ARM: EXYNOS: Move arm core power down clock to exynos5250 common clock

Now with common clock support added for exynos5250 it is necessary to
move this code to exynos5250 common clock driver as clock registers
should be handled there. This change is tested in exynos5250 based
arndale platform.

Cc: Abhilash Kesavan <a.kesavan@samsung.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsugn.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
[t.figa: Rebased onto current kernel sources.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

arch/arm/mach-exynos/cpuidle.c

@@ -41,25 +41,6 @@
 
 #define S5P_CHECK_AFTR		0xFCBA0D10
 
-#define EXYNOS5_PWR_CTRL1			(S5P_VA_CMU + 0x01020)
-#define EXYNOS5_PWR_CTRL2			(S5P_VA_CMU + 0x01024)
-
-#define PWR_CTRL1_CORE2_DOWN_RATIO		(7 << 28)
-#define PWR_CTRL1_CORE1_DOWN_RATIO		(7 << 16)
-#define PWR_CTRL1_DIV2_DOWN_EN			(1 << 9)
-#define PWR_CTRL1_DIV1_DOWN_EN			(1 << 8)
-#define PWR_CTRL1_USE_CORE1_WFE			(1 << 5)
-#define PWR_CTRL1_USE_CORE0_WFE			(1 << 4)
-#define PWR_CTRL1_USE_CORE1_WFI			(1 << 1)
-#define PWR_CTRL1_USE_CORE0_WFI			(1 << 0)
-
-#define PWR_CTRL2_DIV2_UP_EN			(1 << 25)
-#define PWR_CTRL2_DIV1_UP_EN			(1 << 24)
-#define PWR_CTRL2_DUR_STANDBY2_VAL		(1 << 16)
-#define PWR_CTRL2_DUR_STANDBY1_VAL		(1 << 8)
-#define PWR_CTRL2_CORE2_UP_RATIO		(1 << 4)
-#define PWR_CTRL2_CORE1_UP_RATIO		(1 << 0)
-
 static int exynos4_enter_lowpower(struct cpuidle_device *dev,
 				struct cpuidle_driver *drv,
 				int index);
@@ -182,46 +163,11 @@ static int exynos4_enter_lowpower(struct cpuidle_device *dev,
 		return exynos4_enter_core0_aftr(dev, drv, new_index);
 }
 
-static void __init exynos5_core_down_clk(void)
-{
-	unsigned int tmp;
-
-	/*
-	 * Enable arm clock down (in idle) and set arm divider
-	 * ratios in WFI/WFE state.
-	 */
-	tmp = PWR_CTRL1_CORE2_DOWN_RATIO | \
-	      PWR_CTRL1_CORE1_DOWN_RATIO | \
-	      PWR_CTRL1_DIV2_DOWN_EN	 | \
-	      PWR_CTRL1_DIV1_DOWN_EN	 | \
-	      PWR_CTRL1_USE_CORE1_WFE	 | \
-	      PWR_CTRL1_USE_CORE0_WFE	 | \
-	      PWR_CTRL1_USE_CORE1_WFI	 | \
-	      PWR_CTRL1_USE_CORE0_WFI;
-	__raw_writel(tmp, EXYNOS5_PWR_CTRL1);
-
-	/*
-	 * Enable arm clock up (on exiting idle). Set arm divider
-	 * ratios when not in idle along with the standby duration
-	 * ratios.
-	 */
-	tmp = PWR_CTRL2_DIV2_UP_EN	 | \
-	      PWR_CTRL2_DIV1_UP_EN	 | \
-	      PWR_CTRL2_DUR_STANDBY2_VAL | \
-	      PWR_CTRL2_DUR_STANDBY1_VAL | \
-	      PWR_CTRL2_CORE2_UP_RATIO	 | \
-	      PWR_CTRL2_CORE1_UP_RATIO;
-	__raw_writel(tmp, EXYNOS5_PWR_CTRL2);
-}
-
 static int exynos_cpuidle_probe(struct platform_device *pdev)
 {
 	int cpu_id, ret;
 	struct cpuidle_device *device;
 
-	if (soc_is_exynos5250())
-		exynos5_core_down_clk();
-
 	if (soc_is_exynos5440())
 		exynos4_idle_driver.state_count = 1;
 

drivers/clk/samsung/clk-exynos5250.c

@@ -24,6 +24,8 @@
 #define APLL_CON0		0x100
 #define SRC_CPU			0x200
 #define DIV_CPU0		0x500
+#define PWR_CTRL1		0x1020
+#define PWR_CTRL2		0x1024
 #define MPLL_LOCK		0x4000
 #define MPLL_CON0		0x4100
 #define SRC_CORE1		0x4204
@@ -82,6 +84,23 @@
 #define SRC_CDREX		0x20200
 #define PLL_DIV2_SEL		0x20a24
 
+/*Below definitions are used for PWR_CTRL settings*/
+#define PWR_CTRL1_CORE2_DOWN_RATIO		(7 << 28)
+#define PWR_CTRL1_CORE1_DOWN_RATIO		(7 << 16)
+#define PWR_CTRL1_DIV2_DOWN_EN			(1 << 9)
+#define PWR_CTRL1_DIV1_DOWN_EN			(1 << 8)
+#define PWR_CTRL1_USE_CORE1_WFE			(1 << 5)
+#define PWR_CTRL1_USE_CORE0_WFE			(1 << 4)
+#define PWR_CTRL1_USE_CORE1_WFI			(1 << 1)
+#define PWR_CTRL1_USE_CORE0_WFI			(1 << 0)
+
+#define PWR_CTRL2_DIV2_UP_EN			(1 << 25)
+#define PWR_CTRL2_DIV1_UP_EN			(1 << 24)
+#define PWR_CTRL2_DUR_STANDBY2_VAL		(1 << 16)
+#define PWR_CTRL2_DUR_STANDBY1_VAL		(1 << 8)
+#define PWR_CTRL2_CORE2_UP_RATIO		(1 << 4)
+#define PWR_CTRL2_CORE1_UP_RATIO		(1 << 0)
+
 /* list of PLLs to be registered */
 enum exynos5250_plls {
 	apll, mpll, cpll, epll, vpll, gpll, bpll,
@@ -100,6 +119,8 @@ static struct samsung_clk_reg_dump *exynos5250_save;
 static unsigned long exynos5250_clk_regs[] __initdata = {
 	SRC_CPU,
 	DIV_CPU0,
+	PWR_CTRL1,
+	PWR_CTRL2,
 	SRC_CORE1,
 	SRC_TOP0,
 	SRC_TOP1,
@@ -701,6 +722,7 @@ static struct of_device_id ext_clk_match[] __initdata = {
 static void __init exynos5250_clk_init(struct device_node *np)
 {
 	struct samsung_clk_provider *ctx;
+	unsigned int tmp;
 
 	if (np) {
 		reg_base = of_iomap(np, 0);
@@ -741,6 +763,26 @@ static void __init exynos5250_clk_init(struct device_node *np)
 	samsung_clk_register_gate(ctx, exynos5250_gate_clks,
 			ARRAY_SIZE(exynos5250_gate_clks));
 
+	/*
+	 * Enable arm clock down (in idle) and set arm divider
+	 * ratios in WFI/WFE state.
+	 */
+	tmp = (PWR_CTRL1_CORE2_DOWN_RATIO | PWR_CTRL1_CORE1_DOWN_RATIO |
+		PWR_CTRL1_DIV2_DOWN_EN | PWR_CTRL1_DIV1_DOWN_EN |
+		PWR_CTRL1_USE_CORE1_WFE | PWR_CTRL1_USE_CORE0_WFE |
+		PWR_CTRL1_USE_CORE1_WFI | PWR_CTRL1_USE_CORE0_WFI);
+	__raw_writel(tmp, reg_base + PWR_CTRL1);
+
+	/*
+	 * Enable arm clock up (on exiting idle). Set arm divider
+	 * ratios when not in idle along with the standby duration
+	 * ratios.
+	 */
+	tmp = (PWR_CTRL2_DIV2_UP_EN | PWR_CTRL2_DIV1_UP_EN |
+		PWR_CTRL2_DUR_STANDBY2_VAL | PWR_CTRL2_DUR_STANDBY1_VAL |
+		PWR_CTRL2_CORE2_UP_RATIO | PWR_CTRL2_CORE1_UP_RATIO);
+	__raw_writel(tmp, reg_base + PWR_CTRL2);
+
 	exynos5250_clk_sleep_init();
 
 	pr_info("Exynos5250: clock setup completed, armclk=%ld\n",