Commit 990cbca0 authored by Takashi Iwai's avatar Takashi Iwai

Merge tag 'asoc-fix-v6.3-rc7' of...

Merge tag 'asoc-fix-v6.3-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v6.3

A few remaining small fixes for v6.3, all small driver specific ones.
parents bc66b591 86a24e99
......@@ -31,7 +31,7 @@ static int max98373_dac_event(struct snd_soc_dapm_widget *w,
MAX98373_GLOBAL_EN_MASK, 1);
usleep_range(30000, 31000);
break;
case SND_SOC_DAPM_POST_PMD:
case SND_SOC_DAPM_PRE_PMD:
regmap_update_bits(max98373->regmap,
MAX98373_R20FF_GLOBAL_SHDN,
MAX98373_GLOBAL_EN_MASK, 0);
......@@ -64,7 +64,7 @@ static const struct snd_kcontrol_new max98373_spkfb_control =
static const struct snd_soc_dapm_widget max98373_dapm_widgets[] = {
SND_SOC_DAPM_DAC_E("Amp Enable", "HiFi Playback",
MAX98373_R202B_PCM_RX_EN, 0, 0, max98373_dac_event,
SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_POST_PMD),
SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),
SND_SOC_DAPM_MUX("DAI Sel Mux", SND_SOC_NOPM, 0, 0,
&max98373_dai_controls),
SND_SOC_DAPM_OUTPUT("BE_OUT"),
......
......@@ -209,14 +209,19 @@ static int fsl_asrc_dma_hw_params(struct snd_soc_component *component,
be_chan = soc_component_to_pcm(component_be)->chan[substream->stream];
tmp_chan = be_chan;
}
if (!tmp_chan)
tmp_chan = dma_request_slave_channel(dev_be, tx ? "tx" : "rx");
if (!tmp_chan) {
tmp_chan = dma_request_chan(dev_be, tx ? "tx" : "rx");
if (IS_ERR(tmp_chan)) {
dev_err(dev, "failed to request DMA channel for Back-End\n");
return -EINVAL;
}
}
/*
* An EDMA DEV_TO_DEV channel is fixed and bound with DMA event of each
* peripheral, unlike SDMA channel that is allocated dynamically. So no
* need to configure dma_request and dma_request2, but get dma_chan of
* Back-End device directly via dma_request_slave_channel.
* Back-End device directly via dma_request_chan.
*/
if (!asrc->use_edma) {
/* Get DMA request of Back-End */
......
......@@ -1546,7 +1546,7 @@ static const struct fsl_sai_soc_data fsl_sai_imx8qm_data = {
.use_imx_pcm = true,
.use_edma = true,
.fifo_depth = 64,
.pins = 1,
.pins = 4,
.reg_offset = 0,
.mclk0_is_mclk1 = false,
.flags = 0,
......
......@@ -1806,10 +1806,12 @@ static int sof_ipc4_route_setup(struct snd_sof_dev *sdev, struct snd_sof_route *
int ret;
if (!src_fw_module || !sink_fw_module) {
/* The NULL module will print as "(efault)" */
dev_err(sdev->dev, "source %s or sink %s widget weren't set up properly\n",
src_fw_module->man4_module_entry.name,
sink_fw_module->man4_module_entry.name);
dev_err(sdev->dev,
"cannot bind %s -> %s, no firmware module for: %s%s\n",
src_widget->widget->name, sink_widget->widget->name,
src_fw_module ? "" : " source",
sink_fw_module ? "" : " sink");
return -ENODEV;
}
......
......@@ -183,6 +183,7 @@ static int sof_suspend(struct device *dev, bool runtime_suspend)
const struct sof_ipc_tplg_ops *tplg_ops = sof_ipc_get_ops(sdev, tplg);
pm_message_t pm_state;
u32 target_state = snd_sof_dsp_power_target(sdev);
u32 old_state = sdev->dsp_power_state.state;
int ret;
/* do nothing if dsp suspend callback is not set */
......@@ -192,7 +193,12 @@ static int sof_suspend(struct device *dev, bool runtime_suspend)
if (runtime_suspend && !sof_ops(sdev)->runtime_suspend)
return 0;
if (tplg_ops && tplg_ops->tear_down_all_pipelines)
/* we need to tear down pipelines only if the DSP hardware is
* active, which happens for PCI devices. if the device is
* suspended, it is brought back to full power and then
* suspended again
*/
if (tplg_ops && tplg_ops->tear_down_all_pipelines && (old_state == SOF_DSP_PM_D0))
tplg_ops->tear_down_all_pipelines(sdev, false);
if (sdev->fw_state != SOF_FW_BOOT_COMPLETE)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment