Commit a7a1d9da authored by Bruce Allan's avatar Bruce Allan Committed by Jeff Kirsher

e1000e: cleanup checkpatch braces checks

Resolve the following strict checkpatch checks:
CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
CHECK:BRACES: Blank lines aren't necessary before a close brace '}'
CHECK:BRACES: braces {} should be used on all arms of this statement
Signed-off-by: default avatarBruce Allan <bruce.w.allan@intel.com>
Tested-by: default avatarAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
parent c556d607
......@@ -1534,7 +1534,6 @@ static s32 e1000_check_for_serdes_link_82571(struct e1000_hw *hw)
rxcw = er32(RXCW);
if ((rxcw & E1000_RXCW_SYNCH) && !(rxcw & E1000_RXCW_IV)) {
/* Receiver is synchronized with no invalid bits. */
switch (mac->serdes_link_state) {
case e1000_serdes_link_autoneg_complete:
......
......@@ -130,7 +130,6 @@ static int e1000_get_settings(struct net_device *netdev,
u32 speed;
if (hw->phy.media_type == e1000_media_type_copper) {
ecmd->supported = (SUPPORTED_10baseT_Half |
SUPPORTED_10baseT_Full |
SUPPORTED_100baseT_Half |
......@@ -328,12 +327,12 @@ static int e1000_set_settings(struct net_device *netdev,
}
/* reset the link */
if (netif_running(adapter->netdev)) {
e1000e_down(adapter);
e1000e_up(adapter);
} else
} else {
e1000e_reset(adapter);
}
clear_bit(__E1000_RESETTING, &adapter->state);
return 0;
......
......@@ -3991,7 +3991,6 @@ void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw)
* The SMBus release must also be disabled on LCD reset.
*/
if (!(er32(FWSM) & E1000_ICH_FWSM_FW_VALID)) {
/* Enable proxy to reset only on power good. */
e1e_rphy_locked(hw, I217_PROXY_CTRL, &phy_reg);
phy_reg |= I217_PROXY_CTRL_AUTO_DISABLE;
......
......@@ -87,7 +87,6 @@ struct e1000_reg_info {
};
static const struct e1000_reg_info e1000_reg_info_tbl[] = {
/* General Registers */
{E1000_CTRL, "CTRL"},
{E1000_STATUS, "STATUS"},
......@@ -6394,7 +6393,6 @@ static void e1000_io_resume(struct pci_dev *pdev)
*/
if (!(adapter->flags & FLAG_HAS_AMT))
e1000e_get_hw_control(adapter);
}
static void e1000_print_device_info(struct e1000_adapter *adapter)
......
......@@ -2474,7 +2474,6 @@ s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data)
hw->phy.addr = 1;
if (offset > MAX_PHY_MULTI_PAGE_REG) {
/* Page is shifted left, PHY expects (page x 32) */
ret_val = e1000e_write_phy_reg_mdic(hw, BM_PHY_PAGE_SELECT,
page);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment