
-		cpu_do_idle();
-		imx6_set_lpm(WAIT_CLOCKED);
-		spin_unlock(&master_lock);
-		goto done;
-	}
+	spin_unlock(&cpuidle_lock);
 
-idle:
 	cpu_do_idle();
-done:
-	atomic_dec(&master);
+
+	spin_lock(&cpuidle_lock);
+	if (num_idle_cpus-- == num_online_cpus())
+		imx6_set_lpm(WAIT_CLOCKED);
+	spin_unlock(&cpuidle_lock);
 
 	return index;
 }

arch/arm/mach-imx/mach-imx51.c

@@ -59,6 +59,7 @@ static void __init imx51_m4if_setup(void)
 		return;
 
 	m4if_base = of_iomap(np, 0);
+	of_node_put(np);
 	if (!m4if_base) {
 		pr_err("Unable to map M4IF registers\n");
 		return;

arch/arm64/Kconfig.platforms

@@ -27,6 +27,7 @@ config ARCH_BCM2835
 	bool "Broadcom BCM2835 family"
 	select TIMER_OF
 	select GPIOLIB
+	select MFD_CORE
 	select PINCTRL
 	select PINCTRL_BCM2835
 	select ARM_AMBA

arch/arm64/boot/dts/nvidia/tegra186.dtsi

@@ -321,7 +321,6 @@ sdmmc4: sdhci@3460000 {
 		nvidia,default-trim = <0x9>;
 		nvidia,dqs-trim = <63>;
 		mmc-hs400-1_8v;
-		supports-cqe;
 		status = "disabled";
 	};
 

arch/arm64/boot/dts/renesas/r8a774c0.dtsi

@@ -2,7 +2,7 @@
 /*
  * Device Tree Source for the RZ/G2E (R8A774C0) SoC
  *
- * Copyright (C) 2018 Renesas Electronics Corp.
+ * Copyright (C) 2018-2019 Renesas Electronics Corp.
  */
 
 #include <dt-bindings/clock/r8a774c0-cpg-mssr.h>
@@ -1150,9 +1150,8 @@ scif5: serial@e6f30000 {
 				 <&cpg CPG_CORE R8A774C0_CLK_S3D1C>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
-			dmas = <&dmac1 0x5b>, <&dmac1 0x5a>,
-			       <&dmac2 0x5b>, <&dmac2 0x5a>;
-			dma-names = "tx", "rx", "tx", "rx";
+			dmas = <&dmac0 0x5b>, <&dmac0 0x5a>;
+			dma-names = "tx", "rx";
 			power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>;
 			resets = <&cpg 202>;
 			status = "disabled";

arch/arm64/boot/dts/renesas/r8a77990.dtsi

@@ -2,7 +2,7 @@
 /*
  * Device Tree Source for the R-Car E3 (R8A77990) SoC
  *
- * Copyright (C) 2018 Renesas Electronics Corp.
+ * Copyright (C) 2018-2019 Renesas Electronics Corp.
  */
 
 #include <dt-bindings/clock/r8a77990-cpg-mssr.h>
@@ -1067,9 +1067,8 @@ scif5: serial@e6f30000 {
 				 <&cpg CPG_CORE R8A77990_CLK_S3D1C>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
-			dmas = <&dmac1 0x5b>, <&dmac1 0x5a>,
-			       <&dmac2 0x5b>, <&dmac2 0x5a>;
-			dma-names = "tx", "rx", "tx", "rx";
+			dmas = <&dmac0 0x5b>, <&dmac0 0x5a>;
+			dma-names = "tx", "rx";
 			power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
 			resets = <&cpg 202>;
 			status = "disabled";

drivers/soc/bcm/bcm2835-power.c

@@ -150,7 +150,12 @@ struct bcm2835_power {
 
 static int bcm2835_asb_enable(struct bcm2835_power *power, u32 reg)
 {
-	u64 start = ktime_get_ns();
+	u64 start;
+
+	if (!reg)
+		return 0;
+
+	start = ktime_get_ns();
 
 	/* Enable the module's async AXI bridges. */
 	ASB_WRITE(reg, ASB_READ(reg) & ~ASB_REQ_STOP);
@@ -165,7 +170,12 @@ static int bcm2835_asb_enable(struct bcm2835_power *power, u32 reg)
 
 static int bcm2835_asb_disable(struct bcm2835_power *power, u32 reg)
 {
-	u64 start = ktime_get_ns();
+	u64 start;
+
+	if (!reg)
+		return 0;
+
+	start = ktime_get_ns();
 
 	/* Enable the module's async AXI bridges. */
 	ASB_WRITE(reg, ASB_READ(reg) | ASB_REQ_STOP);
@@ -475,7 +485,7 @@ static int bcm2835_power_pd_power_off(struct generic_pm_domain *domain)
 	}
 }
 
-static void
+static int
 bcm2835_init_power_domain(struct bcm2835_power *power,
 			  int pd_xlate_index, const char *name)
 {
@@ -483,6 +493,17 @@ bcm2835_init_power_domain(struct bcm2835_power *power,
 	struct bcm2835_power_domain *dom = &power->domains[pd_xlate_index];
 
 	dom->clk = devm_clk_get(dev->parent, name);
+	if (IS_ERR(dom->clk)) {
+		int ret = PTR_ERR(dom->clk);
+
+		if (ret == -EPROBE_DEFER)
+			return ret;
+
+		/* Some domains don't have a clk, so make sure that we
+		 * don't deref an error pointer later.
+		 */
+		dom->clk = NULL;
+	}
 
 	dom->base.name = name;
 	dom->base.power_on = bcm2835_power_pd_power_on;
@@ -495,6 +516,8 @@ bcm2835_init_power_domain(struct bcm2835_power *power,
 	pm_genpd_init(&dom->base, NULL, true);
 
 	power->pd_xlate.domains[pd_xlate_index] = &dom->base;
+
+	return 0;
 }
 
 /** bcm2835_reset_reset - Resets a block that has a reset line in the
@@ -592,7 +615,7 @@ static int bcm2835_power_probe(struct platform_device *pdev)
 		{ BCM2835_POWER_DOMAIN_IMAGE_PERI, BCM2835_POWER_DOMAIN_CAM0 },
 		{ BCM2835_POWER_DOMAIN_IMAGE_PERI, BCM2835_POWER_DOMAIN_CAM1 },
 	};
-	int ret, i;
+	int ret = 0, i;
 	u32 id;
 
 	power = devm_kzalloc(dev, sizeof(*power), GFP_KERNEL);
@@ -619,8 +642,11 @@ static int bcm2835_power_probe(struct platform_device *pdev)
 
 	power->pd_xlate.num_domains = ARRAY_SIZE(power_domain_names);
 
-	for (i = 0; i < ARRAY_SIZE(power_domain_names); i++)
-		bcm2835_init_power_domain(power, i, power_domain_names[i]);
+	for (i = 0; i < ARRAY_SIZE(power_domain_names); i++) {
+		ret = bcm2835_init_power_domain(power, i, power_domain_names[i]);
+		if (ret)
+			goto fail;
+	}
 
 	for (i = 0; i < ARRAY_SIZE(domain_deps); i++) {
 		pm_genpd_add_subdomain(&power->domains[domain_deps[i].parent].base,
@@ -634,12 +660,21 @@ static int bcm2835_power_probe(struct platform_device *pdev)
 
 	ret = devm_reset_controller_register(dev, &power->reset);
 	if (ret)
-		return ret;
+		goto fail;
 
 	of_genpd_add_provider_onecell(dev->parent->of_node, &power->pd_xlate);
 
 	dev_info(dev, "Broadcom BCM2835 power domains driver");
 	return 0;
+
+fail:
+	for (i = 0; i < ARRAY_SIZE(power_domain_names); i++) {
+		struct generic_pm_domain *dom = &power->domains[i].base;
+
+		if (dom->name)
+			pm_genpd_remove(dom);
+	}
+	return ret;
 }
 
 static int bcm2835_power_remove(struct platform_device *pdev)