Merge redhat.com:/spare/repo/linux-2.6

into redhat.com:/spare/repo/libata-2.6

drivers/scsi/Kconfig

@@ -449,6 +449,14 @@ config SCSI_SATA_SIL
 
 	  If unsure, say N.
 
+config SCSI_SATA_SIS
+	tristate "SiS 964/180 SATA support"
+	depends on SCSI_SATA && PCI
+	help
+	  This option enables support for SiS Serial ATA 964/180.
+
+	  If unsure, say N.
+
 config SCSI_SATA_VIA
 	tristate "VIA SATA support"
 	depends on SCSI_SATA && PCI && EXPERIMENTAL

drivers/scsi/Makefile

@@ -123,6 +123,7 @@ obj-$(CONFIG_SCSI_SATA_PROMISE)	+= libata.o sata_promise.o
 obj-$(CONFIG_SCSI_SATA_SIL)	+= libata.o sata_sil.o
 obj-$(CONFIG_SCSI_SATA_VIA)	+= libata.o sata_via.o
 obj-$(CONFIG_SCSI_SATA_VITESSE)	+= libata.o sata_vsc.o
+obj-$(CONFIG_SCSI_SATA_SIS)	+= libata.o sata_sis.o
 
 obj-$(CONFIG_ARM)		+= arm/
 

drivers/scsi/ata_piix.c

@@ -28,17 +28,24 @@
 #include <linux/libata.h>
 
 #define DRV_NAME	"ata_piix"
-#define DRV_VERSION	"1.01"
+#define DRV_VERSION	"1.02"
 
 enum {
 	PIIX_IOCFG		= 0x54, /* IDE I/O configuration register */
+	ICH5_PMR		= 0x90, /* port mapping register */
 	ICH5_PCS		= 0x92,	/* port control and status */
 
 	PIIX_FLAG_CHECKINTR	= (1 << 29), /* make sure PCI INTx enabled */
 	PIIX_FLAG_COMBINED	= (1 << 30), /* combined mode possible */
 
-	PIIX_COMB_PRI		= (1 << 0), /* combined mode, PATA primary */
-	PIIX_COMB_SEC		= (1 << 1), /* combined mode, PATA secondary */
+	/* combined mode.  if set, PATA is channel 0.
+	 * if clear, PATA is channel 1.
+	 */
+	PIIX_COMB_PATA_P0	= (1 << 1),
+	PIIX_COMB		= (1 << 2), /* combined mode enabled? */
+
+	PIIX_PORT_PRESENT	= (1 << 0),
+	PIIX_PORT_ENABLED	= (1 << 4),
 
 	PIIX_80C_PRI		= (1 << 5) | (1 << 4),
 	PIIX_80C_SEC		= (1 << 7) | (1 << 6),
@@ -53,7 +60,6 @@ static int piix_init_one (struct pci_dev *pdev,
 
 static void piix_pata_phy_reset(struct ata_port *ap);
 static void piix_sata_phy_reset(struct ata_port *ap);
-static void piix_sata_port_disable(struct ata_port *ap);
 static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev,
 			      unsigned int pio);
 static void piix_set_udmamode (struct ata_port *ap, struct ata_device *adev,
@@ -137,7 +143,7 @@ static struct ata_port_operations piix_pata_ops = {
 };
 
 static struct ata_port_operations piix_sata_ops = {
-	.port_disable		= piix_sata_port_disable,
+	.port_disable		= ata_port_disable,
 	.set_piomode		= piix_set_piomode,
 	.set_udmamode		= piix_set_udmamode,
 
@@ -259,54 +265,48 @@ static void piix_pata_phy_reset(struct ata_port *ap)
 }
 
 /**
- *	piix_pcs_probe - Probe SATA port configuration and status register
- *	@ap: Port to probe
- *	@have_port: (output) Non-zero if SATA port is enabled
- *	@have_device: (output) Non-zero if SATA phy indicates device present
+ *	piix_sata_probe - Probe PCI device for present SATA devices
+ *	@pdev: PCI device to probe
  *
  *	Reads SATA PCI device's PCI config register Port Configuration
  *	and Status (PCS) to determine port and device availability.
  *
  *	LOCKING:
  *	None (inherited from caller).
- */
-static void piix_pcs_probe (struct ata_port *ap, unsigned int *have_port,
-			    unsigned int *have_device)
-{
-	struct pci_dev *pdev = ap->host_set->pdev;
-	u16 pcs;
-
-	pci_read_config_word(pdev, ICH5_PCS, &pcs);
-
-	/* is SATA port enabled? */
-	if (pcs & (1 << ap->port_no)) {
-		*have_port = 1;
-
-		if (pcs & (1 << (ap->port_no + 4)))
-			*have_device = 1;
-	}
-}
-
-/**
- *	piix_pcs_disable - Disable SATA port
- *	@ap: Port to disable
  *
- *	Disable SATA phy for specified port.
- *
- *	LOCKING:
- *	None (inherited from caller).
+ *	RETURNS:
+ *	Non-zero if device detected, zero otherwise.
  */
-static void piix_pcs_disable (struct ata_port *ap)
+static int piix_sata_probe (struct ata_port *ap)
 {
 	struct pci_dev *pdev = ap->host_set->pdev;
-	u16 pcs;
+	int combined = (ap->flags & ATA_FLAG_SLAVE_POSS);
+	int orig_mask, mask, i;
+	u8 pcs;
+
+	mask = (PIIX_PORT_PRESENT << ap->port_no) |
+	       (PIIX_PORT_ENABLED << ap->port_no);
+
+	pci_read_config_byte(pdev, ICH5_PCS, &pcs);
+	orig_mask = (int) pcs & 0xff;
+
+	/* TODO: this is vaguely wrong for ICH6 combined mode,
+	 * where only two of the four SATA ports are mapped
+	 * onto a single ATA channel.  It is also vaguely inaccurate
+	 * for ICH5, which has only two ports.  However, this is ok,
+	 * as further device presence detection code will handle
+	 * any false positives produced here.
+	 */
 
-	pci_read_config_word(pdev, ICH5_PCS, &pcs);
+	for (i = 0; i < 4; i++) {
+		mask = (PIIX_PORT_PRESENT << i) | (PIIX_PORT_ENABLED << i);
 
-	if (pcs & (1 << ap->port_no)) {
-		pcs &= ~(1 << ap->port_no);
-		pci_write_config_word(pdev, ICH5_PCS, pcs);
+		if ((orig_mask & mask) == mask)
+			if (combined || (i == ap->port_no))
+				return 1;
 	}
+
+	return 0;
 }
 
 /**
@@ -321,8 +321,6 @@ static void piix_pcs_disable (struct ata_port *ap)
 
 static void piix_sata_phy_reset(struct ata_port *ap)
 {
-	unsigned int have_port = 0, have_dev = 0;
-
 	if (!pci_test_config_bits(ap->host_set->pdev,
 				  &piix_enable_bits[ap->port_no])) {
 		ata_port_disable(ap);
@@ -330,21 +328,9 @@ static void piix_sata_phy_reset(struct ata_port *ap)
 		return;
 	}
 
-	piix_pcs_probe(ap, &have_port, &have_dev);
-
-	/* if port not enabled, exit */
-	if (!have_port) {
+	if (!piix_sata_probe(ap)) {
 		ata_port_disable(ap);
-		printk(KERN_INFO "ata%u: SATA port disabled. ignoring.\n",
-		       ap->id);
-		return;
-	}
-
-	/* if port enabled but no device, disable port and exit */
-	if (!have_dev) {
-		piix_sata_port_disable(ap);
-		printk(KERN_INFO "ata%u: SATA port has no device. disabling.\n",
-		       ap->id);
+		printk(KERN_INFO "ata%u: SATA port has no device.\n", ap->id);
 		return;
 	}
 
@@ -355,22 +341,6 @@ static void piix_sata_phy_reset(struct ata_port *ap)
 	ata_bus_reset(ap);
 }
 
-/**
- *	piix_sata_port_disable - Disable SATA port
- *	@ap: Port to disable.
- *
- *	Disable SATA port.
- *
- *	LOCKING:
- *	None (inherited from caller).
- */
-
-static void piix_sata_port_disable(struct ata_port *ap)
-{
-	ata_port_disable(ap);
-	piix_pcs_disable(ap);
-}
-
 /**
  *	piix_set_piomode - Initialize host controller PATA PIO timings
  *	@ap: Port whose timings we are configuring
@@ -493,31 +463,6 @@ static void piix_set_udmamode (struct ata_port *ap, struct ata_device *adev,
 	}
 }
 
-/**
- *	piix_probe_combined - Determine if PATA and SATA are combined
- *	@pdev: PCI device to examine
- *	@mask: (output) zero, %PIIX_COMB_PRI or %PIIX_COMB_SEC
- *
- *	Determine if BIOS has secretly stuffed a PATA port into our
- *	otherwise-beautiful SATA PCI device.
- *
- *	LOCKING:
- *	Inherited from PCI layer (may sleep).
- */
-static void piix_probe_combined (struct pci_dev *pdev, unsigned int *mask)
-{
-	u8 tmp;
-
-	pci_read_config_byte(pdev, 0x90, &tmp); /* combined mode reg */
-	tmp &= 0x6; 	/* interesting bits 2:1, PATA primary/secondary */
-
-	/* backwards from what one might expect */
-	if (tmp == 0x4)	/* bits 10x */
-		*mask |= PIIX_COMB_SEC;
-	if (tmp == 0x6)	/* bits 11x */
-		*mask |= PIIX_COMB_PRI;
-}
-
 /* move to PCI layer, integrate w/ MSI stuff */
 static void pci_enable_intx(struct pci_dev *pdev)
 {
@@ -550,7 +495,7 @@ static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 	static int printed_version;
 	struct ata_port_info *port_info[2];
 	unsigned int combined = 0, n_ports = 1;
-	unsigned int pata_comb = 0, sata_comb = 0;
+	unsigned int pata_chan = 0, sata_chan = 0;
 
 	if (!printed_version++)
 		printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
@@ -561,8 +506,19 @@ static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 
 	port_info[0] = &piix_port_info[ent->driver_data];
 	port_info[1] = NULL;
-	if (port_info[0]->host_flags & PIIX_FLAG_COMBINED)
-		piix_probe_combined(pdev, &combined);
+
+	if (port_info[0]->host_flags & PIIX_FLAG_COMBINED) {
+		u8 tmp;
+		pci_read_config_byte(pdev, ICH5_PMR, &tmp);
+
+		if (tmp & PIIX_COMB) {
+			combined = 1;
+			if (tmp & PIIX_COMB_PATA_P0)
+				sata_chan = 1;
+			else
+				pata_chan = 1;
+		}
+	}
 
 	/* On ICH5, some BIOSen disable the interrupt using the
 	 * PCI_COMMAND_INTX_DISABLE bit added in PCI 2.3.
@@ -573,15 +529,10 @@ static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 	if (port_info[0]->host_flags & PIIX_FLAG_CHECKINTR)
 		pci_enable_intx(pdev);
 
-	if (combined & PIIX_COMB_PRI)
-		sata_comb = 1;
-	else if (combined & PIIX_COMB_SEC)
-		pata_comb = 1;
-
-	if (pata_comb || sata_comb) {
-		port_info[sata_comb] = &piix_port_info[ent->driver_data];
-		port_info[sata_comb]->host_flags |= ATA_FLAG_SLAVE_POSS; /* sigh */
-		port_info[pata_comb] = &piix_port_info[ich5_pata]; /*ich5-specific*/
+	if (combined) {
+		port_info[sata_chan] = &piix_port_info[ent->driver_data];
+		port_info[sata_chan]->host_flags |= ATA_FLAG_SLAVE_POSS;
+		port_info[pata_chan] = &piix_port_info[ich5_pata];
 		n_ports++;
 
 		printk(KERN_WARNING DRV_NAME ": combined mode detected\n");

drivers/scsi/libata.h

@@ -37,7 +37,7 @@ struct ata_scsi_args {
 
 
 /* libata-core.c */
-extern unsigned int ata_dev_id_string(struct ata_device *dev, unsigned char *s,
+extern void ata_dev_id_string(struct ata_device *dev, unsigned char *s,
 			      unsigned int ofs, unsigned int len);
 extern struct ata_queued_cmd *ata_qc_new_init(struct ata_port *ap,
 				      struct ata_device *dev);
@@ -50,9 +50,6 @@ extern void ata_thread_wake(struct ata_port *ap, unsigned int thr_state);
 
 /* libata-scsi.c */
 extern void ata_to_sense_error(struct ata_queued_cmd *qc);
-extern void ata_scsi_rw_queue(struct ata_port *ap, struct ata_device *dev,
-		      struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *),
-		      unsigned int cmd_size);
 extern int ata_scsi_error(struct Scsi_Host *host);
 extern unsigned int ata_scsiop_inq_std(struct ata_scsi_args *args, u8 *rbuf,
 			       unsigned int buflen);

drivers/scsi/sata_sis.c

+/*
+ *  sata_sis.c - Silicon Integrated Systems SATA
+ *
+ *  Copyright 2004 Uwe Koziolek
+ *
+ *  The contents of this file are subject to the Open
+ *  Software License version 1.1 that can be found at
+ *  http://www.opensource.org/licenses/osl-1.1.txt and is included herein
+ *  by reference.
+ *
+ *  Alternatively, the contents of this file may be used under the terms
+ *  of the GNU General Public License version 2 (the "GPL") as distributed
+ *  in the kernel source COPYING file, in which case the provisions of
+ *  the GPL are applicable instead of the above.  If you wish to allow
+ *  the use of your version of this file only under the terms of the
+ *  GPL and not to allow others to use your version of this file under
+ *  the OSL, indicate your decision by deleting the provisions above and
+ *  replace them with the notice and other provisions required by the GPL.
+ *  If you do not delete the provisions above, a recipient may use your
+ *  version of this file under either the OSL or the GPL.
+ *
+ */
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include "scsi.h"
+#include "hosts.h"
+#include <linux/libata.h>
+
+#define DRV_NAME	"sata_sis"
+#define DRV_VERSION	"0.04"
+
+enum {
+	sis_180			= 0,
+};
+
+static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
+static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg);
+static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
+
+static struct pci_device_id sis_pci_tbl[] = {
+	{ PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_180, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sis_180 },
+	{ }	/* terminate list */
+};
+
+
+static struct pci_driver sis_pci_driver = {
+	.name			= DRV_NAME,
+	.id_table		= sis_pci_tbl,
+	.probe			= sis_init_one,
+	.remove			= ata_pci_remove_one,
+};
+
+static Scsi_Host_Template sis_sht = {
+	.module			= THIS_MODULE,
+	.name			= DRV_NAME,
+	.queuecommand		= ata_scsi_queuecmd,
+	.eh_strategy_handler	= ata_scsi_error,
+	.can_queue		= ATA_DEF_QUEUE,
+	.this_id		= ATA_SHT_THIS_ID,
+	.sg_tablesize		= ATA_MAX_PRD,
+	.max_sectors		= ATA_MAX_SECTORS,
+	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
+	.emulated		= ATA_SHT_EMULATED,
+	.use_clustering		= ATA_SHT_USE_CLUSTERING,
+	.proc_name		= DRV_NAME,
+	.dma_boundary		= ATA_DMA_BOUNDARY,
+	.slave_configure	= ata_scsi_slave_config,
+	.bios_param		= ata_std_bios_param,
+};
+
+static struct ata_port_operations sis_ops = {
+	.port_disable		= ata_port_disable,
+	.tf_load		= ata_tf_load_pio,
+	.tf_read		= ata_tf_read_pio,
+	.check_status		= ata_check_status_pio,
+	.exec_command		= ata_exec_command_pio,
+	.phy_reset		= sata_phy_reset,
+	.bmdma_start            = ata_bmdma_start_pio,
+	.fill_sg		= ata_fill_sg,
+	.eng_timeout		= ata_eng_timeout,
+	.irq_handler		= ata_interrupt,
+	.scr_read		= sis_scr_read,
+	.scr_write		= sis_scr_write,
+	.port_start		= ata_port_start,
+	.port_stop		= ata_port_stop,
+};
+
+
+MODULE_AUTHOR("Uwe Koziolek");
+MODULE_DESCRIPTION("low-level driver for Silicon Integratad Systems SATA controller");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, sis_pci_tbl);
+
+
+static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg)
+{
+	if (sc_reg >= 16)
+		return 0xffffffffU;
+
+	return inl(ap->ioaddr.scr_addr + (sc_reg * 4));
+}
+
+static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
+{
+	if (sc_reg >= 16)
+		return;
+	outl(val, ap->ioaddr.scr_addr + (sc_reg * 4));
+}
+
+/* move to PCI layer, integrate w/ MSI stuff */
+static void pci_enable_intx(struct pci_dev *pdev)
+{
+	u16 pci_command;
+
+	pci_read_config_word(pdev, PCI_COMMAND, &pci_command);
+	if (pci_command & PCI_COMMAND_INTX_DISABLE) {
+		pci_command &= ~PCI_COMMAND_INTX_DISABLE;
+		pci_write_config_word(pdev, PCI_COMMAND, pci_command);
+	}
+}
+
+static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+	struct ata_probe_ent *probe_ent = NULL;
+	int rc;
+
+	rc = pci_enable_device(pdev);
+	if (rc)
+		return rc;
+
+	rc = pci_request_regions(pdev, DRV_NAME);
+	if (rc)
+		goto err_out;
+
+	rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+	if (rc)
+		goto err_out_regions;
+	rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+	if (rc)
+		goto err_out_regions;
+
+	probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL);
+	if (!probe_ent) {
+		rc = -ENOMEM;
+		goto err_out_regions;
+	}
+
+	memset(probe_ent, 0, sizeof(*probe_ent));
+	probe_ent->pdev = pdev;
+	INIT_LIST_HEAD(&probe_ent->node);
+
+	probe_ent->sht = &sis_sht;
+	probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_SATA_RESET |
+				ATA_FLAG_NO_LEGACY;
+	probe_ent->pio_mask = 0x03;
+	probe_ent->udma_mask = 0x7f;
+	probe_ent->port_ops = &sis_ops;
+
+	probe_ent->port[0].cmd_addr = pci_resource_start(pdev, 0);
+	ata_std_ports(&probe_ent->port[0]);
+	probe_ent->port[0].ctl_addr =
+		pci_resource_start(pdev, 1) | ATA_PCI_CTL_OFS;
+	probe_ent->port[0].bmdma_addr = pci_resource_start(pdev, 4);
+	probe_ent->port[0].scr_addr = pci_resource_start(pdev, 5);
+
+	probe_ent->port[1].cmd_addr = pci_resource_start(pdev, 2);
+	ata_std_ports(&probe_ent->port[1]);
+	probe_ent->port[1].ctl_addr =
+		pci_resource_start(pdev, 3) | ATA_PCI_CTL_OFS;
+	probe_ent->port[1].bmdma_addr = pci_resource_start(pdev, 4) + 8;
+	probe_ent->port[1].scr_addr = pci_resource_start(pdev, 5) + 64;
+
+	probe_ent->n_ports = 2;
+	probe_ent->irq = pdev->irq;
+	probe_ent->irq_flags = SA_SHIRQ;
+
+	pci_set_master(pdev);
+	pci_enable_intx(pdev);
+
+	/* FIXME: check ata_device_add return value */
+	ata_device_add(probe_ent);
+	kfree(probe_ent);
+
+	return 0;
+
+err_out_regions:
+	pci_release_regions(pdev);
+
+err_out:
+	pci_disable_device(pdev);
+	return rc;
+
+}
+
+static int __init sis_init(void)
+{
+	return pci_module_init(&sis_pci_driver);
+}
+
+static void __exit sis_exit(void)
+{
+	pci_unregister_driver(&sis_pci_driver);
+}
+
+
+module_init(sis_init);
+module_exit(sis_exit);

include/linux/ata.h

@@ -102,16 +102,6 @@ enum {
 	ATA_REG_DEVSEL		= ATA_REG_DEVICE,
 	ATA_REG_IRQ		= ATA_REG_NSECT,
 
-	/* ATA taskfile protocols */
-	ATA_PROT_UNKNOWN	= 0,
-	ATA_PROT_NODATA		= 1,
-	ATA_PROT_PIO_READ	= 2,
-	ATA_PROT_PIO_WRITE	= 3,
-	ATA_PROT_DMA_READ	= 4,
-	ATA_PROT_DMA_WRITE	= 5,
-	ATA_PROT_ATAPI		= 6,
-	ATA_PROT_ATAPI_DMA	= 7,
-
 	/* ATA device commands */
 	ATA_CMD_EDD		= 0x90,	/* execute device diagnostic */
 	ATA_CMD_ID_ATA		= 0xEC,
@@ -156,14 +146,55 @@ enum {
 	SCR_CONTROL		= 2,
 	SCR_ACTIVE		= 3,
 	SCR_NOTIFICATION	= 4,
+
+	/* struct ata_taskfile flags */
+	ATA_TFLAG_LBA48		= (1 << 0), /* enable 48-bit LBA and "HOB" */
+	ATA_TFLAG_ISADDR	= (1 << 1), /* enable r/w to nsect/lba regs */
+	ATA_TFLAG_DEVICE	= (1 << 2), /* enable r/w to device reg */
+	ATA_TFLAG_WRITE		= (1 << 3), /* data dir: host->dev==1 (write) */
+};
+
+enum ata_tf_protocols {
+	/* ATA taskfile protocols */
+	ATA_PROT_UNKNOWN,	/* unknown/invalid */
+	ATA_PROT_NODATA,	/* no data */
+	ATA_PROT_PIO,		/* PIO single sector */
+	ATA_PROT_PIO_MULT,	/* PIO multiple sector */
+	ATA_PROT_DMA,		/* DMA */
+	ATA_PROT_ATAPI,		/* packet command */
+	ATA_PROT_ATAPI_DMA,	/* packet command with special DMA sauce */
 };
 
 /* core structures */
+
 struct ata_prd {
 	u32			addr;
 	u32			flags_len;
 } __attribute__((packed));
 
+struct ata_taskfile {
+	unsigned long		flags;		/* ATA_TFLAG_xxx */
+	u8			protocol;	/* ATA_PROT_xxx */
+
+	u8			ctl;		/* control reg */
+
+	u8			hob_feature;	/* additional data */
+	u8			hob_nsect;	/* to support LBA48 */
+	u8			hob_lbal;
+	u8			hob_lbam;
+	u8			hob_lbah;
+
+	u8			feature;
+	u8			nsect;
+	u8			lbal;
+	u8			lbam;
+	u8			lbah;
+
+	u8			device;
+
+	u8			command;	/* IO operation */
+};
+
 #define ata_id_is_ata(dev)	(((dev)->id[0] & (1 << 15)) == 0)
 #define ata_id_has_lba48(dev)	((dev)->id[83] & (1 << 10))
 #define ata_id_has_lba(dev)	((dev)->id[49] & (1 << 8))

include/linux/libata.h

@@ -107,12 +107,6 @@ enum {
 	ATA_FLAG_MMIO		= (1 << 6), /* use MMIO, not PIO */
 	ATA_FLAG_SATA_RESET	= (1 << 7), /* use COMRESET */
 
-	/* struct ata_taskfile flags */
-	ATA_TFLAG_LBA48		= (1 << 0),
-	ATA_TFLAG_ISADDR	= (1 << 1), /* enable r/w to nsect/lba regs */
-	ATA_TFLAG_DEVICE	= (1 << 2), /* enable r/w to device reg */
-
-	ATA_QCFLAG_WRITE	= (1 << 0), /* read==0, write==1 */
 	ATA_QCFLAG_ACTIVE	= (1 << 1), /* cmd not yet ack'd to scsi lyer */
 	ATA_QCFLAG_DMA		= (1 << 2), /* data delivered via DMA */
 	ATA_QCFLAG_ATAPI	= (1 << 3), /* is ATAPI packet command? */
@@ -223,29 +217,6 @@ struct ata_host_set {
 	struct ata_port *	ports[0];
 };
 
-struct ata_taskfile {
-	unsigned long		flags;		/* ATA_TFLAG_xxx */
-	u8			protocol;	/* ATA_PROT_xxx */
-
-	u8			ctl;		/* control reg */
-
-	u8			hob_feature;	/* additional data */
-	u8			hob_nsect;	/* to support LBA48 */
-	u8			hob_lbal;
-	u8			hob_lbam;
-	u8			hob_lbah;
-
-	u8			feature;
-	u8			nsect;
-	u8			lbal;
-	u8			lbam;
-	u8			lbah;
-
-	u8			device;
-
-	u8			command;	/* IO operation */
-};
-
 struct ata_queued_cmd {
 	struct ata_port		*ap;
 	struct ata_device	*dev;
@@ -293,6 +264,11 @@ struct ata_device {
 						 * ATAPI7 spec size, 40 ASCII
 						 * characters
 						 */
+
+	/* cache info about current transfer mode */
+	u8			xfer_protocol;	/* taskfile xfer protocol */
+	u8			read_cmd;	/* opcode to use on read */
+	u8			write_cmd;	/* opcode to use on write */
 };
 
 struct ata_engine {
@@ -408,7 +384,6 @@ extern int ata_scsi_detect(Scsi_Host_Template *sht);
 extern int ata_scsi_queuecmd(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *));
 extern int ata_scsi_error(struct Scsi_Host *host);
 extern int ata_scsi_release(struct Scsi_Host *host);
-extern int ata_scsi_slave_config(struct scsi_device *sdev);
 extern unsigned int ata_host_intr(struct ata_port *ap, struct ata_queued_cmd *qc);
 /*
  * Default driver ops implementations
@@ -433,6 +408,7 @@ extern void ata_eng_timeout(struct ata_port *ap);
 extern int ata_std_bios_param(struct scsi_device *sdev,
 			      struct block_device *bdev,
 			      sector_t capacity, int geom[]);
+extern int ata_scsi_slave_config(struct scsi_device *sdev);
 
 
 static inline unsigned long msecs_to_jiffies(unsigned long msecs)

include/linux/pci_ids.h

@@ -572,6 +572,7 @@
 #define PCI_DEVICE_ID_SI_503		0x0008
 #define PCI_DEVICE_ID_SI_ACPI		0x0009
 #define PCI_DEVICE_ID_SI_LPC		0x0018
+#define PCI_DEVICE_ID_SI_180		0x0180
 #define PCI_DEVICE_ID_SI_5597_VGA	0x0200
 #define PCI_DEVICE_ID_SI_6205		0x0205
 #define PCI_DEVICE_ID_SI_501		0x0406