clk: xilinx: move xlnx_vcu clock driver from soc

The xlnx_vcu driver is actually a clock controller driver which provides
clocks that can be used by a driver for the encoder/decoder units. There
is no reason to keep this driver in soc. Move the driver to clk.

NOTE: The register mapping actually contains registers for AXI
performance monitoring, but these are not used by the driver.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20210121071659.1226489-16-m.tretter@pengutronix.deSigned-off-by: Stephen Boyd <sboyd@kernel.org>

drivers/clk/Kconfig

@@ -393,6 +393,7 @@ source "drivers/clk/tegra/Kconfig"
 source "drivers/clk/ti/Kconfig"
 source "drivers/clk/uniphier/Kconfig"
 source "drivers/clk/x86/Kconfig"
+source "drivers/clk/xilinx/Kconfig"
 source "drivers/clk/zynqmp/Kconfig"
 
 endif

drivers/clk/Makefile

@@ -122,6 +122,7 @@ obj-y					+= versatile/
 ifeq ($(CONFIG_COMMON_CLK), y)
 obj-$(CONFIG_X86)			+= x86/
 endif
+obj-y					+= xilinx/
 obj-$(CONFIG_ARCH_ZX)			+= zte/
 obj-$(CONFIG_ARCH_ZYNQ)			+= zynq/
 obj-$(CONFIG_COMMON_CLK_ZYNQMP)         += zynqmp/

drivers/clk/xilinx/Kconfig

+# SPDX-License-Identifier: GPL-2.0
+
+config XILINX_VCU
+	tristate "Xilinx VCU logicoreIP Init"
+	depends on HAS_IOMEM && COMMON_CLK
+	select REGMAP_MMIO
+	help
+	  Provides the driver to enable and disable the isolation between the
+	  processing system and programmable logic part by using the logicoreIP
+	  register set. This driver also configures the frequency based on the
+	  clock information from the logicoreIP register set.
+
+	  If you say yes here you get support for the logicoreIP.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called xlnx_vcu.
+

drivers/clk/xilinx/Makefile

+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_XILINX_VCU)	+= xlnx_vcu.o

drivers/soc/xilinx/Kconfig

 # SPDX-License-Identifier: GPL-2.0
 menu "Xilinx SoC drivers"
 
-config XILINX_VCU
-	tristate "Xilinx VCU logicoreIP Init"
-	depends on HAS_IOMEM && COMMON_CLK
-	select REGMAP_MMIO
-	help
-	  Provides the driver to enable and disable the isolation between the
-	  processing system and programmable logic part by using the logicoreIP
-	  register set. This driver also configures the frequency based on the
-	  clock information from the logicoreIP register set.
-
-	  If you say yes here you get support for the logicoreIP.
-
-	  If unsure, say N.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called xlnx_vcu.
-
 config ZYNQMP_POWER
 	bool "Enable Xilinx Zynq MPSoC Power Management driver"
 	depends on PM && ZYNQMP_FIRMWARE

drivers/soc/xilinx/Makefile

 # SPDX-License-Identifier: GPL-2.0
-obj-$(CONFIG_XILINX_VCU)	+= xlnx_vcu.o
 obj-$(CONFIG_ZYNQMP_POWER)	+= zynqmp_power.o
 obj-$(CONFIG_ZYNQMP_PM_DOMAINS) += zynqmp_pm_domains.o