Merge tag 'davinci-for-v4.9/dts' of...

Merge tag 'davinci-for-v4.9/dts' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt

Pull "DaVinci DA850 device-tree enhancements include" from Sekhar Nori:

- Support for new board OMAP-L138 LCDK
- Add AEMIF node on DA850 EVM and use it for NAND
- Audio support for LCDK
- Cleanups for PWM and UART

* tag 'davinci-for-v4.9/dts' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  ARM: dts: da850-lcdk: Audio support via simple-card
  ARM: dts: da850,da850-evm: Add an aemif node and use it for the NAND
  ARM: dts: da850: Add basic DTS for the LCDK
  ARM: dts: da850: Add missing pin muxing for the UARTs
  ARM: dts: da850: Add new ECAP and EPWM bindings

Documentation/devicetree/bindings/arm/davinci.txt

@@ -5,6 +5,10 @@ DA850/OMAP-L138/AM18x Evaluation Module (EVM) board
 Required root node properties:
     - compatible = "ti,da850-evm", "ti,da850";
 
+DA850/OMAP-L138/AM18x L138/C6748 Development Kit (LCDK) board
+Required root node properties:
+    - compatible = "ti,da850-lcdk", "ti,da850";
+
 EnBW AM1808 based CMC board
 Required root node properties:
     - compatible = "enbw,cmc", "ti,da850;

arch/arm/boot/dts/Makefile

@@ -120,6 +120,7 @@ dtb-$(CONFIG_ARCH_BRCMSTB) += \
 dtb-$(CONFIG_ARCH_CLPS711X) += \
 	ep7211-edb7211.dtb
 dtb-$(CONFIG_ARCH_DAVINCI) += \
+	da850-lcdk.dtb \
 	da850-enbw-cmc.dtb \
 	da850-evm.dtb
 dtb-$(CONFIG_ARCH_DIGICOLOR) += \

arch/arm/boot/dts/da850-evm.dts

@@ -29,6 +29,20 @@ mcasp0_pins: pinmux_mcasp0_pins {
 					0x04 0x00011000 0x000ff000
 				>;
 			};
+			nand_pins: nand_pins {
+				pinctrl-single,bits = <
+					/* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[4], EMA_CS[3] */
+					0x1c 0x10110110  0xf0ff0ff0
+					/*
+					 * EMA_D[0], EMA_D[1], EMA_D[2],
+					 * EMA_D[3], EMA_D[4], EMA_D[5],
+					 * EMA_D[6], EMA_D[7]
+					 */
+					0x24 0x11111111  0xffffffff
+					/* EMA_A[1], EMA_A[2] */
+					0x30 0x01100000  0x0ff00000
+				>;
+			};
 		};
 		serial0: serial@42000 {
 			status = "okay";
@@ -131,11 +145,6 @@ gpio: gpio@226000 {
 			status = "okay";
 		};
 	};
-	nand_cs3@62000000 {
-		status = "okay";
-		pinctrl-names = "default";
-		pinctrl-0 = <&nand_cs3_pins>;
-	};
 	vbat: fixedregulator0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vbat";
@@ -250,3 +259,33 @@ &edma0 {
 &edma1 {
 	ti,edma-reserved-slot-ranges = <32 90>;
 };
+
+&aemif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_pins>;
+	status = "ok";
+	cs3 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		clock-ranges;
+		ranges;
+
+		ti,cs-chipselect = <3>;
+
+		nand@2000000,0 {
+			compatible = "ti,davinci-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0 0x02000000 0x02000000
+			       1 0x00000000 0x00008000>;
+
+			ti,davinci-chipselect = <1>;
+			ti,davinci-mask-ale = <0>;
+			ti,davinci-mask-cle = <0>;
+			ti,davinci-mask-chipsel = <0>;
+			ti,davinci-ecc-mode = "hw";
+			ti,davinci-ecc-bits = <4>;
+			ti,davinci-nand-use-bbt;
+		};
+	};
+};

arch/arm/boot/dts/da850-lcdk.dts

+/*
+ * Copyright (c) 2016 BayLibre, Inc.
+ *
+ * Licensed under GPLv2.
+ */
+/dts-v1/;
+#include "da850.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "DA850/AM1808/OMAP-L138 LCDK";
+	compatible = "ti,da850-lcdk", "ti,da850";
+
+	aliases {
+		serial2 = &serial2;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0xc0000000 0x08000000>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "DA850/OMAP-L138 LCDK";
+		simple-audio-card,widgets =
+			"Line", "Line In",
+			"Line", "Line Out";
+		simple-audio-card,routing =
+			"LINE1L", "Line In",
+			"LINE1R", "Line In",
+			"Line Out", "LLOUT",
+			"Line Out", "RLOUT";
+		simple-audio-card,format = "dsp_b";
+		simple-audio-card,bitclock-master = <&link0_codec>;
+		simple-audio-card,frame-master = <&link0_codec>;
+		simple-audio-card,bitclock-inversion;
+
+		simple-audio-card,cpu {
+			sound-dai = <&mcasp0>;
+			system-clock-frequency = <24576000>;
+		};
+
+		link0_codec: simple-audio-card,codec {
+			sound-dai = <&tlv320aic3106>;
+			system-clock-frequency = <24576000>;
+		};
+	};
+};
+
+&pmx_core {
+	status = "okay";
+
+	mcasp0_pins: pinmux_mcasp0_pins {
+		pinctrl-single,bits = <
+			/* AHCLKX AFSX ACLKX */
+			0x00 0x00101010 0x00f0f0f0
+			/* ARX13 ARX14 */
+			0x04 0x00000110 0x00000ff0
+		>;
+	};
+};
+
+&serial2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&serial2_rxtx_pins>;
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};
+
+&rtc0 {
+	status = "okay";
+};
+
+&gpio {
+	status = "okay";
+};
+
+&mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio_pins>;
+	bus_freq = <2200000>;
+	status = "okay";
+};
+
+&eth0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mii_pins>;
+	status = "okay";
+};
+
+&mmc0 {
+	max-frequency = <50000000>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	cd-gpios = <&gpio 64 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	tlv320aic3106: tlv320aic3106@18 {
+		#sound-dai-cells = <0>;
+		compatible = "ti,tlv320aic3106";
+		reg = <0x18>;
+		status = "okay";
+	};
+};
+
+&mcasp0 {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcasp0_pins>;
+	status = "okay";
+
+	op-mode = <0>;   /* DAVINCI_MCASP_IIS_MODE */
+	tdm-slots = <2>;
+	serial-dir = <   /* 0: INACTIVE, 1: TX, 2: RX */
+		0 0 0 0
+		0 0 0 0
+		0 0 0 0
+		0 1 2 0
+	>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+};

arch/arm/boot/dts/da850.dtsi

@@ -41,20 +41,40 @@ pmx_core: pinmux@14120 {
 			pinctrl-single,function-mask = <0xf>;
 			status = "disabled";
 
-			nand_cs3_pins: pinmux_nand_pins {
+			serial0_rtscts_pins: pinmux_serial0_rtscts_pins {
 				pinctrl-single,bits = <
-					/* EMA_OE, EMA_WE */
-					0x1c 0x00110000  0x00ff0000
-					/* EMA_CS[4],EMA_CS[3]*/
-					0x1c 0x00000110  0x00000ff0
-					/*
-					 * EMA_D[0], EMA_D[1], EMA_D[2],
-					 * EMA_D[3], EMA_D[4], EMA_D[5],
-					 * EMA_D[6], EMA_D[7]
-					 */
-					0x24 0x11111111  0xffffffff
-					/* EMA_A[1], EMA_A[2] */
-					0x30 0x01100000  0x0ff00000
+					/* UART0_RTS UART0_CTS */
+					0x0c 0x22000000 0xff000000
+				>;
+			};
+			serial0_rxtx_pins: pinmux_serial0_rxtx_pins {
+				pinctrl-single,bits = <
+					/* UART0_TXD UART0_RXD */
+					0x0c 0x00220000 0x00ff0000
+				>;
+			};
+			serial1_rtscts_pins: pinmux_serial1_rtscts_pins {
+				pinctrl-single,bits = <
+					/* UART1_CTS UART1_RTS */
+					0x00 0x00440000 0x00ff0000
+				>;
+			};
+			serial1_rxtx_pins: pinmux_serial1_rxtx_pins {
+				pinctrl-single,bits = <
+					/* UART1_TXD UART1_RXD */
+					0x10 0x22000000 0xff000000
+				>;
+			};
+			serial2_rtscts_pins: pinmux_serial2_rtscts_pins {
+				pinctrl-single,bits = <
+					/* UART2_CTS UART2_RTS */
+					0x00 0x44000000 0xff000000
+				>;
+			};
+			serial2_rxtx_pins: pinmux_serial2_rxtx_pins {
+				pinctrl-single,bits = <
+					/* UART2_TXD UART2_RXD */
+					0x10 0x00220000 0x00ff0000
 				>;
 			};
 			i2c0_pins: pinmux_i2c0_pins {
@@ -274,31 +294,36 @@ mmc1: mmc@21b000 {
 			status = "disabled";
 		};
 		ehrpwm0: pwm@300000 {
-			compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
+			compatible = "ti,da850-ehrpwm", "ti,am3352-ehrpwm",
+				     "ti,am33xx-ehrpwm";
 			#pwm-cells = <3>;
 			reg = <0x300000 0x2000>;
 			status = "disabled";
 		};
 		ehrpwm1: pwm@302000 {
-			compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
+			compatible = "ti,da850-ehrpwm", "ti,am3352-ehrpwm",
+				     "ti,am33xx-ehrpwm";
 			#pwm-cells = <3>;
 			reg = <0x302000 0x2000>;
 			status = "disabled";
 		};
 		ecap0: ecap@306000 {
-			compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+			compatible = "ti,da850-ecap", "ti,am3352-ecap",
+				     "ti,am33xx-ecap";
 			#pwm-cells = <3>;
 			reg = <0x306000 0x80>;
 			status = "disabled";
 		};
 		ecap1: ecap@307000 {
-			compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+			compatible = "ti,da850-ecap", "ti,am3352-ecap",
+				     "ti,am33xx-ecap";
 			#pwm-cells = <3>;
 			reg = <0x307000 0x80>;
 			status = "disabled";
 		};
 		ecap2: ecap@308000 {
-			compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+			compatible = "ti,da850-ecap", "ti,am3352-ecap",
+				     "ti,am33xx-ecap";
 			#pwm-cells = <3>;
 			reg = <0x308000 0x80>;
 			status = "disabled";
@@ -375,17 +400,14 @@ mcasp0: mcasp@100000 {
 			dma-names = "tx", "rx";
 		};
 	};
-	nand_cs3@62000000 {
-		compatible = "ti,davinci-nand";
-		reg = <0x62000000 0x807ff
-		       0x68000000 0x8000>;
-		ti,davinci-chipselect = <1>;
-		ti,davinci-mask-ale = <0>;
-		ti,davinci-mask-cle = <0>;
-		ti,davinci-mask-chipsel = <0>;
-		ti,davinci-ecc-mode = "hw";
-		ti,davinci-ecc-bits = <4>;
-		ti,davinci-nand-use-bbt;
+	aemif: aemif@68000000 {
+		compatible = "ti,da850-aemif";
+		#address-cells = <2>;
+		#size-cells = <1>;
+
+		reg = <0x68000000 0x00008000>;
+		ranges = <0 0 0x60000000 0x08000000
+			  1 0 0x68000000 0x00008000>;
 		status = "disabled";
 	};
 };

arch/arm/mach-davinci/da8xx-dt.c

@@ -49,6 +49,7 @@ static void __init da850_init_machine(void)
 
 static const char *const da850_boards_compat[] __initconst = {
 	"enbw,cmc",
+	"ti,da850-lcdk",
 	"ti,da850-evm",
 	"ti,da850",
 	NULL,