Skip to content

L
linux
Commit a43315e3 authored by Olof Johansson's avatar Olof Johansson
Browse files
Options

Merge tag 'imx-dt-4.12' of... 

Merge tag 'imx-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt

i.MX device tree updates for 4.12:
 - New board support: I2SE's i.MX28 Duckbill-2 boards, Gateworks Ventana
   i.MX6 GW5903/GW5904, Zodiac Inflight Innovations RDU2 board, Engicam
   i.CoreM6 Quad/Dual OpenFrame modules, Boundary Device i.MX6 Quad Plus
   SOM.
 - Improve compatible string for i.MX50 eSDHC, i.MX7S SRC devices and
   i.MX6SX UART device.
 - Add interrupts for switch and PHY devices on VF610 ZII Devel C board.
 - Add LVDS, LCD backlight, touchscreen and SAI2 support for i.MX6
   icore, geam, and isiot boards.
 - A series from Lucas Stach to improve i.MX6Q Plus device tree and add
   PRE/PRG devices.
 - A series from Stefan Agner to update imx7-colibri device tree
   regarding to display, PMIC/regulator support.
 - Fix PCI bus DTC warnings seen with the latest compiler.
 - Set default phy_type and dr_mode for i.MX25 USBOTG port.
 - A couple of small improvements on i.MX25 pin function DT header.
 - Add audio support for imx6q-cm-fx6 board using Wolfson wm8731 codec
   which is muxed to SSI2 device.
 - Other random updates, small fixes and trivial cleanups.

* tag 'imx-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (56 commits)
  ARM: dts: imx6q-utilite-pro: add hpd gpio
  ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
  ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
  ARM: dts: imx: add Gateworks Ventana GW5903 support
  ARM: dts: i.MX25: add AIPS control registers
  ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
  ARM: dts: imx7-colibri: remove 1.8V fixed regulator
  ARM: dts: imx7-colibri: allow to disable Ethernet rail
  ARM: dts: imx7-colibri: fix PMIC voltages
  ARM: dts: imx7-colibri: use OF graph to describe the display
  ARM: dts: imx6qp-nitrogen6_som2: add Quad Plus variant of the SOM
  ARM: dts: imx6q-icore: Add touchscreen node
  ARM: dts: vf610-zii-dev-rev-b: change switch2 label
  ARM: dts: imx6ul-[geam|isiot]: Add sai2 node
  ARM: dts: imx6ul-isiot-common: Add touchscreen node
  ARM: dts: imx6ul-isiot: Add i2c nodes
  ARM: dts: imx6ul-isiot: Add imx6ul-isiot-common.dtsi
  ARM: dts: imx6ul-isiot: Add backlight support for lcdif
  ARM: dts: imx6ul-geam: Add backlight support for lcdif
  ARM: dts: imx6: add ZII RDU2 boards
  ...
Signed-off-by: default avatarOlof Johansson <olof@lixom.net>
parents b633b314 e48d9e71
Expand all Hide whitespace changes
Inline Side-by-side
Showing with 4499 additions and 172 deletions
Documentation/devicetree/bindings/arm/i2se.txt 0 → 100644
View file @ a43315e3
I2SE Device Tree Bindings
-------------------------
Duckbill Board
Required root node properties:
- compatible = "i2se,duckbill", "fsl,imx28";
Duckbill 2 Board
Required root node properties:
- compatible = "i2se,duckbill-2", "fsl,imx28";
Duckbill 2 485 Board
Required root node properties:
- compatible = "i2se,duckbill-2-485", "i2se,duckbill-2", "fsl,imx28";
Duckbill 2 EnOcean Board
Required root node properties:
- compatible = "i2se,duckbill-2-enocean", "i2se,duckbill-2", "fsl,imx28";
Duckbill 2 SPI Board
Required root node properties:
- compatible = "i2se,duckbill-2-spi", "i2se,duckbill-2", "fsl,imx28";
arch/arm/boot/dts/Makefile
View file @ a43315e3
......@@ -363,6 +363,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-gw551x.dtb \
imx6dl-gw552x.dtb \
imx6dl-gw553x.dtb \
imx6dl-gw5903.dtb \
imx6dl-gw5904.dtb \
imx6dl-hummingboard.dtb \
imx6dl-icore.dtb \
imx6dl-icore-rqs.dtb \
......@@ -406,9 +408,13 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-gw551x.dtb \
imx6q-gw552x.dtb \
imx6q-gw553x.dtb \
imx6q-gw5903.dtb \
imx6q-gw5904.dtb \
imx6q-h100.dtb \
imx6q-hummingboard.dtb \
imx6q-icore.dtb \
imx6q-icore-ofcap10.dtb \
imx6q-icore-ofcap12.dtb \
imx6q-icore-rqs.dtb \
imx6q-marsboard.dtb \
imx6q-mccmon6.dtb \
......@@ -436,9 +442,12 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-utilite-pro.dtb \
imx6q-wandboard.dtb \
imx6q-wandboard-revb1.dtb \
imx6q-zii-rdu2.dtb \
imx6qp-nitrogen6_max.dtb \
imx6qp-nitrogen6_som2.dtb \
imx6qp-sabreauto.dtb \
imx6qp-sabresd.dtb
imx6qp-sabresd.dtb \
imx6qp-zii-rdu2.dtb
dtb-$(CONFIG_SOC_IMX6SL) += \
imx6sl-evk.dtb \
imx6sl-warp.dtb
......@@ -469,6 +478,7 @@ dtb-$(CONFIG_SOC_IMX7D) += \
imx7d-nitrogen7.dtb \
imx7d-sbc-imx7.dtb \
imx7d-sdb.dtb \
imx7d-sdb-sht11.dtb \
imx7s-colibri-eval-v3.dtb \
imx7s-warp.dtb
dtb-$(CONFIG_SOC_LS1021A) += \
......@@ -499,6 +509,10 @@ dtb-$(CONFIG_ARCH_MXS) += \
imx28-cfa10056.dtb \
imx28-cfa10057.dtb \
imx28-cfa10058.dtb \
imx28-duckbill-2-485.dtb \
imx28-duckbill-2.dtb \
imx28-duckbill-2-enocean.dtb \
imx28-duckbill-2-spi.dtb \
imx28-duckbill.dtb \
imx28-eukrea-mbmx283lc.dtb \
imx28-eukrea-mbmx287lc.dtb \
......
arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard.dts
View file @ a43315e3
......@@ -179,8 +179,6 @@ &usbhost1 {
};
&usbotg {
phy_type = "utmi";
dr_mode = "otg";
external-vbus-divider;
status = "okay";
};
arch/arm/boot/dts/imx25-pdk.dts
View file @ a43315e3
......@@ -309,8 +309,6 @@ &usbhost1 {
};
&usbotg {
phy_type = "utmi";
dr_mode = "otg";
external-vbus-divider;
status = "okay";
};
arch/arm/boot/dts/imx25-pinfunc.h
View file @ a43315e3
......@@ -17,8 +17,6 @@
* <mux_reg conf_reg input_reg mux_mode input_val>
*/
#define MX25_PAD_TDO__TDO 0x000 0x3e8 0x000 0x00 0x000
#define MX25_PAD_A10__A10 0x008 0x000 0x000 0x00 0x000
#define MX25_PAD_A10__GPIO_4_0 0x008 0x000 0x000 0x05 0x000
......@@ -68,7 +66,6 @@
#define MX25_PAD_A22__A22 0x030 0x000 0x000 0x00 0x000
#define MX25_PAD_A22__GPIO_2_8 0x030 0x000 0x000 0x05 0x000
#define MX25_PAD_A22__FEC_TDATA2 0x030 0x000 0x000 0x07 0x000
#define MX25_PAD_A22__SIM2_VEN1 0x030 0x000 0x000 0x06 0x000
#define MX25_PAD_A22__FEC_TDATA2 0x030 0x000 0x000 0x07 0x000
......@@ -542,6 +539,8 @@
#define MX25_PAD_RTCK__OWIRE 0x1ec 0x3e4 0x000 0x01 0x000
#define MX25_PAD_RTCK__GPIO_3_14 0x1ec 0x3e4 0x000 0x05 0x000
#define MX25_PAD_TDO__TDO 0x000 0x3e8 0x000 0x00 0x000
#define MX25_PAD_DE_B__DE_B 0x1f0 0x3ec 0x000 0x00 0x000
#define MX25_PAD_DE_B__GPIO_2_20 0x1f0 0x3ec 0x000 0x05 0x000
......
arch/arm/boot/dts/imx25.dtsi
View file @ a43315e3
......@@ -93,6 +93,11 @@ aips@43f00000 { /* AIPS1 */
reg = <0x43f00000 0x100000>;
ranges;
aips1: bridge@43f00000 {
compatible = "fsl,imx25-aips";
reg = <0x43f00000 0x4000>;
};
i2c1: i2c@43f80000 {
#address-cells = <1>;
#size-cells = <0>;
......@@ -342,6 +347,11 @@ aips@53f00000 { /* AIPS2 */
reg = <0x53f00000 0x100000>;
ranges;
aips2: bridge@53f00000 {
compatible = "fsl,imx25-aips";
reg = <0x53f00000 0x4000>;
};
clks: ccm@53f80000 {
compatible = "fsl,imx25-ccm";
reg = <0x53f80000 0x4000>;
......@@ -544,6 +554,8 @@ usbotg: usb@53ff4000 {
clock-names = "ipg", "ahb", "per";
fsl,usbmisc = <&usbmisc 0>;
fsl,usbphy = <&usbphy0>;
phy_type = "utmi";
dr_mode = "otg";
status = "disabled";
};
......
arch/arm/boot/dts/imx28-duckbill-2-485.dts 0 → 100644
View file @ a43315e3
/*
* Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
* Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
/dts-v1/;
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
#include "imx28.dtsi"
/ {
model = "I2SE Duckbill 2 485";
compatible = "i2se,duckbill-2-485", "i2se,duckbill-2", "fsl,imx28";
memory {
reg = <0x40000000 0x08000000>;
};
apb@80000000 {
apbh@80000000 {
ssp0: ssp@80010000 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc0_8bit_pins_a
&mmc0_cd_cfg &mmc0_sck_cfg>;
bus-width = <8>;
vmmc-supply = <&reg_3p3v>;
status = "okay";
non-removable;
};
ssp2: ssp@80014000 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc2_4bit_pins_b
&mmc2_cd_cfg &mmc2_sck_cfg_b>;
bus-width = <4>;
vmmc-supply = <&reg_3p3v>;
status = "okay";
};
pinctrl@80018000 {
pinctrl-names = "default";
pinctrl-0 = <&hog_pins_a>;
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_phy_reset_pin: mac0-phy-reset@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_phy_int_pin: mac0-phy-int@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
led_pins: leds@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SAIF0_MCLK__GPIO_3_20
MX28_PAD_SAIF0_LRCLK__GPIO_3_21
MX28_PAD_I2C0_SCL__GPIO_3_24
MX28_PAD_I2C0_SDA__GPIO_3_25
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
};
apbx@80040000 {
lradc@80050000 {
status = "okay";
};
auart0: serial@8006a000 {
pinctrl-names = "default";
pinctrl-0 = <&auart0_2pins_a>;
status = "okay";
};
duart: serial@80074000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_a>;
status = "okay";
};
usbphy0: usbphy@8007c000 {
status = "okay";
};
};
};
ahb@80080000 {
usb0: usb@80080000 {
status = "okay";
dr_mode = "peripheral";
};
mac0: ethernet@800f0000 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
phy-supply = <&reg_3p3v>;
phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
phy-reset-duration = <25>;
phy-handle = <&ethphy>;
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
ethphy: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0>;
pinctrl-names = "default";
pinctrl-0 = <&mac0_phy_int_pin>;
interrupt-parent = <&gpio0>;
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
max-speed = <100>;
};
};
};
};
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pins>;
status-red {
label = "duckbill:red:status";
gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "default-on";
};
status-green {
label = "duckbill:green:status";
gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
rs485-red {
label = "duckbill:red:rs485";
gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
};
rs485-green {
label = "duckbill:green:rs485";
gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
};
};
};
arch/arm/boot/dts/imx28-duckbill-2-enocean.dts 0 → 100644
View file @ a43315e3
/*
* Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
* Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
/dts-v1/;
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include "imx28.dtsi"
/ {
model = "I2SE Duckbill 2 EnOcean";
compatible = "i2se,duckbill-2-enocean", "i2se,duckbill-2", "fsl,imx28";
memory {
reg = <0x40000000 0x08000000>;
};
apb@80000000 {
apbh@80000000 {
ssp0: ssp@80010000 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc0_8bit_pins_a
&mmc0_cd_cfg &mmc0_sck_cfg>;
bus-width = <8>;
vmmc-supply = <&reg_3p3v>;
status = "okay";
non-removable;
};
ssp2: ssp@80014000 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc2_4bit_pins_b
&mmc2_cd_cfg &mmc2_sck_cfg_b>;
bus-width = <4>;
vmmc-supply = <&reg_3p3v>;
status = "okay";
};
pinctrl@80018000 {
pinctrl-names = "default";
pinctrl-0 = <&hog_pins_a>;
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_phy_reset_pin: mac0-phy-reset@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_phy_int_pin: mac0-phy-int@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
led_pins: leds@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SAIF0_MCLK__GPIO_3_20
MX28_PAD_SAIF0_LRCLK__GPIO_3_21
MX28_PAD_AUART0_CTS__GPIO_3_2
MX28_PAD_I2C0_SCL__GPIO_3_24
MX28_PAD_I2C0_SDA__GPIO_3_25
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
enocean_button: enocean-button@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_AUART0_RTS__GPIO_3_3
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
};
apbx@80040000 {
lradc@80050000 {
status = "okay";
};
auart0: serial@8006a000 {
pinctrl-names = "default";
pinctrl-0 = <&auart0_2pins_a>;
status = "okay";
};
duart: serial@80074000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_a>;
status = "okay";
};
usbphy0: usbphy@8007c000 {
status = "okay";
};
};
};
ahb@80080000 {
usb0: usb@80080000 {
status = "okay";
dr_mode = "peripheral";
};
mac0: ethernet@800f0000 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
phy-supply = <&reg_3p3v>;
phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
phy-reset-duration = <25>;
phy-handle = <&ethphy>;
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
ethphy: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0>;
pinctrl-names = "default";
pinctrl-0 = <&mac0_phy_int_pin>;
interrupt-parent = <&gpio0>;
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
max-speed = <100>;
};
};
};
};
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pins>;
status-red {
label = "duckbill:red:status";
gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "default-on";
};
status-green {
label = "duckbill:green:status";
gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
enocean-blue {
label = "duckbill:blue:enocean";
gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
};
enocean-red {
label = "duckbill:red:enocean";
gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
};
enocean-green {
label = "duckbill:green:enocean";
gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
};
};
gpio-keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&enocean_button>;
enocean {
label = "EnOcean";
linux,code = <KEY_NEW>;
gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>;
};
};
};
arch/arm/boot/dts/imx28-duckbill-2-spi.dts 0 → 100644
View file @ a43315e3
/*
* Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
* Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
/dts-v1/;
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
#include "imx28.dtsi"
/ {
model = "I2SE Duckbill 2 SPI";
compatible = "i2se,duckbill-2-spi", "i2se,duckbill-2", "fsl,imx28";
aliases {
ethernet1 = &qca7000;
};
memory {
reg = <0x40000000 0x08000000>;
};
apb@80000000 {
apbh@80000000 {
ssp0: ssp@80010000 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc0_8bit_pins_a
&mmc0_cd_cfg &mmc0_sck_cfg>;
bus-width = <8>;
vmmc-supply = <&reg_3p3v>;
status = "okay";
non-removable;
};
ssp2: ssp@80014000 {
compatible = "fsl,imx28-spi";
pinctrl-names = "default";
pinctrl-0 = <&spi2_pins_a>;
status = "okay";
qca7000: ethernet@0 {
reg = <0>;
compatible = "qca,qca7000";
pinctrl-names = "default";
pinctrl-0 = <&qca7000_pins>;
interrupt-parent = <&gpio3>;
interrupts = <3 IRQ_TYPE_EDGE_RISING>;
spi-cpha;
spi-cpol;
spi-max-frequency = <8000000>;
};
};
pinctrl@80018000 {
pinctrl-names = "default";
pinctrl-0 = <&hog_pins_a>;
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_phy_reset_pin: mac0-phy-reset@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_phy_int_pin: mac0-phy-int@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
led_pins: led@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SAIF0_MCLK__GPIO_3_20
MX28_PAD_SAIF0_LRCLK__GPIO_3_21
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
qca7000_pins: qca7000@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_AUART0_RTS__GPIO_3_3 /* Interrupt */
MX28_PAD_LCD_D13__GPIO_1_13 /* QCA7K reset */
MX28_PAD_LCD_D14__GPIO_1_14 /* GPIO 0 */
MX28_PAD_LCD_D15__GPIO_1_15 /* GPIO 1 */
MX28_PAD_LCD_D18__GPIO_1_18 /* GPIO 2 */
MX28_PAD_LCD_D21__GPIO_1_21 /* GPIO 3 */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
};
apbx@80040000 {
lradc@80050000 {
status = "okay";
};
duart: serial@80074000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_a>;
status = "okay";
};
usbphy0: usbphy@8007c000 {
status = "okay";
};
};
};
ahb@80080000 {
usb0: usb@80080000 {
status = "okay";
dr_mode = "peripheral";
};
mac0: ethernet@800f0000 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
phy-supply = <&reg_3p3v>;
phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
phy-reset-duration = <25>;
phy-handle = <&ethphy>;
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
ethphy: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0>;
pinctrl-names = "default";
pinctrl-0 = <&mac0_phy_int_pin>;
interrupt-parent = <&gpio0>;
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
max-speed = <100>;
};
};
};
};
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pins>;
status-red {
label = "duckbill:red:status";
gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "default-on";
};
status-green {
label = "duckbill:green:status";
gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
};
arch/arm/boot/dts/imx28-duckbill-2.dts 0 → 100644
View file @ a43315e3
/*
* Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
* Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
/dts-v1/;
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
#include "imx28.dtsi"
/ {
model = "I2SE Duckbill 2";
compatible = "i2se,duckbill-2", "fsl,imx28";
memory {
reg = <0x40000000 0x08000000>;
};
apb@80000000 {
apbh@80000000 {
ssp0: ssp@80010000 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc0_8bit_pins_a
&mmc0_cd_cfg &mmc0_sck_cfg>;
bus-width = <8>;
vmmc-supply = <&reg_3p3v>;
status = "okay";
non-removable;
};
ssp2: ssp@80014000 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc2_4bit_pins_b
&mmc2_cd_cfg &mmc2_sck_cfg_b>;
bus-width = <4>;
vmmc-supply = <&reg_3p3v>;
status = "okay";
};
pinctrl@80018000 {
pinctrl-names = "default";
pinctrl-0 = <&hog_pins_a>;
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_phy_reset_pin: mac0-phy-reset@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_phy_int_pin: mac0-phy-int@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
led_pins: leds@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SAIF0_MCLK__GPIO_3_20
MX28_PAD_SAIF0_LRCLK__GPIO_3_21
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
};
apbx@80040000 {
lradc@80050000 {
status = "okay";
};
i2c0: i2c@80058000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
};
auart0: serial@8006a000 {
pinctrl-names = "default";
pinctrl-0 = <&auart0_2pins_a>;
status = "okay";
};
duart: serial@80074000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_a>;
status = "okay";
};
usbphy0: usbphy@8007c000 {
status = "okay";
};
};
};
ahb@80080000 {
usb0: usb@80080000 {
status = "okay";
dr_mode = "peripheral";
};
mac0: ethernet@800f0000 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
phy-supply = <&reg_3p3v>;
phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
phy-reset-duration = <25>;
phy-handle = <&ethphy>;
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
ethphy: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0>;
pinctrl-names = "default";
pinctrl-0 = <&mac0_phy_int_pin>;
interrupt-parent = <&gpio0>;
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
max-speed = <100>;
};
};
};
};
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pins>;
status-red {
label = "duckbill:red:status";
gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "default-on";
};
status-green {
label = "duckbill:green:status";
gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
};
arch/arm/boot/dts/imx28-duckbill.dts
View file @ a43315e3
/*
* Copyright (C) 2013 Michael Heimpold <mhei@heimpold.de>
* Copyright (C) 2013-2014,2016 Michael Heimpold <mhei@heimpold.de>
* Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
......@@ -10,6 +11,7 @@
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include "imx28.dtsi"
/ {
......@@ -32,6 +34,13 @@ ssp0: ssp@80010000 {
status = "okay";
};
ssp2: ssp@80014000 {
compatible = "fsl,imx28-spi";
pinctrl-names = "default";
pinctrl-0 = <&spi2_pins_a>;
status = "okay";
};
pinctrl@80018000 {
pinctrl-names = "default";
pinctrl-0 = <&hog_pins_a>;
......@@ -39,14 +48,24 @@ pinctrl@80018000 {
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */
MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_phy_reset_pin: mac0-phy-reset@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
led_pins_a: led_gpio@0 {
led_pins: leds@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_AUART1_RX__GPIO_3_4
......@@ -60,6 +79,22 @@ MX28_PAD_AUART1_TX__GPIO_3_5
};
apbx@80040000 {
lradc@80050000 {
status = "okay";
};
i2c0: i2c@80058000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
};
auart0: serial@8006a000 {
pinctrl-names = "default";
pinctrl-0 = <&auart0_2pins_a>;
status = "okay";
};
duart: serial@80074000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_a>;
......@@ -75,47 +110,43 @@ usbphy0: usbphy@8007c000 {
ahb@80080000 {
usb0: usb@80080000 {
status = "okay";
dr_mode = "peripheral";
};
mac0: ethernet@800f0000 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>;
pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
phy-supply = <&reg_3p3v>;
phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
phy-reset-duration = <100>;
phy-reset-duration = <25>;
status = "okay";
};
};
regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
reg_3p3v: regulator@0 {
compatible = "regulator-fixed";
reg = <0>;
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pins_a>;
pinctrl-0 = <&led_pins>;
status {
label = "duckbill:green:status";
gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
};
failure {
status-red {
label = "duckbill:red:status";
gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "default-on";
};
status-green {
label = "duckbill:green:status";
gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
};
arch/arm/boot/dts/imx28-m28cu3.dts
View file @ a43315e3
......@@ -57,7 +57,7 @@ ssp2: ssp@80014000 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_4bit_pins_a
&mmc2_cd_cfg
&mmc2_sck_cfg>;
&mmc2_sck_cfg_a>;
bus-width = <4>;
vmmc-supply = <&reg_vddio_sd1>;
status = "okay";
......
arch/arm/boot/dts/imx28.dtsi
View file @ a43315e3
......@@ -590,6 +590,22 @@ MX28_PAD_SSP0_DATA7__SSP2_SCK
fsl,pull-up = <MXS_PULL_ENABLE>;
};
mmc2_4bit_pins_b: mmc2-4bit@1 {
reg = <1>;
fsl,pinmux-ids = <
MX28_PAD_SSP2_SCK__SSP2_SCK
MX28_PAD_SSP2_MOSI__SSP2_CMD
MX28_PAD_SSP2_MISO__SSP2_D0
MX28_PAD_SSP2_SS0__SSP2_D3
MX28_PAD_SSP2_SS1__SSP2_D1
MX28_PAD_SSP2_SS2__SSP2_D2
MX28_PAD_AUART1_RX__SSP2_CARD_DETECT
>;
fsl,drive-strength = <MXS_DRIVE_8mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_ENABLE>;
};
mmc2_cd_cfg: mmc2-cd-cfg {
fsl,pinmux-ids = <
MX28_PAD_AUART1_RX__SSP2_CARD_DETECT
......@@ -597,7 +613,8 @@ MX28_PAD_AUART1_RX__SSP2_CARD_DETECT
fsl,pull-up = <MXS_PULL_DISABLE>;
};
mmc2_sck_cfg: mmc2-sck-cfg {
mmc2_sck_cfg_a: mmc2-sck-cfg@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP0_DATA7__SSP2_SCK
>;
......@@ -605,6 +622,15 @@ MX28_PAD_SSP0_DATA7__SSP2_SCK
fsl,pull-up = <MXS_PULL_DISABLE>;
};
mmc2_sck_cfg_b: mmc2-sck-cfg@1 {
reg = <1>;
fsl,pinmux-ids = <
MX28_PAD_SSP2_SCK__SSP2_SCK
>;
fsl,drive-strength = <MXS_DRIVE_12mA>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
i2c0_pins_a: i2c0@0 {
reg = <0>;
fsl,pinmux-ids = <
......
arch/arm/boot/dts/imx50.dtsi
View file @ a43315e3
......@@ -109,7 +109,7 @@ spba@50000000 {
ranges;
esdhc1: esdhc@50004000 {
compatible = "fsl,imx50-esdhc";
compatible = "fsl,imx50-esdhc", "fsl,imx53-esdhc";
reg = <0x50004000 0x4000>;
interrupts = <1>;
clocks = <&clks IMX5_CLK_ESDHC1_IPG_GATE>,
......@@ -121,7 +121,7 @@ esdhc1: esdhc@50004000 {
};
esdhc2: esdhc@50008000 {
compatible = "fsl,imx50-esdhc";
compatible = "fsl,imx50-esdhc", "fsl,imx53-esdhc";
reg = <0x50008000 0x4000>;
interrupts = <2>;
clocks = <&clks IMX5_CLK_ESDHC2_IPG_GATE>,
......@@ -170,7 +170,7 @@ ssi2: ssi@50014000 {
};
esdhc3: esdhc@50020000 {
compatible = "fsl,imx50-esdhc";
compatible = "fsl,imx50-esdhc", "fsl,imx53-esdhc";
reg = <0x50020000 0x4000>;
interrupts = <3>;
clocks = <&clks IMX5_CLK_ESDHC3_IPG_GATE>,
......@@ -182,7 +182,7 @@ esdhc3: esdhc@50020000 {
};
esdhc4: esdhc@50024000 {
compatible = "fsl,imx50-esdhc";
compatible = "fsl,imx50-esdhc", "fsl,imx53-esdhc";
reg = <0x50024000 0x4000>;
interrupts = <4>;
clocks = <&clks IMX5_CLK_ESDHC4_IPG_GATE>,
......
arch/arm/boot/dts/imx53-qsb.dts
View file @ a43315e3
......@@ -88,8 +88,8 @@ ldo6_reg: ldo6 {
};
ldo7_reg: ldo7 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <3600000>;
regulator-min-microvolt = <2750000>;
regulator-max-microvolt = <2750000>;
};
ldo8_reg: ldo8 {
......
arch/arm/boot/dts/imx53-qsrb.dts
View file @ a43315e3
......@@ -128,8 +128,8 @@ vusb2_reg: vusb2 {
vdac_reg: vdac {
regulator-name = "VDAC";
regulator-min-microvolt = <2500000>;
regulator-max-microvolt = <2775000>;
regulator-min-microvolt = <2750000>;
regulator-max-microvolt = <2750000>;
};
vgen1_reg: vgen1 {
......
arch/arm/boot/dts/imx6dl-gw5903.dts 0 → 100644
View file @ a43315e3
/*
* Copyright 2017 Gateworks Corporation
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public
* License along with this file; if not, write to the Free
* Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
* MA 02110-1301 USA
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "imx6dl.dtsi"
#include "imx6qdl-gw5903.dtsi"
/ {
model = "Gateworks Ventana i.MX6 Duallite/Solo GW5903";
compatible = "gw,imx6dl-gw5903", "gw,ventana", "fsl,imx6dl";
};
arch/arm/boot/dts/imx6dl-gw5904.dts 0 → 100644
View file @ a43315e3
/*
* Copyright 2017 Gateworks Corporation
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public
* License along with this file; if not, write to the Free
* Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
* MA 02110-1301 USA
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "imx6dl.dtsi"
#include "imx6qdl-gw5904.dtsi"
/ {
model = "Gateworks Ventana i.MX6 DualLite/Solo GW5904";
compatible = "gw,imx6dl-gw5904", "gw,ventana", "fsl,imx6dl";
};
arch/arm/boot/dts/imx6q-b450v3.dts
View file @ a43315e3
......@@ -104,4 +104,11 @@ P05 {
output-low;
line-name = "PCA9539-P05";
};
P07 {
gpio-hog;
gpios = <7 0>;
output-low;
line-name = "PCA9539-P07";
};
};
arch/arm/boot/dts/imx6q-b650v3.dts
View file @ a43315e3
......@@ -97,6 +97,13 @@ P05 {
output-low;
line-name = "PCA9539-P05";
};
P07 {
gpio-hog;
gpios = <7 0>;
output-low;
line-name = "PCA9539-P07";
};
};
&usbphy1 {
......
arch/arm/boot/dts/imx6q-b850v3.dts
View file @ a43315e3
......@@ -72,6 +72,14 @@ lvds0: lvds-channel@0 {
fsl,data-mapping = "spwg";
fsl,data-width = <24>;
status = "okay";
port@4 {
reg = <4>;
lvds0_out: endpoint {
remote-endpoint = <&stdp4028_in>;
};
};
};
};
......@@ -142,3 +150,65 @@ ads7830@4a {
reg = <0x4a>;
};
};
&mux2_i2c2 {
clock-frequency = <100000>;
stdp2690@72 {
compatible = "megachips,stdp2690-ge-b850v3-fw";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x72>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
stdp2690_in: endpoint {
remote-endpoint = <&stdp4028_out>;
};
};
port@1 {
reg = <1>;
stdp2690_out: endpoint {
/* Connector for external display */
};
};
};
};
stdp4028@73 {
compatible = "megachips,stdp4028-ge-b850v3-fw";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x73>;
interrupt-parent = <&gpio2>;
interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
stdp4028_in: endpoint {
remote-endpoint = <&lvds0_out>;
};
};
port@1 {
reg = <1>;
stdp4028_out: endpoint {
remote-endpoint = <&stdp2690_in>;
};
};
};
};
};
arch/arm/boot/dts/imx6q-bx50v3.dtsi
View file @ a43315e3
......@@ -102,7 +102,7 @@ &ecspi5 {
m25_eeprom: m25p80@0 {
compatible = "atmel,at25";
spi-max-frequency = <20000000>;
spi-max-frequency = <10000000>;
size = <0x8000>;
pagesize = <64>;
reg = <0>;
......@@ -183,20 +183,6 @@ pca9539: pca9539@74 {
interrupt-parent = <&gpio2>;
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
P06 {
gpio-hog;
gpios = <6 0>;
output-low;
line-name = "PCA9539-P06";
};
P07 {
gpio-hog;
gpios = <7 0>;
output-low;
line-name = "PCA9539-P07";
};
P10 {
gpio-hog;
gpios = <8 0>;
......
arch/arm/boot/dts/imx6q-cm-fx6.dts
View file @ a43315e3
......@@ -43,6 +43,7 @@
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/sound/fsl-imx-audmux.h>
#include "imx6q.dtsi"
/ {
......@@ -90,6 +91,34 @@ reg_usb_otg_vbus: usb_otg_vbus {
enable-active-high;
};
sound-analog {
compatible = "simple-audio-card";
simple-audio-card,name = "On-board analog audio";
simple-audio-card,widgets =
"Headphone", "Headphone Jack",
"Line", "Line Out",
"Microphone", "Mic Jack",
"Line", "Line In";
simple-audio-card,routing =
"Headphone Jack", "RHPOUT",
"Headphone Jack", "LHPOUT",
"MICIN", "Mic Bias",
"Mic Bias", "Mic Jack";
simple-audio-card,format = "i2s";
simple-audio-card,bitclock-master = <&sound_master>;
simple-audio-card,frame-master = <&sound_master>;
simple-audio-card,bitclock-inversion;
sound_master: simple-audio-card,cpu {
sound-dai = <&ssi2>;
system-clock-frequency = <2822400>;
};
simple-audio-card,codec {
sound-dai = <&wm8731>;
};
};
sound-spdif {
compatible = "fsl,imx-audio-spdif";
model = "imx-spdif";
......@@ -99,6 +128,36 @@ sound-spdif {
};
};
&audmux {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_audmux>;
status = "okay";
ssi2 {
fsl,audmux-port = <1>;
fsl,port-config = <
(IMX_AUDMUX_V2_PTCR_RCLKDIR |
IMX_AUDMUX_V2_PTCR_RCSEL(3 | 0x8) |
IMX_AUDMUX_V2_PTCR_TCLKDIR |
IMX_AUDMUX_V2_PTCR_TCSEL(3))
IMX_AUDMUX_V2_PDCR_RXDSEL(3)
>;
};
audmux4 {
fsl,audmux-port = <3>;
fsl,port-config = <
(IMX_AUDMUX_V2_PTCR_TFSDIR |
IMX_AUDMUX_V2_PTCR_TFSEL(1) |
IMX_AUDMUX_V2_PTCR_RCLKDIR |
IMX_AUDMUX_V2_PTCR_RCSEL(1 | 0x8) |
IMX_AUDMUX_V2_PTCR_TCLKDIR |
IMX_AUDMUX_V2_PTCR_TCSEL(1))
IMX_AUDMUX_V2_PDCR_RXDSEL(1)
>;
};
};
&cpu0 {
/*
* Although the imx6q fuse indicates that 1.2GHz operation is possible,
......@@ -160,9 +219,25 @@ eeprom@50 {
reg = <0x50>;
pagesize = <16>;
};
wm8731: codec@1a {
#sound-dai-cells = <0>;
compatible = "wlf,wm8731";
reg = <0x1a>;
};
};
&iomuxc {
pinctrl_audmux: audmuxgrp {
fsl,pins = <
MX6QDL_PAD_SD2_CMD__AUD4_RXC 0x17059
MX6QDL_PAD_SD2_DAT0__AUD4_RXD 0x17059
MX6QDL_PAD_SD2_DAT3__AUD4_TXC 0x17059
MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x17059
MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x17059
>;
};
pinctrl_ecspi1: ecspi1grp {
fsl,pins = <
MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
......@@ -279,6 +354,14 @@ &spdif {
status = "okay";
};
&ssi2 {
assigned-clocks = <&clks IMX6QDL_CLK_SSI2_SEL>,
<&clks IMX6QDL_CLK_PLL4_AUDIO_DIV>;
assigned-clock-parents = <&clks IMX6QDL_CLK_PLL4_AUDIO_DIV>;
assigned-clock-rates = <0>, <786432000>;
status = "okay";
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
......
arch/arm/boot/dts/imx6q-gw5903.dts 0 → 100644
View file @ a43315e3
/*
* Copyright 2017 Gateworks Corporation
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public
* License along with this file; if not, write to the Free
* Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
* MA 02110-1301 USA
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "imx6q.dtsi"
#include "imx6qdl-gw5903.dtsi"
/ {
model = "Gateworks Ventana i.MX6 Dual/Quad GW5903";
compatible = "gw,imx6q-gw5903", "gw,ventana", "fsl,imx6q";
};
arch/arm/boot/dts/imx6q-gw5904.dts 0 → 100644
View file @ a43315e3
/*
* Copyright 2017 Gateworks Corporation
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public
* License along with this file; if not, write to the Free
* Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
* MA 02110-1301 USA
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "imx6q.dtsi"
#include "imx6qdl-gw5904.dtsi"
/ {
model = "Gateworks Ventana i.MX6 Dual/Quad GW5904";
compatible = "gw,imx6q-gw5904", "gw,ventana", "fsl,imx6q";
};
&sata {
status = "okay";
};
arch/arm/boot/dts/imx6q-icore-ofcap10.dts 0 → 100644
View file @ a43315e3
/*
* Copyright (C) 2016 Amarula Solutions B.V.
* Copyright (C) 2016 Engicam S.r.l.
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "imx6q.dtsi"
#include "imx6qdl-icore.dtsi"
/ {
model = "Engicam i.CoreM6 Quad/Dual OpenFrame Capacitive touch 10.1 Kit";
compatible = "engicam,imx6-icore", "fsl,imx6q";
};
&ldb {
status = "okay";
lvds-channel@0 {
fsl,data-mapping = "spwg";
fsl,data-width = <24>;
status = "okay";
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <60000000>;
hactive = <1280>;
vactive = <800>;
hback-porch = <40>;
hfront-porch = <40>;
vback-porch = <10>;
vfront-porch = <3>;
hsync-len = <80>;
vsync-len = <10>;
};
};
};
};
arch/arm/boot/dts/imx6q-icore-ofcap12.dts 0 → 100644
View file @ a43315e3
/*
* Copyright (C) 2016 Amarula Solutions B.V.
* Copyright (C) 2016 Engicam S.r.l.
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "imx6q.dtsi"
#include "imx6qdl-icore.dtsi"
/ {
model = "Engicam i.CoreM6 Quad/Dual OpenFrame Capacitive touch 12 Kit";
compatible = "engicam,imx6-icore", "fsl,imx6q";
};
&ldb {
status = "okay";
lvds-channel@0 {
fsl,data-mapping = "spwg";
fsl,data-width = <18>;
status = "okay";
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <46800000>;
hactive = <1280>;
vactive = <480>;
hback-porch = <353>;
hfront-porch = <47>;
vback-porch = <39>;
vfront-porch = <4>;
hsync-len = <8>;
vsync-len = <2>;
};
};
};
};
arch/arm/boot/dts/imx6q-icore.dts
View file @ a43315e3
......@@ -57,3 +57,37 @@ &can1 {
&can2 {
status = "okay";
};
&i2c1 {
max11801: touchscreen@48 {
compatible = "maxim,max11801";
reg = <0x48>;
interrupt-parent = <&gpio3>;
interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
};
};
&ldb {
status = "okay";
lvds-channel@0 {
fsl,data-mapping = "spwg";
fsl,data-width = <18>;
status = "okay";
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <60000000>;
hactive = <800>;
vactive = <480>;
hback-porch = <30>;
hfront-porch = <30>;
vback-porch = <5>;
vfront-porch = <5>;
hsync-len = <64>;
vsync-len = <20>;
};
};
};
};
arch/arm/boot/dts/imx6q-utilite-pro.dts
View file @ a43315e3
......@@ -101,9 +101,11 @@ power {
hdmi-connector {
compatible = "hdmi-connector";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hpd>;
type = "a";
ddc-i2c-bus = <&i2c_dvi_ddc>;
hpd-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
port {
hdmi_connector_in: endpoint {
......@@ -209,6 +211,12 @@ MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0
>;
};
pinctrl_hpd: hpdgrp {
fsl,pins = <
MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0
>;
};
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
......
arch/arm/boot/dts/imx6q-zii-rdu2.dts 0 → 100644
View file @ a43315e3
/*
* Copyright (C) 2016-2017 Zodiac Inflight Innovations
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include <imx6q.dtsi>
#include <imx6qdl-zii-rdu2.dtsi>
/ {
model = "ZII RDU2 Board";
compatible = "zii,imx6q-zii-rdu2", "fsl,imx6q";
};
arch/arm/boot/dts/imx6qdl-gw5903.dtsi 0 → 100644
View file @ a43315e3
This diff is collapsed.
arch/arm/boot/dts/imx6qdl-gw5904.dtsi 0 → 100644
View file @ a43315e3
This diff is collapsed.
arch/arm/boot/dts/imx6qdl-icore.dtsi
View file @ a43315e3
......@@ -48,6 +48,13 @@ memory {
reg = <0x10000000 0x80000000>;
};
backlight {
compatible = "pwm-backlight";
pwms = <&pwm3 0 100000>;
brightness-levels = <0 4 8 16 32 64 128 255>;
default-brightness-level = <7>;
};
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "3P3V";
......@@ -136,6 +143,12 @@ &i2c3 {
status = "okay";
};
&pwm3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm3>;
status = "okay";
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
......@@ -246,6 +259,12 @@ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
>;
};
pinctrl_pwm3: pwm3grp {
fsl,pins = <
MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
>;
};
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
......
arch/arm/boot/dts/imx6qdl-sabresd.dtsi
View file @ a43315e3
......@@ -548,6 +548,18 @@ &pwm1 {
status = "okay";
};
&reg_arm {
vin-supply = <&sw1a_reg>;
};
&reg_pu {
vin-supply = <&sw1c_reg>;
};
&reg_soc {
vin-supply = <&sw1c_reg>;
};
&snvs_poweroff {
status = "okay";
};
......
arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi 0 → 100644
View file @ a43315e3
This diff is collapsed.
arch/arm/boot/dts/imx6qdl.dtsi
View file @ a43315e3
......@@ -197,7 +197,7 @@ L2: l2-cache@00a02000 {
arm,shared-override;
};
pcie: pcie@0x01000000 {
pcie: pcie@1ffc000 {
compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
reg = <0x01ffc000 0x04000>,
<0x01f00000 0x80000>;
......@@ -205,6 +205,7 @@ pcie: pcie@0x01000000 {
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
bus-range = <0x00 0xff>;
ranges = <0x81000000 0 0 0x01f80000 0 0x00010000 /* downstream I/O */
0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */
num-lanes = <1>;
......
arch/arm/boot/dts/imx6qp-nitrogen6_som2.dts 0 → 100644
View file @ a43315e3
/*
* Copyright 2017 Boundary Devices, Inc.
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "imx6qp.dtsi"
#include "imx6qdl-nitrogen6_som2.dtsi"
/ {
model = "Boundary Devices i.MX6 Quad Plus Nitrogen6_SOM2 Board";
compatible = "boundary,imx6qp-nitrogen6_som2", "fsl,imx6qp";
};
&sata {
status = "okay";
};
arch/arm/boot/dts/imx6qp-sabresd.dts
View file @ a43315e3
......@@ -50,8 +50,8 @@ / {
compatible = "fsl,imx6qp-sabresd", "fsl,imx6qp";
};
&cpu0 {
arm-supply = <&sw2_reg>;
&reg_arm {
vin-supply = <&sw2_reg>;
};
&iomuxc {
......
arch/arm/boot/dts/imx6qp-zii-rdu2.dts 0 → 100644
View file @ a43315e3
/*
* Copyright (C) 2016-2017 Zodiac Inflight Innovations
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include <imx6qp.dtsi>
#include <imx6qdl-zii-rdu2.dtsi>
/ {
model = "ZII RDU2+ Board";
compatible = "zii,imx6qp-zii-rdu2", "fsl,imx6qp";
};
arch/arm/boot/dts/imx6qp.dtsi
View file @ a43315e3
......@@ -56,40 +56,59 @@ ocram3: sram@00960000 {
clocks = <&clks IMX6QDL_CLK_OCRAM>;
};
ipu1: ipu@02400000 {
compatible = "fsl,imx6qp-ipu", "fsl,imx6q-ipu";
clocks = <&clks IMX6QDL_CLK_IPU1>,
<&clks IMX6QDL_CLK_IPU1_DI0>, <&clks IMX6QDL_CLK_IPU1_DI1>,
<&clks IMX6QDL_CLK_IPU1_DI0_SEL>, <&clks IMX6QDL_CLK_IPU1_DI1_SEL>,
<&clks IMX6QDL_CLK_LDB_DI0_PODF>, <&clks IMX6QDL_CLK_LDB_DI1_PODF>,
<&clks IMX6QDL_CLK_PRG0_APB>;
clock-names = "bus",
"di0", "di1",
"di0_sel", "di1_sel",
"ldb_di0", "ldb_di1", "prg";
};
aips-bus@02100000 {
pre1: pre@21c8000 {
compatible = "fsl,imx6qp-pre";
reg = <0x021c8000 0x1000>;
interrupts = <GIC_SPI 90 IRQ_TYPE_EDGE_RISING>;
clocks = <&clks IMX6QDL_CLK_PRE0>;
clock-names = "axi";
fsl,iram = <&ocram2>;
};
ipu2: ipu@02800000 {
compatible = "fsl,imx6qp-ipu", "fsl,imx6q-ipu";
clocks = <&clks IMX6QDL_CLK_IPU2>,
<&clks IMX6QDL_CLK_IPU2_DI0>, <&clks IMX6QDL_CLK_IPU2_DI1>,
<&clks IMX6QDL_CLK_IPU2_DI0_SEL>, <&clks IMX6QDL_CLK_IPU2_DI1_SEL>,
<&clks IMX6QDL_CLK_LDB_DI0_PODF>, <&clks IMX6QDL_CLK_LDB_DI1_PODF>,
<&clks IMX6QDL_CLK_PRG1_APB>;
clock-names = "bus",
"di0", "di1",
"di0_sel", "di1_sel",
"ldb_di0", "ldb_di1", "prg";
};
pre2: pre@21c9000 {
compatible = "fsl,imx6qp-pre";
reg = <0x021c9000 0x1000>;
interrupts = <GIC_SPI 97 IRQ_TYPE_EDGE_RISING>;
clocks = <&clks IMX6QDL_CLK_PRE1>;
clock-names = "axi";
fsl,iram = <&ocram2>;
};
pcie: pcie@0x01000000 {
compatible = "fsl,imx6qp-pcie", "snps,dw-pcie";
};
pre3: pre@21ca000 {
compatible = "fsl,imx6qp-pre";
reg = <0x021ca000 0x1000>;
interrupts = <GIC_SPI 98 IRQ_TYPE_EDGE_RISING>;
clocks = <&clks IMX6QDL_CLK_PRE2>;
clock-names = "axi";
fsl,iram = <&ocram3>;
};
aips-bus@02100000 {
mmdc0: mmdc@021b0000 { /* MMDC0 */
compatible = "fsl,imx6qp-mmdc", "fsl,imx6q-mmdc";
reg = <0x021b0000 0x4000>;
pre4: pre@21cb000 {
compatible = "fsl,imx6qp-pre";
reg = <0x021cb000 0x1000>;
interrupts = <GIC_SPI 99 IRQ_TYPE_EDGE_RISING>;
clocks = <&clks IMX6QDL_CLK_PRE3>;
clock-names = "axi";
fsl,iram = <&ocram3>;
};
prg1: prg@21cc000 {
compatible = "fsl,imx6qp-prg";
reg = <0x021cc000 0x1000>;
clocks = <&clks IMX6QDL_CLK_PRG0_APB>,
<&clks IMX6QDL_CLK_PRG0_AXI>;
clock-names = "ipg", "axi";
fsl,pres = <&pre1>, <&pre2>, <&pre3>;
};
prg2: prg@21cd000 {
compatible = "fsl,imx6qp-prg";
reg = <0x021cd000 0x1000>;
clocks = <&clks IMX6QDL_CLK_PRG1_APB>,
<&clks IMX6QDL_CLK_PRG1_AXI>;
clock-names = "ipg", "axi";
fsl,pres = <&pre4>, <&pre2>, <&pre3>;
};
};
};
......@@ -101,6 +120,16 @@ &fec {
<0 119 IRQ_TYPE_LEVEL_HIGH>;
};
&ipu1 {
compatible = "fsl,imx6qp-ipu", "fsl,imx6q-ipu";
fsl,prg = <&prg1>;
};
&ipu2 {
compatible = "fsl,imx6qp-ipu", "fsl,imx6q-ipu";
fsl,prg = <&prg2>;
};
&ldb {
clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
<&clks IMX6QDL_CLK_IPU1_DI0_SEL>, <&clks IMX6QDL_CLK_IPU1_DI1_SEL>,
......@@ -110,3 +139,11 @@ &ldb {
"di0_sel", "di1_sel", "di2_sel", "di3_sel",
"di0", "di1";
};
&mmdc0 {
compatible = "fsl,imx6qp-mmdc", "fsl,imx6q-mmdc";
};
&pcie {
compatible = "fsl,imx6qp-pcie", "snps,dw-pcie";
};
arch/arm/boot/dts/imx6sx.dtsi
View file @ a43315e3
......@@ -297,7 +297,8 @@ ecspi4: ecspi@02014000 {
};
uart1: serial@02020000 {
compatible = "fsl,imx6sx-uart", "fsl,imx21-uart";
compatible = "fsl,imx6sx-uart",
"fsl,imx6q-uart", "fsl,imx21-uart";
reg = <0x02020000 0x4000>;
interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6SX_CLK_UART_IPG>,
......@@ -1053,7 +1054,8 @@ qspi2: qspi@021e4000 {
};
uart2: serial@021e8000 {
compatible = "fsl,imx6sx-uart", "fsl,imx21-uart";
compatible = "fsl,imx6sx-uart",
"fsl,imx6q-uart", "fsl,imx21-uart";
reg = <0x021e8000 0x4000>;
interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6SX_CLK_UART_IPG>,
......@@ -1065,7 +1067,8 @@ uart2: serial@021e8000 {
};
uart3: serial@021ec000 {
compatible = "fsl,imx6sx-uart", "fsl,imx21-uart";
compatible = "fsl,imx6sx-uart",
"fsl,imx6q-uart", "fsl,imx21-uart";
reg = <0x021ec000 0x4000>;
interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6SX_CLK_UART_IPG>,
......@@ -1077,7 +1080,8 @@ uart3: serial@021ec000 {
};
uart4: serial@021f0000 {
compatible = "fsl,imx6sx-uart", "fsl,imx21-uart";
compatible = "fsl,imx6sx-uart",
"fsl,imx6q-uart", "fsl,imx21-uart";
reg = <0x021f0000 0x4000>;
interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6SX_CLK_UART_IPG>,
......@@ -1089,7 +1093,8 @@ uart4: serial@021f0000 {
};
uart5: serial@021f4000 {
compatible = "fsl,imx6sx-uart", "fsl,imx21-uart";
compatible = "fsl,imx6sx-uart",
"fsl,imx6q-uart", "fsl,imx21-uart";
reg = <0x021f4000 0x4000>;
interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6SX_CLK_UART_IPG>,
......@@ -1229,7 +1234,8 @@ ecspi5: ecspi@0228c000 {
};
uart6: serial@022a0000 {
compatible = "fsl,imx6sx-uart", "fsl,imx21-uart";
compatible = "fsl,imx6sx-uart",
"fsl,imx6q-uart", "fsl,imx21-uart";
reg = <0x022a0000 0x4000>;
interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6SX_CLK_UART_IPG>,
......@@ -1281,7 +1287,7 @@ pwm8: pwm@0022b0000 {
};
};
pcie: pcie@0x08000000 {
pcie: pcie@8ffc000 {
compatible = "fsl,imx6sx-pcie", "snps,dw-pcie";
reg = <0x08ffc000 0x4000>; /* DBI */
#address-cells = <3>;
......@@ -1293,6 +1299,7 @@ pcie: pcie@0x08000000 {
0x81000000 0 0 0x08f80000 0 0x00010000
/* non-prefetchable memory */
0x82000000 0 0x08000000 0x08000000 0 0x00f00000>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6SX_CLK_PCIE_REF_125M>,
......
arch/arm/boot/dts/imx6ul-14x14-evk.dts
View file @ a43315e3
......@@ -85,11 +85,6 @@ &clks {
assigned-clock-rates = <786432000>;
};
&cpu0 {
arm-supply = <&reg_arm>;
soc-supply = <&reg_soc>;
};
&i2c2 {
clock_frequency = <100000>;
pinctrl-names = "default";
......
arch/arm/boot/dts/imx6ul-geam.dtsi
View file @ a43315e3
......@@ -49,6 +49,23 @@ memory {
reg = <0x80000000 0x08000000>;
};
backlight {
compatible = "pwm-backlight";
pwms = <&pwm8 0 100000>;
brightness-levels = < 0 1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39
40 41 42 43 44 45 46 47 48 49
50 51 52 53 54 55 56 57 58 59
60 61 62 63 64 65 66 67 68 69
70 71 72 73 74 75 76 77 78 79
80 81 82 83 84 85 86 87 88 89
90 91 92 93 94 95 96 97 98 99
100>;
default-brightness-level = <100>;
};
chosen {
stdout-path = &uart1;
};
......@@ -143,12 +160,24 @@ &lcdif {
display = <&display0>;
};
&pwm8 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm8>;
status = "okay";
};
&tsc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_tsc>;
xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
};
&sai2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sai2>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
......@@ -290,6 +319,12 @@ MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79
>;
};
pinctrl_pwm8: pwm8grp {
fsl,pins = <
MX6UL_PAD_ENET1_RX_ER__PWM8_OUT 0x110b0
>;
};
pinctrl_tsc: tscgrp {
fsl,pin = <
MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0xb0
......@@ -299,6 +334,16 @@ MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0xb0
>;
};
pinctrl_sai2: sai2grp {
fsl,pins = <
MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x130b0
MX6UL_PAD_JTAG_TMS__CCM_CLKO1 0x4001b031
MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x17088
MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x17088
MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x120b0
>;
};
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
......
arch/arm/boot/dts/imx6ul-isiot-common.dtsi 0 → 100644
View file @ a43315e3
/*
* Copyright (C) 2016 Amarula Solutions B.V.
* Copyright (C) 2016 Engicam S.r.l.
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
&i2c1 {
stmpe811: gpio-expander@44 {
compatible = "st,stmpe811";
reg = <0x44>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_stmpe>;
interrupt-parent = <&gpio1>;
interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
interrupt-controller;
#interrupt-cells = <2>;
stmpe: touchscreen {
compatible = "st,stmpe-ts";
st,sample-time = <4>;
st,mod-12b = <1>;
st,ref-sel = <0>;
st,adc-freq = <1>;
st,ave-ctrl = <1>;
st,touch-det-delay = <2>;
st,settling = <2>;
st,fraction-z = <7>;
st,i-drive = <1>;
};
};
};
&lcdif {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcdif_dat
&pinctrl_lcdif_ctrl>;
display = <&display0>;
status = "okay";
display0: display {
bits-per-pixel = <16>;
bus-width = <18>;
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <28000000>;
hactive = <800>;
vactive = <480>;
hfront-porch = <30>;
hback-porch = <30>;
hsync-len = <64>;
vback-porch = <5>;
vfront-porch = <5>;
vsync-len = <20>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
};
};
};
&iomuxc {
pinctrl_lcdif_ctrl: lcdifctrlgrp {
fsl,pins = <
MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79
MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79
MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79
MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79
>;
};
pinctrl_lcdif_dat: lcdifdatgrp {
fsl,pins = <
MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79
MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79
MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79
MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79
MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79
MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79
MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79
MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79
MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79
MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79
MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79
MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79
MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79
MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79
MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79
MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79
MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79
MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79
>;
};
pinctrl_stmpe: stmpegrp {
fsl,pins = <
MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x1b0b0
>;
};
};
arch/arm/boot/dts/imx6ul-isiot-emmc.dts
View file @ a43315e3
......@@ -43,6 +43,7 @@
/dts-v1/;
#include "imx6ul-isiot.dtsi"
#include "imx6ul-isiot-common.dtsi"
/ {
model = "Engicam Is.IoT MX6UL eMMC Starter kit";
......
arch/arm/boot/dts/imx6ul-isiot-nand.dts
View file @ a43315e3
......@@ -43,6 +43,7 @@
/dts-v1/;
#include "imx6ul-isiot.dtsi"
#include "imx6ul-isiot-common.dtsi"
/ {
model = "Engicam Is.IoT MX6UL NAND Starter kit";
......
arch/arm/boot/dts/imx6ul-isiot.dtsi
View file @ a43315e3
......@@ -52,6 +52,49 @@ memory {
chosen {
stdout-path = &uart1;
};
backlight {
compatible = "pwm-backlight";
pwms = <&pwm8 0 100000>;
brightness-levels = < 0 1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39
40 41 42 43 44 45 46 47 48 49
50 51 52 53 54 55 56 57 58 59
60 61 62 63 64 65 66 67 68 69
70 71 72 73 74 75 76 77 78 79
80 81 82 83 84 85 86 87 88 89
90 91 92 93 94 95 96 97 98 99
100>;
default-brightness-level = <100>;
};
};
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
status = "okay";
};
&i2c2 {
clock_frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
status = "okay";
};
&pwm8 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm8>;
status = "okay";
};
&sai2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sai2>;
status = "okay";
};
&uart1 {
......@@ -72,6 +115,36 @@ &usdhc1 {
};
&iomuxc {
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
>;
};
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX6UL_PAD_GPIO1_IO00__I2C2_SCL 0x4001b8b0
MX6UL_PAD_GPIO1_IO01__I2C2_SDA 0x4001b8b0
>;
};
pinctrl_pwm8: pwm8grp {
fsl,pins = <
MX6UL_PAD_ENET1_RX_ER__PWM8_OUT 0x110b0
>;
};
pinctrl_sai2: sai2grp {
fsl,pins = <
MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x130b0
MX6UL_PAD_JTAG_TMS__CCM_CLKO1 0x4001b031
MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x17088
MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x17088
MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x120b0
>;
};
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
......
arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
View file @ a43315e3
......@@ -44,11 +44,39 @@ / {
chosen {
stdout-path = "serial0:115200n8";
};
panel: panel {
compatible = "edt,et057090dhu";
backlight = <&bl>;
power-supply = <&reg_3v3>;
port {
panel_in: endpoint {
remote-endpoint = <&lcdif_out>;
};
};
};
reg_3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
reg_5v0: regulator-5v0 {
compatible = "regulator-fixed";
regulator-name = "5V";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
};
&bl {
brightness-levels = <0 4 8 16 32 64 128 255>;
default-brightness-level = <6>;
power-supply = <&reg_3v3>;
status = "okay";
};
......@@ -75,32 +103,11 @@ rtc: m41t0m6@68 {
};
&lcdif {
display = <&display0>;
status = "okay";
display0: lcd-display {
bits-per-pixel = <16>;
bus-width = <18>;
display-timings {
native-mode = <&timing_vga>;
/* Standard VGA timing */
timing_vga: 640x480 {
clock-frequency = <25175000>;
hactive = <640>;
vactive = <480>;
hback-porch = <40>;
hfront-porch = <24>;
vback-porch = <32>;
vfront-porch = <11>;
hsync-len = <96>;
vsync-len = <2>;
de-active = <1>;
hsync-active = <0>;
vsync-active = <0>;
pixelclk-active = <0>;
};
port {
lcdif_out: endpoint {
remote-endpoint = <&panel_in>;
};
};
};
......
arch/arm/boot/dts/imx7-colibri.dtsi
View file @ a43315e3
This diff is collapsed.
arch/arm/boot/dts/imx7d-colibri-eval-v3.dts
View file @ a43315e3
......@@ -57,6 +57,7 @@ reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio4 7 GPIO_ACTIVE_LOW>;
vin-supply = <&reg_5v0>;
};
};
......
arch/arm/boot/dts/imx7d-sdb-sht11.dts 0 → 100644
View file @ a43315e3
/*
* Copyright (C) 2015 Freescale Semiconductor, Inc.
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include "imx7d-sdb.dts"
/ {
sensor {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sensor>;
compatible = "sensirion,sht15";
clk-gpios = <&gpio4 12 0>;
data-gpios = <&gpio4 13 0>;
vcc-supply = <&reg_sht15>;
};
reg_sht15: regulator-sht15 {
compatible = "regulator-fixed";
regulator-name = "reg_sht15";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
};
&i2c3 {
status = "disabled";
};
&iomuxc {
pinctrl_sensor: sensorgrp {
fsl,pins = <
MX7D_PAD_I2C3_SDA__GPIO4_IO13 0x4000007f
MX7D_PAD_I2C3_SCL__GPIO4_IO12 0x4000007f
>;
};
};
arch/arm/boot/dts/imx7s.dtsi
View file @ a43315e3
This diff is collapsed.
arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
View file @ a43315e3
This diff is collapsed.
arch/arm/boot/dts/vf610-zii-dev-rev-c.dts
View file @ a43315e3
This diff is collapsed.
arch/arm/boot/dts/vf610-zii-dev.dtsi
View file @ a43315e3
This diff is collapsed.
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7